Search Documents

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988

By R. V. Mrazek

The heat of formation of vanadium trichloride was determined at 298.15° K. Measurements were made in a solution calorimeter in which an aqueous hydrochloric acid-potassium dichromate solvent was employed. Data are presented for the heats of solution of vanadium trichloride and the vanadium trioxide "backup" compound, and for appropriate dilution reactions needed to preserve stoichiometry. The resulting heat of formation of vanadium trichioride (VCI3) at 298.15° K was found to be ?H°298.15° K = -138.89 ±0.37 kcal/g mole.

Jan 1, 1968

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By Joan Weinberg

Real gross national product (GNP) grew at a seasonally adjusted annual rate of 2.2% in the third quarter, down from a revised 3.0% in the second quarter, according to preliminary data from the U.S. Department of Commerce (table 1). The slowdown in the rate of growth was attributed to the summer drought, a larger trade deficit, and a decline in Federal spending for defense. Exports slowed from the second quarter, as the dollar, compared with other industrial country currencies, edged up. Imports of both consumer goods and capital goods rose sharply, with consumers buying more foreign cars, computers, and electrical machinery. Although net exports of goods and services deteriorated slightly from the second quarter, the U.S. trade position continues to be much improved from 1987 and first quarter, 1988. Business spending for new plant and equipment rose at a 4.6% pace, well below that recorded earlier in the year. The 3.5% increase in consumer expenditure was accounted for mainly by nondurable goods and services; expenditure for durable goods--those products lasting more than 3 years--rose only 0.4%. Inflation, as measured by the fixed-weighted GNP price index, rose at an annual rate of 4.9% in the third quarter. Prices rose slightly less than they had in the second quarter, when inflation reached a 6-year high. In September, 1988, the President signed a U.S.-Canada free trade agreement (FTA) which will eliminate all tariffs and most nontariff barriers between the two countries by 1999, thereby creating the world's largest open market. In 1987, U.S.-Canadian bilateral trade totaled $161 billion. The expansion of trade is expected to generate 5% higher growth for Canada and up to 1 % higher growth for the United States by the end of the century. The higher growth for the United States translates into an estimated 750,000 jobs, and $2.4 billion in exports. Canadian parliamentary approval of the agreement is still required before the treaty can take effect. The debate in Parliament is continuing, and the issue is not expected to be resolved until after the November 21 election.

Jan 1, 1988

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

By G. R. Palmer

Using a fluidized, countercurrent multiple-compartment ion-exchange (MCIX) column previously developed by the Bureau of Mines, Bureau researchers have successfully extracted uranium from a simulated acidic in situ leach liquor that contained 150 ppm U30s? This successful demonstration of the MCIX system is reported, and the effects of varying the operating conditions on the performance of the system are also examined. Operating the MCIX system with a flow rate of 15 gpm/ft2 and an aqueous-to-resin flow ratio of 200:1, more than 90 percent of the uranium Has extracted, and a resin containing approximately 28 grams U308 per liter was produced. The absorption column used to investigate the operating variables was approximately 18 feet long with a 2-inch ID and was divided into compartments that were 1 foot long.

Jan 1, 1980

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By Elton L. Litchfield

The techniques for direct initiation of detonation, developed by the Bureau of Mines, have been applied to gaseous mixtures of oxygen with methane, 'thane, propane, butane, or hexane. An exploding wire was used as the initiation source to determine minimum stored electrical energies required to effect detonation of mixtures between one-half and two times the stoichiometric fuel ratios. Detonations were obtained in the most easily initiated mixtures of ethane, propane, butane, and hexane for initiation energies between 24 and 33 joules at 1 atm and 28-43 joules at 0.5 atm initial pressure. Methane mixtures, at 1 atm, were not observed to detonate when initiated with up to 484 joules.

Jan 1, 1966

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for control-ling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for control-ling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979