Search Documents

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By Michael D. Fenton

The very modest-sized mineral industry of Afghanistan was burdened for another year with problems of internal strife occassioned by the presence of Soviet armed forces. Despite this, production of the few traditional commodities continued, and the mineral industry moved to develop additional mines and plants for both traditional and new products with considerable technical and construction assistance from the U.S.S.R. Among the limited range of mineral commodities for which production was reported, there were no startling changes between 1984 and 1985. Production of both coal and natural gas advanced only slightly, despite substantially higher 5-year plan goals, and cement output was down marginally. Probably the most significant development in 1985 was the Possibility that mine and/or smelter production of copper was initiated during the year.

Jan 1, 1987

By Robert W. Freedman

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By H. D. Jacobs

The Bureau of Mines undertook a research program to insure an adequate supply of iron raw materials for future iron and steel making needs. A sample was obtained of oxidized taconite from the western Mesabi Range in Minnesota, and the metallurgical response of the taconite to beneficiation by a process that included selective flocculation-desliming-cationic flotation was evaluated. The sample contained 35.3 pct iron and represented approximately 2 billion tons of crude material. Selective flocculation and flotation were evaluated in a pilot plant with a feed rate of 900 Ib/hr. Concentrates averaging 61.7 pet iron and 5.1 pet silica were obtained, with an accompanying iron recovery of 67.2 pet. About 83 pct of the process water requirements were reclaimed from the slime and froth tailing and then recycled.

Jan 1, 1980

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968

NIOSH recommends that exposures to respirable coal mine dust be limited to 1 mg/m3 as a TWA concentration for up to 10 hr/day during a 40-hr workweek, measured according to current MSHA methods (see Section 5.1 and Appendix J). NIOSH recommends that sampling be conducted with a device that operates in accordance with the NIOSH accuracy criteria [Busch 1977; Busch and Taylor 198 11 and the international definition of respirable dust [ACGIH 1994; CEN 1993; IS01993; Soderholm 1991a,b; 1989].* The REL represents the upper limit of exposure for each worker during each work shift. For single, full-shift samples used to determine noncompliance, NIOSH recommends that MSHA make no upward adjustment of the REL to account for measurement uncertainties [NIOSH 1994c] (see also Section 5.6.2). NIOSH further recommends that all reasonable efforts be made to reduce exposures to respirable coal mine dust below the REL through the use of engineering controls and work practices.

Jan 1, 1997

By Thomas R. Bur

This method of performing general transformations by use of Eulerian angles greatly reduces the time required for the determination of values for the elastic compliance constants (sij), elastic stiffness constants (cij ), Young's modulus, shear modulus, or Poisson's ratio for any orientation the cartesian coordinate system in an anisotropic material.

Jan 1, 1969

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By Robert J. Hundhausen

This report describes Bureau of Mines investigations of a low-grade scheelite-bearing granodiorite intrusive situated on Henderson Creek, Granite County, Mont. The intrusive is in a narrow, V-shaped valley at the head of extensive placer workings. Since May 1943 the H. & R. Mines Co. of Portland, Oreg., has recovered scheelite sand and gold from the placer workings. A modified Yuba, 4?cubic foot bucket dredge was used in the operation. By February 1947 this operation had recovered and marketed over 215,000 pounds of scheelite concentrates containing 63 percent WO3. The scheelite in the placer was found to be derived principally from erosion of the granodiorite intrusive. The intrusive is one of a series of four similar, dikelike masses of granodiorite whose outcrops are aligned along a 10-mile zone of weakness trending N. 60° E. The intrusive has a triangular outcrop exposed over an area of 57 acres. Trenching and sampling by the Bureau of Mines demonstrated that scheelite is sparsely distributed throughout the granodiorite. This work delimited the outcrop of the intrusive and indicated a large submarginal reserve of low-grade tungsten mineralization. The deposit is ideally suited for exploitation by large-scale, open-pit mining operations; it would be easily available in a national emergency. Additional exploration would be necessary, however, before large-scale production plans could be made efficiently or accurately.

Jan 1, 1949

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground metal/nonmetal and stone mines by state during 1990-2001. Table 10 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 12 fires occurred in 11 states; 5 of the fires caused 5 injuries. The yearly average was one fire and 0.42 injury. Five fires with two injuries occurred at metal mines, five fires with two injuries occurred at nonmetal mines, and two fires with one injury occurred at stone mines. None of the fires involved contractors. The Ewhr value was 58 x 106 hr (Irr = 0.017), and the LWD value was 75. Nevada had the most fires (two fires and no injuries). Ohio, New Mexico, Missouri, South Dakota, and Idaho each had one fire with one injury. Of these states, Missouri had the highest injury risk rate value (In = 0.25). Table 11, partly illustrated in figure 5, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the six time periods. The number of fire injuries and employees' working hours decreased during all of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 12-17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables related to fires for 1990-2001. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995