Search Documents

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature of the group IVB, VB, and VIR elements. This review was utilized in the Bureau's research to provide erosion-, abrasion-, and corrosion-resistant coatings for valve components used in coal gasification units. This report attempts to bring together the many CVD references that have been published since 1966. Each of the group IVB, VB, and VLB metal coatings were reviewed, and some of their preparation methods, uses, and properties are given. A total of 160 references were found for the nine elements. Isotope separation, stronger steels, solar absorbers, alloys, superconductors, optical fibers, and coatings to increase the life of materials are some of the new uses for CVD.

Jan 1, 1979

In 2004, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 891 underground (6.2%) and 13,587 surface (93.8%) mining operations.

Sep 1, 2007

By R. R. Sayers

There is probably no industry , trade , or art in which mercury is used but what has produced some cases of mercury poisoning . This is true of the mining and smelting of mercury , where the hazard has long been recognized . When the ore contains free mercury or the more soluble salts , and when the workings are underground and are poorly ventilated , cases occur , but there are a far greater number of cases among the employees about the reduction works . 3 In 1863 William V. Wells visited the mines at Almaden , * Spain , which were worked by convicts . He reported that the men at the furnaces suffered severely , being able to work only about one week out of four , when it was necessary to transfer them to places where the exposure was less . He states that "pale cadaverous faces and leaden eyes are consequences of even these short periods . " Mercury , like lead , when absorbed in small amounts at intervals , as daily, over an extended period of time will result in symptoms of poisoning . This is due to the fact that the mercury is eliminated from the body more slowly than it is absorbed . The frequency and severity of cases of mercury poisoning are far less with modern methods of mining and recovery of the metal than formerly . However , further reduction is possible and much can be done by both the workmen and the operators by following the proper precautionary measures , some of which are described in this chapter .

May 1, 1922

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal, (2) to upgrade marginal coals through effective preparation, and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the seventh of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Floyd County, KY., which comprises parts of the Paintsville, Prestonsburg, Harold, Hindman, and Pikeville quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all avail-able data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Robert H. Peters

This report presents findings from a Bureau of Mines study on barriers that may prevent miners from correcting and avoiding groundfall hazards. Such barriers stem from four basic types of problems: (1) inability to recognize groundfall hazards, (2) inability to correct groundfall hazards, (3) lack of motivation to search for groundfall hazards, and (4) lack of motivation to correct groundfall hazards. Data are presented that summarize the views of miners, section supervisors, and mine inspectors about the contribution of these barriers to groundfall accidents and what they think should be done to reduce the frequency of injuries sustained by falls of roof and rib. The report also includes a summary of miners' responses concerning their recent experiences with groundfall accidents, along with industrywide statistics on accidents and injuries caused by ground falls in underground coal mines.

Jan 1, 1987

By T. R. Jolley

This publication describes the control of fires in inactive coal deposits in the Western United States, including Alaska by the Bureau of Mines. Material presented should contribute to a better understanding of the purpose, process, and benefits of the program. Forty fires were extinguished or controlled in the Western United States and Alaska from 1948 to 1958 under a national program directed by the Bureau's Health and Safety activity. Thirty-five fires were controlled by smothering; three were controlled by the isolation method; and two were extinguished by removing the burning coal, smothering it with incombustible material, and backfilling the fire zone. The fire-control projects were distributed as follows: Alaska 2, Arizona 1, Colorado 9, Montana 9, New Mexico 4, Utah 2, and Wyoming 13. The total cost of the 40 fires extinguished or controlled was $1,203,957. Of this cost, 12.8 percent was engineering and administrative and 87.2 percent was contractual services.

Jan 1, 1959

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By J. R. Cobble

Dissolution of chalcopyrite with acidified ferric sulfate produces a sulfur layer on the unreacted chalcopyrite surface that interferes with further dissolution. The U.S. Bureau of Mines has developed a process to improve the leaching kinetics of these types of diffusion-controlled systems. The system features the Bureau-developed turbomill, an attrition grinder that scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be operated continuously at any temperature up to the boiling point of the leaching agent. This method is a hydrometallurgical alternative to chalcopyrite smelter technology and eliminates sulfur dioxide emission problems with its associated costs. Batch testing at 900 C with the chalcopyrite-ferric sulfate system resulted in copper extraction exceeding 99 pct. At an optimal energy consumption of 1,520 kW· hjst, 95 pct of the copper was extracted. The pregnant liquor was clarified and tested for typical solvent-extraction recovery of the copper. Two-stage extraction and two-stage stripping recovered 96 pct of the copper in an electrolyte suitable for copper electrowinning.

Jan 1, 1993

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By W. J. Boone, Will E. DeVaney, Lowell Stroud

This report is the fifth in a series presenting equilibrium vapor - liquid data for helium- bearing natural gases . It covers a 0.41 - mole - percent - helium natural gas that may be processed in the Department of the Interior's longrange helium conservation program . A Bureau of Mines phase equilibrium apparatus was used to obtain 139 samples of equilibrium vapor and liquid phases at 85 experimental conditions at temperatures from 0 ° to -299 ° F and at pressures from 100 to 500 psia . An appendix covers phase data at 100 , 200 , and 300 psia and at temperatures from -125 ° to -275 ° F for the dehydrated gas containing its original concentration ( 0.2 mole - percent ) of carbon dioxide , and the effect of a preliminary hydrocarbon trap upon subsequent vapor - liquid compositions .

Jan 1, 1964

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By John W. Kopp

Stemming is used in blasting operations to help contain explosive gases as long as possible. Stemming can reduce airblast, improve fragmentation, and reduce the chances of hot explosive gases igniting methane and dust explosions in underground mines. Stemming is required in underground coal mines but is generally not used in underground metal and nonmetal mines. Some underground metal and nonmetal mines are classified as gassy and can require special blasting procedures such as the use of stemming to minsure the safety of miners. The types and amounts of stemming material that are desirable in underground metal and nonmetal mine blasting to ensure good or improved fragmentation while containing the hot gases are largely unknown. This Bureau of Mines research examined the effectiveness of differing lengths of stemming by measuring stemming ejection times as related to burden movement. With properly stemmed blasts, stemming is contained until some burden movement has occurred. Test blasts at two surface limestone quarries were evaluated using high-speed photography. For the conditions of these tests, a stemming length of at least 26 charge diameters was found to prevent premature stemming ejection. In tests with stemming lengths of 16 charge diameters, the stemming was effective but there was early venting of hot gases through fractures in the rock. Further testing with other rock types, hole diameters, explosive types, and stemming materials as they affect incendivity is recommended.

Jan 1, 1987

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

By Howard P. Hamlin, John W. Sweeney

Shales from 14 locations in Indiana were sampled , tested , and evaluated to determine feasibility of producing lightweight aggregates by rotary - kiln and sintering methods . Sampling procedures and the geology of the significant shale units are discussed . Preliminary testing was conducted in a muffle furnace , and continuous tests were made in a 16 - inch by 14 - foot rotary kiln . The aggregate weighed 37.0 to 47.2 pounds per cubic foot . Concrete cubes employing the aggregate were tested to determine the qualities of the concrete . Compressive strength of the concrete using seven bags of cement per cubic yard , after autoclave curing for 6 hours , ranged from 3,600 to 5,850 pounds per square inch . Four samples made suitable lightweight aggregate in the laboratory rotary kiln . Four samples tested by sintering methods made unsatisfactory aggregate .

Jan 1, 1965

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964