Search Documents

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By D. F. Malan, R. P. Els

The limit equilibrium model, used in displacement discontinuity codes, is a popular method to simulate pillar failure. This paper investigates the use of physical modelling to calibrate this model. For the experiments, an artificial pillar material was prepared and cubes were poured using the standard 100 mm × 100 mm civil engineering concrete moulds. The friction angle between the cubes and the platens of the testing machine was varied by using soap and sandpaper. Different modes of failure were observed depending on the friction angle. Of interest is that significant loadshedding was recorded for some specimens which visually remained mostly intact. This highlights the difficulty of classifying pillars as failed or intact in underground stopes where spalling is observed. The laboratory models enabled a more precise calibration of the limit equilibrium model compared to previous attempts. Guidelines to assist with calibration of the model are given in the paper. The limit equilibrium model appears to be a useful approximation of the pillar failure as it could simulate the stress-strain behaviour of the laboratory models.

May 3, 2023

By R. B. MacGillivray

The No. 2 Seam at Van Dyks Drift Colliery was found to be made up of six easily recognizable bands or plies of differing qualities. Not only did the plies differ from one another in quality, but their thickness and quality varied laterally across the mine. The economic production of a Iow-ash blendcoking coal for supply to the Japanese Steel Mills called for the mining of different portions of the seam. The portions that could be extracted economically varied in thickness and position within the No. 2 Seam across the mine. A unique system of selective mining had to be developed involving the dispatch of two separate streams of coal out of the mine. Conventional American mechanized pillarand-stall mining was used, and the productivity was improved by the installation of twin conveyor belts into a double-header section. The method of grade control that was instituted to ensure efficient extraction of the available coal reserves is described.

Jan 1, 1985

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

By T. M. Chagwedera, A. E. Lewis, J. Chivavava

Eutectic freeze crystallisation is a novel separation technique that can be applied to treat brine solutions such as reverse osmosis retentates, which are often a mixture of different inorganic salts. The treatment of calcium sulphate-rich brine solutions through eutectic freeze crystallisation has resulted in gypsum scale formation on the walls of the crystallisers and ancillary equipment. In order to prevent gypsum scaling on equipment surfaces, it is essential to understand the mechanism of gypsum scaling on cold surfaces. This paper focused on the interaction between gypsum crystallisation in the bulk solution and scaling on the crystalliser walls in the presence of gypsum seeds. A cooled, U-shaped stainless-steel tube suspended in the saturated solution was employed as the scaling surface. Preliminary results showed that the scale layer was predominantly composed of needle-type and hexagonal prismatic crystals. The rate of scale deposition was highest during the first 24 hours, thereafter it decreased. A thin scale layer was observed to have coated the tube within the first hour of the experiment. Seeding, using reagent grade gypsum crystals, was effective in reducing scale layer formation through providing a surface for growth. The highest scale reduction, 81%, was realised at a seed loading of 0.50 g/L. At a high seed loading of 4.01 g/L, the seed material adhered to the tube. Keywords: Gypsum, eutectic freeze crystallization, seeding, scaling, cooling crystallisation

Jan 1, 2020

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By M. E. Rossi, C. Badenhorst

Conditional bias occurs when the expected value of the true grade conditional on the estimated grade is not equal to the estimated grade. It is a quantification of how the average of estimates differs from the true value. Conditional bias is present in all resource estimates due to the unavoidable properties of kriging, and indeed all linear estimation (regression) methods. In a mining resource estimation context, the degree of conditional bias is dependent on the spacing of the conditioning data; more data leads to the expectation of less conditional bias This paper discusses conditional bias from two perspectives: 1. 2. Estimates seeking to eliminate, as much as possible, conditional bias; and Estimates that accept a larger amount of conditional bias in resource models, in order to achieve a specific outcome. The problem of conditional bias in estimation can only be fully appreciated if the objective or purpose of a resource model is understood. There are instances where conditional bias should be avoided because it is not reasonable to make decisions using estimates that are known to be wrong in expected value; for example, when making a final decision in grade control with respect to the destination of the material. In most instances in the mining resource estimation context, however, the estimated values will not be “final estimates”, but “interim estimates”, meaning that in the future more data will be obtained, and the ”interim estimate” will then be updated. In this context, the most useful resource model is an interim model that is able to predict the final model estimates, despite not having all the data available that will be collected in the future. This is the objective, for example, of a recoverable “long-term” model developed prior to operating a mine, for example at the feasibility stage. It attempts to predict the ore that a processing plant will receive, well into the future. In such cases, it can be unequivocally demonstrated that conditional bias is not only unavoidable, it is a necessity.

Sep 1, 2021

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By O. T. Konina, V. A. Masloboev, A. V. Svetlov, E. A. Krasavtseva, D. V. Makarov, A. A. Goryachev

Dusting phenomena have been examined at the tailings storage facility of Apatit JSC Kirovsk, a mining operation located in the far north of the Russian Federation. The material composition of the tailings was identified. Existing dust suppression methods were examined. Field observations were undertaken and official data was obtained from the Murmansk Administration for Hydrometeorology and Environmental Monitoring, and analysed. A database was built for forecasting dusting according to critical scenarios in order to estimate the peak MPCs of suspended solids in the atmospheric air. Mitigation measures were formulated and recommended to the mining operation. Keywords: Mineral dust particles, apatite-nepheline ore concentration tailings, suspended solids MPC, climate change

Jan 1, 2020

By E. Marè, D. R. Groot, R. Engelbrecht, T. Coetsee

Hydrogen peroxide is often used as an oxidising agent in experimental waste electronic equipment (WEE) leaching work. However, the high cost of peroxide is a negative factor in its consideration in further process development. A few studies have reported on the efficient application of peroxide addition schedules to ensure optimum reagent consumption. Large quantities of unleached substrate material contained in WEE feed material result in a large dead volume of material in the leaching reactor. This factor necessitates fast reaction rates to enable the use of a high feed material throughput reactor to enhance overall project viability via hydrometallurgical processing. In this study the effects of hydrogen peroxide addition schedules on base metal leaching efficiency and solution temperatures were tested at laboratory scale. The results showed that overall peroxide consumption can be optimised to lower levels by matching peroxide additions to the particular feed material’s leaching behaviour. A simplified integrated model for peroxide decomposition is used to explain its effect on solution temperatures and leaching rates. Keywords: Peroxide consumption, waste electronic equipment, copper leaching, integrated model

Jan 1, 2020

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025