Search Documents

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By Raymond L. Lowrie

For many years it has been considered that an average of 50 percent of the coal in the deposits exploited has been recovered. Owing to many changes in mining methods during the past two decades, this study was initiated to obtain an up-to-date measurement of recovery percentage and thus establish part of the basis from which presently recoverable reserves may be estimated. Recovery percentages were determined within mined areas of 200 underground coal mines. These comprised a statistical sample selected to be representative of operating mines in relation to their significance to depletion of reserves. The results ranged from 29 to 91 percent and averaged 57.0 ± 1.7 percent (95-percent confidence limit). Six factors were identified mathematically as significantly affecting recovery percentages: (1) Pillaring system, (2) top rock and conditions, (3) bottom rock and conditions, (4) marketability, (5) coalbed thickness, and (6) productivity. Skill and attitude of mine operators toward recovery, although not measured, were probable factors. Five other variables that were tested did not show any significant relationship with recovery percentages. Also, five mining equipment features were identified, through discussions with mine officials, as affecting adversely recovery percentage at some mines.

Jan 1, 1968

By J. E. Doo1ey

To process and use the heavy ends of petroleum effectively, the development of suitable separation and characterization procedures not currently available was required. A systematic procedure was developed by the Bureau of Mines using such techniques as isothermal and molecular distillation, chemical treatment, silica-alumina gel chromatography, gel permeation chromatography, and spectrometry. Using these techniques, the Bureau achieved a detailed separation and characterization of a 370° to 535° C distillate from Gach Saran, Iran, crude oil. Such a systematic procedure and the semiquantitative data resulting therefrom should be of value in selecting feedstocks and in optimizing petroleum processing operations.

Jan 1, 1973

By J. M. Singer

Quenching distances for flames of methane-coal dust mixtures were determined with air and oxygen-enriched air. Coals used were Pittsburgh, Sewell, and Pocahontas No.3. Quenching distances were greater for flames of hybrid mixtures of coal dust and methane than for methane flames of corresponding stoichiometry. From the data of quenching distances and methane-coal dust concentrations was calculated the quenching equivalence, which is the increase in coal dust concentration required to maintain a given quenching distance value as the methane concentration decreases. These equivalences could be useful in identifying hazardous methane-coal dust mixtures in mines.

Jan 1, 1966

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1965 and 1966 (calendar years), except for breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for safe use in underground mines.

Jan 1, 1968

By A. R. Taylor

The Bureau of Mines has determined the heat capacity and enthalpy values for beryllium sulfate (BeS04) throughout the temperature ranges of 10° to 300° K in an adiabatic calorimeter, and 350° to 860° K in a Bunsen-type ice calorimter, The heat-capacity data were extrapolated to 0° K, and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were reported at 10-degree intervals between 0° and 300° K. The method of least squares was used to fit the enthalpy data with an algebraic equation. The equation also was used to calculate values of heat capacity, entropy, enthalpy function, and free-energy function at 50-degree intervals between 300° and 900° K.

Jan 1, 1963

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By L. C. George, J. W. Jensen

A new system for precisely counterbalancing and measuring vapor pressure operates by servomechanical principles . It was developed with the objective of determining the vapor - pressure equations of metal halides . The system is isolated from the vapor - pressure bulb by a diaphragm transducer that signals a pressure regulator to null any pressure difference that is detected . Pressure measurement and readout are continuously performed by a servomanometer , accurate to ±0.003 cm Hg for the range of 0.1 to 200 cm Hg . High response rate and sensitivity are obtained . Methods of use are described , and results for CdC1 and PbC1 , in agreement with data of other investigators , are given as examples .

Jan 1, 1964

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By G. W. Jones

The operation of combustion engines of various types at high altitudes and other combustion processes at reduced pressures have made it desirable to determine limits of flammabilities -under these conditions. Experiments carried out by the Bureau of Mines have shown that although natural gas-air mixtures become more difficult to ignite as the pressure is reduced below atmospheric, with a suitable source of ignition the limits of flammability are as wide at 175 mm mercury absolute as they are at atmospheric pressure.

Jan 1, 1949

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By H. B. Humphrey, F. E. Cash

The Birmingham coal-mining district of Alabama has many local physical conditions that contribute largely to the proble of preventing coalmine fatalities . Coal : nes of Alabama have been under the supervision of the State mine inspector since 1892 , and reports have been made with increasing completeness since that time . The U. S. Bureau of Mines has maintained a station of the safety division in the district since 1912 to cooperate with operators and the State in the advancement of safety in mining . A description of conditions in regard to fatal accidents as they have been and as they now are in Alabama , compared with the entire United States , will indicate the progress that has been made and that should still be made in reducing fatal mine accidents .

Sep 1, 1930

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,' CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2' 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2' 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1967 and 1968 (calendar years), except breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for use in underground mines.

Jan 1, 1970

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956