Search Documents

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By S. A. Gustavson, H. E. Olund

This report has been prepared to review the history of the Premium Price Plan for copper, lead, and zinc, which was in operation from February 1, 1942, to June 30, 1947. It includes various charts and tables comparing costs and production data, and data on exploration premiums that were included in the Plan during the last year of its operation.

Jan 1, 1950

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By B. Dimitriades

Data on smog-forming reactivities of exhaust aldehydes are scarce. Such data were obtained by irradiating in a smog chamber typical exhaust aldehydes, individually and in exhaustlike mixtures. Observed reactivity manifestations were rate of nitrogen dioxide formation (RNO2) and yields of oxidant, peroxyacetyl nitrate, and formaldehyde. Results showed that exhaust aldehydes vary widely in reactivity. Formaldehyde showed high RNO2 reactivity but low oxidant yield; benzaldehyde, [m]-, and [p]-tolualdehyde were totally unreactive when irradiated individually; [o]-tolualdehyde was reactive. In mixtures, benzaldehyde manifested reactivity in terms of peroxybenzoyl nitrate yield. Exhaust aldehydes as a group are judged to be as reactive as the exhaust olefin group. The importance of the aldehyde contribution to exhaust reactivity and methods for assessing such contribution are discussed.

Jan 1, 1971

By A. R. Taylor

Low-temperature heat capacities of cesium chloride (7° - 300° K) and cesium iodide (13° - 300°K) were measured with an adiabatic calorimeter. The heat-capacity measurements were analyzed graphically to determine smooth values of heat capacity, entropy, enthalpy function, and free-energy function at 10° K intervals and at 273.15° and 298.15° K.

Jan 1, 1963

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By Charlie Wyche

The principal minerals produced in the Dominion of Fiji in 1982 were unrefined gold, silver, and tellurium. The combined value of these commodities was about $16 million,2 representing over 85% of the total value of mineral output. Cement, sand and gravel, and quarry products were the other minerals produced in Fiji. Despite the small part played by minerals in Fiji's economy, exploration on land and in the coastal areas was carried out by several international mining companies representing Australian, British, Canadian, West German, and U.S. interests. At the end of 1982, 30 prospecting licenses covering 2,300 square kilometers were issued. Most licenses were for copper, zinc, gold, and silver. Total expenditure on mineral exploration was $3.5 million.

Jan 1, 1984

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

By D. Harrington, C. W. Owings

"The belief is now fairly general among the coal-mining people of the United States that one of the most effective methods of preventing wide-spread coalmine .explosions is that of introducing rock-dust into coal mines to reduce the inflammability or explosibility of dusts found on mine surfaces. Notwithstanding this belief it is improbable that even a small fraction of 1 per cent of the coal mines of the United States are at all adequately protected by rock-dust; in a survey made in the summer, and fall of 1927 it was found that but 463 out of more than 7,000 operating bituminous and lignitic coal mines were using rock-dust at all, and that few if any of the 463 were fully or adequately protected by rock-dusting.Inspections of a large number of mines through the United States by Bureau of Mines safety division field men have failed to reveal a single adequately rock-dusted mine, Yet there is no doubt that many of the owners and operators believed their properties to be fully protected by rock-dust against the much-feared hazard of widespread explosion. Two of the most disastrous explosions of recent years occurred at properties where the owners were definitely of the belief that the rock-dusting done had made the mines immune to widespread explosion involving coal-dust. In both instances it was found that although some rock-dusting had been done, the mines were more nearly 1 per cent than 100 per cent rock-dusted.This condition as to inefficiency or insufficiency of rock-dusting in the coal mines of the United States is almost universal, and unless our mining men awaken to its, dangers, the disaster record of the coal-mining industry is much more likely to become worse than better. During the fiscal year ended June 30, 1928, the attention of the safety division of the United States Bureau of Mines was called to. 22 explosions With 320 fatalities in bituminous coal mines of the United States; and of the 22 explosions there were 10 with 258 fatalities in mines that were listed as having used rock-dust; upon investigation it was found that as usual the rock-dusting had been anything but comprehensive or adequate. It is probable that in a very few instances last year the relatively small amount of rock-dusting stopped the .extension of the explosion and thus prevented further expansion of the death list. In general, however, the explosions occurred in a part of the mine that had not been rock-dusted - and right here is the crux of the failure or probable failure of present-day rock-dusting in the United States, There should be no part of any bituminous or coal mine in which all of the exposed surfaces (roof, ribs, and floor) have not been thoroughly rock-dusted and kept thoroughly rock-dusted. In other words, all exposed surfaces of all accessible places in bituminous and lignitic coal mines should be kept covered with rock-dust so that the combined rock-dust coal-dust mixture at all times and in all places has less than 35 or 40 per cent combustible matter, The only exception to this rule is that surfaces which are wet (and this does not mean merely damp) need not be rock-dusted. However, a mine opening may have several inches of water on the floor and yet have much explosive dust on the ribs and roof above the water; in such places the ribs and roof should be kept rock-dusted, irrespective of the wetness of the floor."

Nov 1, 1928

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By L. J. Froisland

The U.S. Bureau of Mines conducted laboratory studies on sulfuric acid (H2S04) digestion of alunite [KA13(S04)2(OH)6] as a means for treating domestic deposits of this mineral. Digesting alunite ore in boiling H2S04 at concentrations of 88-wt-pct acid or higher breaks down the alunite and permits a convenient separation of potassium and aluminum. The digestion reaction is a complex sulfation reaction occurring in two stages. In this reaction, the potassium component extracts into the H2S04 for eventual recovery as potassium sulfate k2s04 in a separate unit operation. Aluminum is left as acid-insoluble aluminum sulfate [A12(S04)a], which can be extracted by a 95° C water leach. Additional purification of AI2(S04)a produced in this study is needed to meet cell-grade alumina (Al202) purity specifications. Extraction and separation of potassium and aluminum from the alunite ore were consistently above 90 pct.

Jan 1, 1989

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By P. B. Lorenz

Wettability measurements and laboratory waterflood tests were compared under a wide variety of conditions. Experiments were conducted with synthetic and natural crude oils, treated and untreated outcrop and oilfield sandstone cores, and synthetic brines with and without caustic, detergent, or phosphate additives. Measurements were made on equilibrated and unequilibrated systems at 77° and 150° F. Wettability was evaluated by the Bureau of Mines method from capillary pressure curves determined with a centrifuge. The waterflood data were fitted by empirical curves; the parameters of the curves characterize primary and subordinate production and also give the ultimate oil recovery. Results showed that wettability measurements at 77° F were useful predictors of recovery efficiency in waterflood tests run at both temperatures. Oil recovery in the early stages of waterflooding increased with increasing water wettability; however, the ultimate recovery was highest at a slightly oil-wet condition. The oil displaced at highest speed in the centrifuge was correlated with ultimate recovery in waterflood tests. Chemical additives to the brine sometimes lowered wettability and also sometimes improved waterflood recovery, but wettability and recovery were not correlated with additives present. The effect of additives on recovery in waterflooding was best seen in water-oil ratio curves.

Jan 1, 1974

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968