Search Documents

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By Susan B. Bealko

Mining provides a large part of the energy and raw materials that feed this Nation's economy. Copper pipe, concrete, and window glass serve as well known examples of the reliance on minerals in modern society. Less appreciated, but as important, are the hundreds of mined commodities that are an integral and necessary part of everyday products, ranging from medicines and computers to carpet and paper. Coal is a major portion of the country's energy mix today, as it will likely continue to be in a future hydrogen-based economy. The domestic mining industry also provides strategic minerals that are important for the Nation's security. The processes to recover these mineral commodities are among the most demanding and complex in an industrial society, and this inherently dangerous industry has historically had the highest risks of fatality and injury. The mining industry has been undergoing some trying and challenging times because of the recent mine disasters in the coal fields. These events have been alarming in light of the strong and encouraging safety record that has characterized mining in the United States for most of the past decade. While mining communities deal with their grief, mine operators, government regulators, and other safety personnel, set about trying to determine why these fatalities occurred. Subsequently, the mining industry is currently experiencing changes in legislation at an unusually rapid pace. The most recent regulatory changes are the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) and the temporary emergency standard for mine seals. The new mine safety laws call on the nation's mines to adopt certain procedures and safety technologies immediately, or as soon as they become commercially available. Putting all the provisions in place from these new laws is a major undertaking, and will necessitate strong collaborations and partnerships among mine operators, manufacturers, regulatory and research agencies, labor unions, and community groups. It is against this background that Prevention through Design (PtD) components for the Mining Sector are recommended.

Jan 1, 2008

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By G. B. Shea

The accident experience of the California petroleum industry for 1927 was characterized by a decrease it .the number of fatalities. The year closed with a total of 41 fatal accidents, as compared with a total of 54 for the preceding year. 3 In percentage, the figure for 1927 represents a decrease of 24 per cent from that of 1926 and evidences the promising results of organized safety work, in which the industry in California has taken an absorbing interest. The percentage of decrease for 1927 is the largest recorded in any one year since the compilation of the fatality record in the California petroleum industry was begun. Although good progress has been made during the past few years, much remains to be done to reduce still further the human and economic waste caused by accidents. This review is intended to show the employee, as well as the employer, the proximate and contributing cause of accidents. To increase the value of the report, preventive measures in various instances are suggested, on the theory that accidents of a similar nature will occur unless remedial action in taken to remove the cause.

Jan 1, 1928

By Oliver Bowles

The following discussion of waste rock utilization constitutes the fifth paper of the current series of reports on lime- plant quarry problems . As here tofore lime manufacturers are invited to cooperate to the fullest extent by supplementing the Bureau's information with the results of their own experiences and observations . Waste utilization is the key to success in many enterprises , and with a broader knowledge of this branch of the lime industry more economical operation is made possible . Your assistance in compiling additional data on this subject is solicited , and such assistance may be rendered by writing answers to the questions on the final page of this report .

Apr 1, 1923

By Scott Turner

To be successful , human exertion employed for the creation of value requires power and heat ; the ability to produce concentrated power in great quantities has resulted in the relatively recent industrial development that is so profoundly affecting the world . In our commercial history , we have advanced through several stages in the selection of the most suitable fuels , continuously striving to increase the flexibility and range of energy- transmission . The easy distribution of light , power and heat is the leading factor in the decentralization of industry which promises to correct some of the serious evils that have followed in the footsteps of our commercial development . The distribution of fuel in quantity in so convenient a form and with such an attractive reliability- factor as can be had with gas , meets the modern conception of efficient service . Natural gas has been used in this country for more than a century, but recently it has attained a prominence far in excess of anything known in its earlier history. We may consider that we are now getting into our real stride in the utilization of our natural- gas resources . : In a country like the United States , wherein we are accustomed to mammoth achievements , we may be inclined to accept casually the noteworthy technical and economic advances which have resulted in the expansion of natural- gas distribution . About three years ago , the transmission of natural gas a distance of more than 250 miles from its source was first accomplished , and this was really a noteworthy engineering feat . Today , this useful commodity is being transported twice that distance , and lines are being laid which will carry gas more than 900 miles from the points of occurrence . Let us not take such outstanding improvements too much as a matter of course ; the industry should be congratulated on its long steps forward .

Oct 1, 1930

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

[ ]

Jan 1, 2012

By B. T. Brady

Laboratory measurements by the Bureau of Mines indicate that failure in dry rock specimens measuring approximately 13 cm in length is preceded by tilt anomalies lasting a few milliseconds. The tilt behavior is qualitatively similar to that reported to precede earthquakes. Test results suggest that the time duration of this tilt anomaly for laboratory specimens of this length is independent of rock type, in agreement with theoretical predictions and other experimental data on rock failures including earthquakes.

Jan 1, 1975

By F. J. Gallagher

The purpose of this circular is to present information on the construction and use of reinforced rubber-jacketed tubing and insulating air-line couplings in coal mines where Airdox is used for breaking coal in order to eliminate, insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.

Sep 1, 1949

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By C. E. Wethered

This paper describing the mining methods employed by the Federal Mining and Smelting Co., operating the Morning mine at Mullan, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The daily tonnage produced at the Morning mine, including that mined by leasers, is 1,100 tons. Mine run of ore will average 9.1 per cent lead, 5.8 per cent zinc, and 4.4 ounces silver per ton. A stull set and fill method of mining is employed.

Jan 1, 1930

By Arthur L. Murray

"Putting safety over , " using the accepted meaning of the word " Safety " as the elimination of personal injury , resolves itself into the prevention or disassociation of a combination of two distinct circumstances . Opportunity for accidents is afforded by conditions that are likely to cause injuries , but such injuries are effected only when the human body is placed in a position to be injured . As will be discussed later , in mining , as in most other industries , the degree of safety experienced depends upon the disassociation of these two circumstances , first , by making working conditions as free from hazards as possible , thus affording the minimum opportunity for accidents to occur , and secondly , the training of employees to recognize dangerous conditions and adopt measures to protect themselves and their fellow employees against injury . The responsibility for preventing accidents rests upon every person employed in an industry from the directing head down through the individual workers , and the safety of that industry will be proportionate to the extent that each member appreciates and accepts his individual responsibility . Hence , safety becomes decidedly a personal equation . Whether the personal equation will be so applied as to result in the greatest freedom from accidents , however , depends largely upon the initiative of those directing the industry . Putting safety over in a small mine presents the personal equation in a more intensified manner than the same endeavor in a large mine . Large mines , owing to their size and financial standing, can usually main ta in and support an effective safety organization with one or more directors who devote all their time to the supervision of safety work . Most small mines with a limited number of employees and limited capital can not afford and are not justified in supporting a paid safety organization , and must depend upon the close cooperation of their working force in maintaining safe working conditions . On the other hand , if proper supervision is exercised the small mine has in some respects advantages not afforded by the large mine . The limited workings in a small mine should afford less opportunities for dangerous conditions to arise and permits more frequent inspection of the entire mine . The small working force permits more latitude in the selection of employees known or believed to be either safe workers or amenable to safety educational work. Likewise , a small working force facilitates the carrying on of safety educational work and allows a closer personal contact between the superintendent and his employees .

Mar 1, 1923

By H. N. Smith

IN 1944 the Congress passed the Synthetic Liquid Fuels Act that authorized the Secretary of the Interior, acting through the Federal Bureau of Mines, to conduct basic research and construct and operate demonstration plants to produce synthetic liquid fuels from coal, oil shale, and other substances. As a basis for the oil shale investigations to be undertaken in this country, the progress of foreign countries in developing and using oil shale as a source of liquid fuels was studied by the technical missions of the Federal Bureau of Mines. Oil shale mines, retorting plants, and refineries were visited; geological information on the nature and occurrence of the foreign oil shales was obtained; and samples of the oil shales were collected where possible. Samples collected by these missions or acquired by other means came from Australia, Brazil, Canada, France, Manchuria (China) , New Zealand, Scot-land, Spain, Sweden, Thailand, and Union of South Africa. These countries represent a large part of the locations where oil shale developments have taken place. The major omissions are the Estonian, German, and Russian developments.

Jan 1, 1959

By Ronald F. Balazik

The introduction of "high-tech" materials such as new polymer composites presents significant competitive challenges and opportunities in conventional mineral markets. Moreover, rapid advances in materials science are critical to the resolution of important economic and strategic issues, including national competitiveness and import dependence. This Bureau of Mines study examines the displacement of conventional nonfuel mineral materials by certain new materials, specifically advanced plastics and ceramics. Analyses of substitution by plastics are conducted for five major U.S. industrial sectors: motor vehicle manufacturing, aerospace applications, building and construction, packaging, and heavy machinery production. Based on interviews with more than 60 scientists, executives, and other professionals engaged in materials development and sales, forecasts of substitution by plastics during the 1990's are made for aluminum, steel, and glass. In addition to these forecasts, study findings identify key factors that will influence the emergence of advanced materials in the next decade.

Jan 1, 1987

By Kenneth E. Hjelmstad

The U.S. Bureau of Mines (USBM) has developed an electromagnetic (EM) fire warning alarm sys-tem for underground mines. The system generates a magnetic field for through-the-earth signal trans-mission to microreceivers carried by individual miners. EM fields can induce electric currents in metallic conductors; if an EM transmitting antenna and an electric blasting cap array are too close, the field could induce a current in the blasting array and cause an unintentional initiation of the electric detonators. The USBM conducted tests that define the safe and unsafe regions for using electric detonators near the transmitting antenna of the warning alarm system. The minimum safe distance between a transmitting antenna and a blasting array is the distance where the induced electrical current in the blasting array is 50 mA, which is the safe current level specified in Federal mine safety regulations. Tests indicate that at transmitting power levels of 100-and 1,000-W, separation distances of 9 and 21 m, respectively, were required. These distances are small compared with the dimensions of a mine. Thus, the tests indicate that, with proper placement of the transmitting antenna, the warning system can be used safely in the proximity of blasting arrays.

Jan 1, 2010

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993