Search Documents

By D. R. Tesarik, R. W. McKibbin

Material properties affecting slope stability were measured in a large 50-year-old, partially consolidated rockdump located in an active open-pit mine. Field tests included single-ring infiltration and density. In addition, a nuclear depth-moisture gauge was used to measure water content in six stainless-steel-cased drill holes on the crest and an upper bench of the rock dump. Precipitation, evaporation, wind speed and direction, and temperature data were collected at a weather station installed on the dump’s crest. Laboratory tests included particle-size distribution, specific gravity, Atterberg limits, and water content. By measuring material properties of a rock dump presumed to be stable, the safety of miners working on or at the toe of old rock dumps constructed of similar material and located in a similar climate can be assessed.

Jan 1, 1999

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By Arthur L. Murray

The first thought in the case of an accident or contagious disease is naturally that aroused by our humane instinct , how serious is the case and will the person recover ? The economic effects of such cases , owing to their many ramifications , are seldom realized either by those directing mining operations or those engaged in the labor of producing . This paper is based on the accident experience of the State of Utah and the number of cases of two well known preventable diseases , typhoid fever and smallpox , in that State for the fiscal years 1917-1918 , 1918-1919 , 1919-1920 , and 1920-1921 . The data and figures presented are from coal -mining camps only . W. W. Adams , mine- accident statistician of the bureau, contributed valuable corrections and suggestions . The economic results of accidents are considered first , and those of the two preventable diseases later .

Apr 1, 1922

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982

By J. M. Oestreich

Supercritical water (sew) Is being tested for commercial use 1n several organic extraction systems but little work has been done on the extraction of metals from minerals. This lack of information prompted Bureau of Hines (BOM) research into the sew treatment of minerals. As a result, this research project is intended to serve mainly as a starting point for further experimentation. A simple flow-through reactor was built out of high pressure tubing and used to treat minerals with SCU at 400? C and 3500 to 7000 psi. The research produced four main conclusions: (1) carbonates of copper, iron, and lead convert to oxides; (2) most iron minerals showed alteration to oxides with some iron dissolution; (3) valuable trace elements including nickel, chromium, and others leached to some extent from sea minerals along with some calcium, iron, silicon, and sulfur; and (4) treatment of sulfides extracted elemental sulfur and resulted in several alteration reactions, though with the exception of cinnabar and the iron bearing minerals, the metals in sulfides were mainly insoluble. Surface alterations on many of the minerals show significant changes have occurred in the minerals even when only minor extractions were detected. These surface effects may be very important when used in conjunction with flotation processes since the sew treatment may selectively enhance or suppress a mineral&apos;s floatability.

Jan 1, 1989

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 8, 1977

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By E. J. Harris

Data obtained from mine ventilation pressure and quantity surveys are required to accurately diagnose ventilation problems, project future air quantity needs, and to locate conditions adversely affecting the efficiency of a mine ventilation system. A method for making mine ventilation pressure surveys with aneroid altimeters was presented in Bureau of Mines Information Circular 7809, and a description of field calculation technique is presented. This report supplements Information Circular 7809 by developing the information obtained during a mine ventilation pressure survey into a single equation suitable, with appropriate modification, for use with desk-top calculators and digital computers. The equation can be used to calculate the ventilation pres sure from the base station to any underground station, or between any two underground stations, and can be programed for semiautomatic sequential calculation using a desk-top calculator. An example of application to a programed desk-top calculator is provided in the appendix.

Jan 1, 1973

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d&apos;Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d&apos;Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d&apos;Alene mining region, Shoshone County, Idaho. Production and other stat is tics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d?Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By Mary S. Esfandiary

This list of organizations that conduct research and development programs on coal has been compiled by the Bureau of Mines with the thought that such a directory may provide a useful guide to worldwide research efforts in the areas designated and may facilitate communication between organizations with similar interests. This list includes government, university, private, and commercial organizations. Many of these groups are conducting comparatively modest but often particularly interesting or specialized investigations. The areas of investigation have been defined in a broad manner--these include analysis and constitution, mining and geology, preparation, combustion, briquetting, high- and low-temperature carbonization, gasification, hydrogenation, Fischer-Tropsch, and health and safety. In some instances such information is not available, but the names of the organizations themselves often indicate immediate arias of interest. Special publications issued by and describing the work of each organization have been cited, when known; almost all of the organizations also publish results of their investigations in the technical press. Several foreign technical and trade publications that include such information and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. This list is not complete. Information that would improve coverage and/or accuracy will be welcomed by the Bureau of Mines.

Jan 1, 1961

By David R. Flinn

This Bureau of Mines report describes methods to electrodeposit erosion-resistant titanium diboride coatings from molten alkali metal borate baths at 900° C. These coatings have been shown to be highly resistant to material loss during impingement with high-velocity alumina and silicon carbide powders, and they show promise as protective coatings to reduce metal loss in erosive chemical environments, such as coal gasification systems. The most erosion-resistant coatings were prepared on nickel, Inconel, and molybdenum from an electrolyte containing LiBO2, NaBO2, Na2Ti03, and TiO2. The best coatings were deposited at current densities of [~]20 ma/cm2, using titanium or titanium diboride anodes. Erosion-resistant coatings were shown to exhibit (1) a high degree of crystallographic orientation along the (100) or (110) planes, (2) a chromium impurity level of less than 3 pct, and (3) a uniform, smooth, consolidated surface appearance when viewed under a microscope or by scanning electron microscopy. Optical spectroscopic studies of the molten electrolyte suggest that the lower valent (+3) titanium ion predominates in the baths.

Jan 1, 1979