Search Documents

By C. Lorimer Colburn, Spencer P. Howell

"Numerous accidents are still being reported that have resulted from the delayed explosions in drill holes. Some of these accidents have boon due to retarded burning of the fuse, causing the charge to explode after the miners had returned to the face, but the majority have been caused by the minors drilling or picking into unexploded explosives, either in unexploded bolas or in broken rock. Although the industry has been cautioned by the Bureau of Mines, manufacturers of explosives, and other agencies regarding the care that is necessary in the handling of explosives, yet reports of these accidents are still being received and many of the accidents are fatal, They occur in spite of the best efforts of the mine officials and men, but many of those that have been reported could have been avoided if the following precautions had been observed:Misfires should not be approached even for the purpose of inspection until three hours have elapsed if fuse was used, and ten minutes if electric detonators or electric igniters were used. These are minimum recommendations. It would be preferable to allow a longer time, for fuses have been known to hang fire for twelve hours."

Aug 1, 1920

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Emory Smith

The Victorville cement plant of the Southwestern Portland Cement Co. is located about 1 mile from the city of Victorville, Calif. Two transcontinental railway systems, the Atchison, Topeka & Santa Fe, and the Southern Pacific Railroad, afford shipped facilities. The plant is modern and well kept, as the officials, especially the higher operating officials, take pride in the appearance of the place. Dust has been practically eliminated by the installation of dust collectors and wet grinding. The plant has a rated capacity of 5,000 barrels of cement daily.

Jan 1, 1929

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

By A. L. Engel

The sample of ore on which the work described in this paper was done came from Mina Oriente, Carrizal Bajo, Provincia de Atacama, Chile, South America, and was sent at the request of the Chil.ean Government through the Foreign Minerals Division of the Bureau of Mines. This ore had been tested locally for treatment by flotation and cyanidation without satisfactory results. An additional difficulty was the absence of water near the ore deposits, so that in any treatment method considered the water requirements would have to be very low. It was desired to develop a practical method of recovering the gold and, if possible, the copper in the area. No data of previous investigations were made available. The sample received was mostly quartz, highly brecciated, with limonite and hematite in the fractures. Copper occurred as malachite and azurite, also in the fracture s and to a slight extent as a stain in the quartz. Some fine-grained pyrite with a little arsenopyrite occurred within the quartz. An occasional grain of chalcopyrite was observed. No free gold was seen during examinations of the ore, but amalgamation indicated that some was present.

Jan 1, 1949

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By Allen D. Look

In the prevention of accidents in milling operations, the proper installation and guarding of electrical and mechanical equipment, safe clearances, good housekeeping, adequate fire protection, adequate ventilation, dust and fume control, and good illumination, as well as safe practices, are essential. In the new concentrator of the Magna Copper Co., Superior, Ariz., many safeguards were incorporated and safe practices instituted to minimize accident hazards. The purpose of this paper is to describe some of these features and practices.

Jan 1, 1951

By Wing G. Agnew

The drilling and bit-sharpening practice in the southwest Wisconsin zinc district generally conforms to the procedure described herein, except at very small properties, where drill steel is sharpened by hand. Though hot milling of rock-drill bits is practiced in South Africa on some of the large-scale operations, it is seldom seen at American minus in any form. Because of the simplicity and low cost of the equipment, it was thought that a brief description might prove interesting to same of the operators in ether districts who do not have enough steel to sharpen to warrant equipping an elaborate sharpening shop.

Jan 1, 1936

By J. D. Spagnola

The Bureau of Mines conducted research to obtain comparative data on the extent of reduction of galena and sphalerite with molecular hydrogen and with hydrogen from the thermal cracking of ammonia and methane at various time intervals. Galena reductions of 95 to 99 percent were obtained with H2 and with decomposed NH3 while reductions of 70 to 80 percent were obtained with cracked CH4? Sphalerite reductions of 99 percent were obtained at 1,000° C with Hz and with decomposed NBs; however, complete volatilization of the free zinc from the remaining concentrate and the subsequent recombination of zinc and sulfur vapors resulted. A promoted iron catalyst brought about a decrease of 100° C in the temperature required for complete decomposition of ammonia. It was found that H2S retards NB3 decomposition and that nitrogen retards the reduction of galena by H2? A mixture of N2 and He in about the same ratio as that obtained by the thermal cracking of NBs gave about 15 percent less reduction of galena than was obtained with decomposed NB3; this indicates that a portion of the hydrogen obtained by NBs decomposition is in an active form.

Jan 1, 1965

By L. L. NAUS, R. D. Currie

Hazards in connection with the use of compressed-air jets for ventilating gassy mines are given little consideration by most mine officials largely because compressed air is considered the safest means of transmitting power for operating various types of mining machinery, and the inherent dangers in its use for this purpose are virtually negligible . The installation of compressed-air lines in coal mines leads to the utilization of compressed air for ventilating working places , with the result that , although the primary ventilation systems may be adequate to meet existing needs , proper conduction of normal ventilation has been neglected , so the working faces receive only a small amount ofthe total air circulated through the mine . Reliance in part on compressed air or other auxiliary means for ventilation is always attended by danger that gas will accumulate , due to intermittent operation , and the tendency is to operate auxiliary schemes only. during the working shift ( or possibly only part of the shift ) and to dispense with them during off- shifts or at times during the working shift when gas may accumulate because of lack of ventilation . When the men come on shift the auxiliary ventilating device often may be started without a preliminary examination of the working place , or .. the examination may be made sometime before the oncoming shift arrives , the gas being allowed to accumulate in the meantime. This may result in uncontrolled movement of a body of gas if proper precautions are not taken . Several mine explosions have been caused by the movement of a known body of gas by compressed air into the haulageway, where it was ignited by an arc from a passing locomotive . This danger is more pronounced where supervision is lax .

Aug 1, 1937

By M. M. Tilman

The Bureau of Mines conducted research into the dispersion strengthening of lead by the coprecipitation method. Commercially available reagents in water solutions were reacted to form homogeneous precipitates of lead and aluminum compounds. The resulting precipitates were roasted to oxides and reduced in hydrogen to form mixtures of lead powder and alumina. The powders were isostatically pressed into billets which were extruded into rods. The rods were rolled into strip to provide material for testing. Alloys containing 0.5, 1, 2, and 3 nominal volume-percent A1203 were tested in short-time tensile tests and in tensile creep tests. An alloy of Pb-3 volume-percent A1203 exhibited an average tensile strength of 8,570 psi after rolling to 75-percent reduction at 125° C but had no measurable elongation. Alloys of lower A1203 content provided a better compromise between tensile strength and ductility. For example, an alloy of Pb-0.5 volume-percent A1203 had an average tensile strength of 6,590 psi with 9-percent elongation after rolling to 75-percent reduction at 125° C. Creep rates of dispersion-strengthened Pb-A1203 alloys were below 1 percent in 10,000 hours at stresses of 2,000 to 4,000 psi.

Jan 1, 1971

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By Geo S. Rice

"Three men lost their lives in the Black Diamond Coal Mine near Seattle, Wash., recently while wearing oxygen breathing apparatus. The press dispatches stated that these men lost their lives while practicing with the apparatus. Later reports stated that the men died while attempting to make a trip 1200 feet down a 25 degree slope which was filled with black damp, in order to measure the amount of water that had accumulated at the bottom of the mine, and the trip was attempted with oxygen in the tanks of the apparatus with dials indicating only 45 minutes supply. The oxygen in the tank was used up and the men therefore lost their lives from a deficiency of air to breathe.In spite of all the education and training done by the Government to prevent accidents, men are prone occasionally to take unnecessary chances. Every piece of apparatus, no matter how perfect, has its limitations. The Government, through the agency of the Bureau of Mines, has trained many thousands of miners in the use of mine rescue apparatus. The training has been given to all miners who requested it, and the Bureau has gone to the extreme of urging miners to join the rescue and first-aid classes. In spite of all the efforts of the Government, men occasionally attempt the impossible."

Jul 1, 1920

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c&apos;,ov~-lo.pe;t by tL1e &apos;.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.&apos;l. :.-,,- #?,n c-noot&apos;fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(&apos; the c8n:xcity oi&apos; the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn&apos;rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o&apos;q7r ir.:,l soon t ire:. the oyernt or]

Jan 1, 1938

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c&apos;,ov~-lo.pe;t by tL1e &apos;.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.&apos;l. :.-,,- #?,n c-noot&apos;fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(&apos; the c8n:xcity oi&apos; the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn&apos;rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o&apos;q7r ir.:,l soon t ire:. the oyernt or, ]

Jan 1, 1938

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945