Search Documents

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

By E. Kuipa, J. N. Lekunze

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore boLittle attention has been paid to the rehabilitation of derelict and ownerless mines in South Africa after their lifespan. This paper aims to explore management gaps in legislation that have resulted in the non-rehabilitation of derelict and ownerless mines in South Africa. There is growing evidence that supports the distressing effects of mining on people living around these mines in the North West Province. This paper was motivated by the current socio-economic status quo of old mining towns, the influx of illegal miners (Zama Zamas), severe environmental damages, and the violence associated with derelict mines. Underpinning this research was an ecosystem approach and integrated resources management principles, which formed the foundation for the decision-making process.The researcher used a mixed-method approach and employed convergent techniques. A semi-structured instrument was used to collect data from 200 respondents. The results indicated that there is a dire need for community-based consultative processes, and an absence of clear guidelines for derelict and ownerless mines to pressure mine management to adhere to rehabilitation standards. Moreover, the mining charter is ambiguous regarding policy implementation, budgetary allocation, and duration of the rehabilitation of these mines. The paper concluded that management challenges associated with derelict mines can be reduced if all stakeholders follow the guidelines as outlined in the environmental legislative framework (NEMA) of South Africa while being open to innovations in line with international best practices. It also contributes towards the development of guidelines for the management and implementation of legislation related to derelict and ownerless mines in South Africa from a philosophical, theoretical, and policy perspectivedies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Oct 9, 2024

By J. Mothomogolo

Mining projects are capital-intensive and are also characterized by high technical and economic risks. These factors pose challenges to mining entrepreneurs when they seek to raise seed capital for mining start-ups. There are limited sources of mining investment funds in South Africa and each has shortcomings due to one reason or another. Another impediment is South Africa?s status as a developing economy, in which the standards of living ? which in turn influences the savings culture ? the limited GDPs and budget, the socio-political environment, and banking, mining, treasury and other regulations, determine the size of investments, particularly in mining ventures. The proposed funding mechanism was developed with the aim of filling the gaps identified in existing funding mechanisms that were developed by the government with the introduction of the Minerals and Petroleum Resources Development Act (MPRDA), 2002. The shortcomings identified were presented to the study participants as questions to obtain views that were used to define innovative ways of raising mining start-up capital. Most participants in the study supported the derived hypotheses and proposals, and these were used to refine the proposed mechanism for mining investment in South Africa. The proposed funding framework is aimed at encouraging interaction between mining entrepreneurs, government, and the investors to align goals and expectations when undertaking a mining investment.

Jan 1, 2012

By K. Andres

This paper presents the vibrating mill technology and summarizes the grinding principle of ultra fine grinding. In addition, a variety of operations is described and the benefits of these different operating modes? product size and efficiency are specified. A case study of an industrial application is presented to show the integration of vibrating mills into grinding circuits. The primary focus is the overall process scheme of this technology, the installation and operating costs, as well as the design parameters required for best performance. The vibrating mill can be used in a wide range of applications for process engineering duties. For a wide range of applications, from soft to extremely hard products, which require ultra fine grinding, surface activation or homogenization, the vibrating mill is well proven. Due to its easy operation, versatility and operation efficiency, the PALLA? vibrating mill gains in importance in the mineral processing industry. Keywords: Coal, comminution, grinding, mineral processing

Jan 1, 2010

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

The vast majority of the roughly 100 million rock anchors installed in mines in the USA each year use resin cartridges1. About 4.5 million of these bolts are installed using a mechanical shell in addition to the resin to create an active (pre-tensioned) bolt. Over 1 million of the bolts are passive cable bolts and typically have an effective grout length of 1.2 m, regardless of the cable length, which could be as long as 6 m. The successful performance of the resin grouted bolts depends on several parameters, including the annular gap between the bolt and hole wall, which should be relatively small, ideally from 3 mm to 5 mm. This requirement, combined with the high viscosity of the resin, produces a high back-pressure that can cause the bolt being installed to buckle or not be installed to standard. It is this back-pressure that limits the effective grout length with passive cable bolts and causes the mechanically anchored bolt failures (typically called ?spinners? where the mechanical shell does not anchor). This creates potentially unsafe conditions and wastes time and money. A purpose, built rig was used to mimic underground installations and record the back-pressures during full scale applications in the laboratory. This information was used, and is still being used, to reduce the failures and sub-standard installations by producing improved designs. In addition, a flow model was calibrated that can act qualitatively to estimate the back-pressures and can be used as a crude screening process before full scale prototypes are built and tested. To date, the results obtained have been used to stop the use of a mechanical shell due to the proven higher rate of failures. A new, improved mechanical shell is being field tested and another system is underdevelopment. The use of the rig is therefore ongoing to develop improved mechanical anchor systems. It is too early for real data; however, anecdotal evidence seems to indicate that significant improvements can and will be made.

Jan 1, 2011

By Stephen Yirenkyi

The mining industry remains the backbone of many economies in the developing world. Its resurgence in Ghana since 1989 was driven by the global paradigm which emphasizes private sector-led development as the engine of economic growth in developing countries. The historical importance of mining in the economic development of Ghana is evident in the country?s colonial name, Gold Coast (Akabzaa T. and Darimani A., 2001). Ghana earned $2.5 billion from mineral exports in 2007. 20,000 people are employed in large-scale mining whilst 500,000 are employed in the small-scale sector. Mining contributes about 7% of Ghana?s total corporate tax earnings, 41% of total exports, 12% of revenue collected by the Internal Revenue Service and 5% of Gross Domestic Product (Ghana Chamber of Mines, 2008). Gold dominates the mining sector and the country is Africa?s second largest gold producer after South Africa. Surface Mining, which refers to a method of extracting minerals from the earth by their removal from an open pit or borrows, requires a large tract of land for its operations (Wikipedia, 2008). There is therefore a continuous divergence of interest between land required for surface mining and other land uses such as farming and housing, among others. In recent years, surface mining has been promoted in many mining countries because of the following reasons: ?Cost considerations compared to underground mining; ?Safety considerations, compared to underground mining; ?Low grade ore which requires processing huge quantities; ?Location of the ore bodies; and ?Competition among gold producing countries for investors. This paper looks at the socio-economic impacts and challenges of surface mining by using Gold Fields Ghana Ltd. Tarkwa, Ghana as a case study. The company has a concession of about 208 sq km located in the heart of the Wassa communities in the Western Region of Ghana and undertakes surface mining like most of the other mining companies in the country. Gold Fields, Tarkwa mine produces 700,000 ounces of gold a year with the potential of increasing this output to 800,000 ounces after its current expansion programme. Some of the effects of surface mining identified were: 1. Relocation/Resettlement of host communities and its negative effects; 2. Disturbance to Flora and Fauna; 3. Disturbance to Sacred Places; 4. Land Degradation; 5. Noise and Air Pollution; and 6. Water Pollution. This paper sought to investigate the measures put in place by the government and the Gold Fields Ghana Ltd. to mitigate the above effects in order to ensure peaceful coexistence between the mining company and its host communities. It concludes that most mining companies presume the provision of socio-economic development in mining communities will lead to the company securing a social license to operate. This however is not true but rather effective community relations combined with socio-economic development. According to Gold Fields Ghana Ltds. model, this involves continuous community engagement, conflict resolution and comprehensive environmental monitoring programme which will all lead to effective community relations. The strategies to ensure socio-economic development involves community development programme, livelihood restoration programme and community training and employment. All these will then lead to sustainable development which will ensure the company?s social license to operate. Gold Fields? model is in line with the principles of responsible mining. With this model, the community feels they are part of the company and the social license of the company is guaranteed. Gold Fields? model, which has been tried and tested for the past five years, could serve as a template with suitable modification for local conditions for other mining countries where surface mines operate.

Jan 1, 2008

By N. C. J. Dempers, J. A. L. Parker, R. A. Wildenboer

More than half of global cobalt reserves are located in the Southern African Copperbelt, stretching over the northern tip of Zambia and southern area of the Democratic Republic of Congo. In these areas, cobalt is not typically produced as a primary product but as a byproduct of copper production. Ores from this region often contain uranium, which is readily leached under typical copper leach conditions and enters the process. Uranium does not pose a challenge to copper production, but it becomes a significant problem when it follows cobalt to the cobalt precipitation process and results in unacceptably high levels of U in the final Co product. This paper evaluates the existing process technologies that can be used to remove uranium from cobalt-bearing process streams, including phosphate precipitation and ion exchange. Advantages and disadvantages of the uranium removal processes are discussed, and important design considerations are highlighted.

Jan 1, 2023

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By B. Hart, B. K. Gorain, A. Chattopadhyay, S. Dimovc

This paper presents a detailed and systematic approach to metallurgy diagnostics using an integrated novel gold deportment technique for complex copper-gold and refractory gold ore bodies. This uantitative gold deportment for these complex ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Gold mostly occurs as "invisible gold" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulphides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Studies were initiated on various complex ore deposits and also on samples representing various process streams. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A systematic and holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies. Keywords: Integrated gold deportment, complex copper-gold ores, double refractory gold ores, carbonaceous matter, diagnostic metallurgy, preg-robbed surface gold

Jan 1, 2020

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By A. Pareek, V. S. Masampally, V. Runkana

Mineral processing plants, in general, consist of comminution and separation circuits. Rougher flotation is considered as the heart of the separation circuit with concentrate grade and mineral recovery being the key productivity and quality parameters that affect the downstream operations and profitability. Online prediction of these parameters can help improve process performance in real-time. Past efforts to predict flotation cell performance have focused on building physics-based or machinelearning (ML) based models. Although physics-based models are popular in process design applications, ML models are more appropriate for online monitoring, control and optimisation due to their lower computational requirements. Deep learning (DL) is gaining prominence nowadays for application in industrial operations where a large amount of data is available. We have developed a DL model based on long short-term memory (LSTM) neural networks to forecast the two key performance indicators (KPIs), namely, mineral recovery and concentrate grade in a mineral processing plant. Rougher feed characteristics such as mineral grade and particle size distribution, upstream measurable disturbances such as throughput of the comminution circuit and pulp density, and control variables such as aeration rate, pH, and collector addition rate are considered as explanatory variables to train the model. The model was tested with data from an industrial mineral processing plant. For real-time dynamic predictions, the trained model appropriately accounts for mismatch in measurement frequency of real-time process data and off-line laboratory analysis data. Such a time series model can be used as a state observer in model predictive control techniques for optimal control of unit operations in a mineral processing plant. Keywords: Mineral processing, flotation, time-series, dynamic modelling, deep learning

Jan 1, 2020

A mineralogical study was conducted on the feed (3.51 g/t Au and ~90 g/t Ag) and four leach residue samples (assaying 0.09 to 0.19 g/t Au and 30.0 to 61.5 g/t Ag) from the Pinos Altos silver-gold deposit in Mexico to determine the cause for gold and silver losses. A comprehensive mineralogical and analytical approach including fire assay, gravity pre-concentration, ore microscopy, mineral liberation analyser (MLA) and electron microprobe was used for the current study. Results showed that gold and silver lost in the leach residues occurred mainly as inclusions in quartz and silicates (accounting for over 80% for Au and 92% for Ag of the head assays, respectively), with a minor amount in iron oxide and other minerals. The amount of liberated gold and silver is negligible. Results also showed that gold and silver particles in leach residues are mainly ranged from 1 µm to 5 µm in size, which implies that ultrafine grinding is required to improve the recoveries of these two metals. Keywords: mineralogy, gold deportment, silver deportment, silver-gold ore, leach residue, recovery improvement.

Jan 1, 2009

By J. van Zyl Visser

The advancement in Information Technology has resulted in a change in workflow practice in our Mineral Resource Management (MRM) offices on the mines and at our corporate office. This paper discusses the AngloGold approach in defining an IT strategy for MRM, a brief overview of systems usage and benefits. AngloGold has gone through a transformation phase and has positioned itself as a world-class, low cost producer. To support this objective, an initiative has been launched to provide the MRM division with an integrated MRM technical suite of systems with support of a Management Information System. Technical systems for a tabular orebody are not freely available and hence it took AngloGold almost seven years and a significant amount of capital to develop an integrated suite of technical systems. AngloGold MRM IT adopted the typical Zachman framework (value chain) approach in the analysis process and formulated the final deliverable in terms of AngloGold’s strategy. Major benefits have been realized through the ability to change planning scenarios in a short period of time and hence be able to increase reserves and NPV. The development of MRIS, which will become the flagship in AngloGold’s portfolio of systems is in phase two and this system will allow AngloGold to publish Resources and Reserves as per SAMREC and the JORC Code at will. The availability of information at all levels of the operations has made making decisions easier and hence some specialized reports such as the Basic Mining Equation were developed from the Corporate Data warehouse and from the MRM reporting database. Decision Support Systems(DSS) such as Business Objects and Oracle Express are now being used to assist in the process. The decision to use Business Objects to replace SAS reporting as the core reporting tool has resulted in the empowerment of the user and major cost saving as far as the use of consultants to set up standard reports.

Jan 1, 2003

By N. Baloyi, P. Popoola, M. Tlotleng, S. L. Pityana

"The advantages of using Nb and Ti-Nb coatings for improving the hardness and corrosion resistance of Ti6Al4V were investigated. It has been reported that Ti6Al4V used in orthopaedic implants tends to release toxic Al and V ions into the surrounding tissue. Thin layers of Nb and Ti-Nb were deposited on Ti6Al4V substrates using a laser metal deposition technique. The deposited material was analysed using optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffraction. The corrosion behaviour of the deposited layers was investigated using a Metrohm Autolab PG Stat101 compact potentiostat at 25°C in simulated body fluid. A Vickers hardness system was used to study the mechanical properties. Both Nb and Ti-Nb coatings exhibited good metallurgical bonding with the substrate. The microstructure and the XRD analyses for the Nb system showed that the ??-Nb phase was most dominant, while the Ti-Nb system comprised a mixture of the ?? and ?? phases. The average hardness of the Ti6Al4V substrate was 350 HV0.3, with a slight increase for the Nb coating (363 HV0.3) and a much higher hardness from the Ti-Nb coating at 423 HV0.3. The corrosion results show that the deposited Nb was more corrosion-resistant in the solution than either the Ti6Al4V substrate or the Ti-Nb coating. IntroductionMetals such as CoCrMo, 316L stainless steel, and NiTi alloy are used for manufacturing biomedical implants because of their distinct properties, including low Young’s modulus and resistance to corrosion (Ryan, Pandit, and Apatsidis, 2006). These implants are required to remain in the body of the patient for many years. Due to a favourable combination of mechanical and corrosion properties, titanium (Ti) and its alloys have emerged as the material of choice for biomedical implants. Nevertheless, their use is not entirely without challenges. For example, in total hip replacement, surface degradation and release of metal debris from metal erosion caused by friction limit the service life of the implant (Oldani and Dominguez, 2012; Manivasagam, Dhinasekaran, and Rajamanickam, 2010). Ti6Al4V is generally regarded as the material of choice, but it has been found that over extended periods of time, the combination of surface corrosion and erosion releases toxic aluminium (Al) and vanadium (V) ions into the body (Khan, Williams, and Williams, 1996). This has led to the investigation of titanium alloys containing niobium (Nb), zirconium (Zr), tantalum (Ta), and molybdenum (Mo) as substitutes for the aluminium- and vanadium-containing Ti6Al4V (Okazaki et al., 1997)."

Apr 1, 2019

By A. Mainza, A. Mabentsela

A finite element model of a 5 m radius DC arc ilmenite furnace in idling mode was used to test the notion that the slag solidifies when it comes in to contact with colder pig iron, thus constituting the initial step in the formation of solid slag at the slag-pig iron interface. It was found that a slag that is 150°C hotter than the pig iron does not solidify at the interface. The 150°C temperature difference between the slag and pig iron is a result of solid slag at the slag-pig iron interface, not the other way around as suggested in the literature. Calculations show that the thickness of the frozen slag at the slag-pig iron interface is 1.7 cm for the furnace used. It is proposed that slag solidification begins with the slow co-current flow of molten slag and pig iron in the outer parts of the furnace. This provides enough time for molten slag to interact with molten pig iron without solidifying. As the reduction products form due to reduction of the slag by carbon in the pig iron, the slag solidifies. This approach negates the need for the slag to solidify by merely coming into contact with an inherently colder pig iron. Making use of a low thermal contact conductance between the slag and pig iron was found to be sufficient to numerically capture the presence of solid slag at the slag-pig iron interface and to preserve the 150C difference between the slag and pig iron phase.

Mar 30, 2023

By L. Cheng, Y. Liu, Z. Shen, H. Shang, Y. Li

The pre-concentration process of magnetic coarse particles can discharge waste rock or liberated gangue before milling, which is an effective means to reduce cost and increase the efficiency of the concentrator, but the weakly magnetic ore doesn’t have the effective separation method of coarse particle such as hematite, limonite, ilmenite and so on, Because the composite iron minerals contain both strong and weak magnetic elements, the pre-concentration process cannot be applied, or the existing pre-concentration process has problems of complicated configuration and high operation cost. By researching a new type of external magnetic separation technology, the pre-concentration process of composite iron ore was realised by single equipment, which can have a good recovery rate with simple arrangement. In this paper, the separation principle and structure characteristics of the external magnetic separator were researched, and the magnetic circuit characteristics of the external magnet were analysed. The laboratory tests of vanadium titanium magnetite were conducted, and the test results proved that the external magnetic separator can be applied for the pre-concentration process. The industrial application shows that a product of TFe 24.76% with 90.08% recovery, TiO2 10.10% with 91.78% recovery can be achieved from the feed of TFe 20.67%, TiO2 8.33%. Keywords: Coarse particle pre-concentration, composite iron ore, external magnet, magnetic separator

Jan 1, 2020

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021