Search Documents

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company. ]

Jan 1, 1938

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company.]

Jan 1, 1938

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1968-69. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Elmer W. Pehrson

The recent establishment of an official price of 64.64 cents per ounce for silver by the President's order of December 21, 1933, has provoked discussion as to the effects of this move on the various metal-mining industries. To assist those of the mineral industry who are interested in this problem, the Bureau of Mines presents the following analysis of basic statistical data concerning; the relation of the silver price to the value of copper ores mined in the United States. The term "copper ore" as used herein includes all ores in which copper is the most abundant base metal paid for. In 1928, this class of ore contributed 98 percent of the total copper output of the United States.

Jan 1, 1934

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By J. S. Hansen

In support of its objective to conserve mineral resources by minimizing premature failure of materials, the Bureau of Mines conducted a cooperative study with the U.S. Department of Energy on the erosion and abrasion resistance of hard materials for valves in coal conversion systems. This report describes a newly developed erosion-testing apparatus and presents data on the erosion resistance of over 200 materials. Erosion resistance of most metals was comparatively low. In contrast, ceramics and cermets such as B4C, WC, SiC, Si3N4, and TiB2, when fabricated to minimize porosity, displayed greater than five times the erosion resistance of metals. Coatings such as boron diffused into Mo and WC, chemical-vapor-deposited TiCN, and electrodeposited TiB2 were highly erosion resistant if applied in thicknesses ranging from 60 to 75 µm. Erosion resistance of cemented carbides was inversely related to metal binder content.

Jan 1, 1979

By R. R. Sayers

Carbon monoxide poisoning, as usually encountered, is an acute condition resulting from breathing atmospheres containing that gas. It is characterized clinically by headache, dizziness, weakness in the legs, increased respiration at first which later becomes irregular and depressed, collapse, unconciousness, and death; anatomically it is characterized by temporary changes in the red blood cells due to the combination of carbon monoxide with hemoglobin, and, in prolonged severe exposures, degenerative changes in various tissues of the body, especially those of the central nervous system. No race or nationality is immune or has a, special tolerance for carbon monoxide. From data at hand, it is known that both sexes are about equally susceptible. All ages are affected, but small percentages seem to have a more deleterious effect upon young animals and this is possibly true of children. Exercise, high temperature and humidity, and low oxygen content of en atmosphere increase the degree of poisoning for a certain concentration of carbon monoxide. Anything that lowers the physical fitness of a man, such as illness, overwork, or excesses of any kind, exaggerates the effects. More cases of poisoning from carbon monoxide occur in coal mines in the cold months of the year, because explosions take place more frequently during that period, also in homes where gas is used for beating purposes, and in garages from accumulation of automobile exhaust gases due to poor ventilation.

Jan 1, 1923

By Michael D. Dunn

The Bureau of Mines evaluated a quartz schist formation within the Blue Joint Wilderness Study Area which was identified as having a "high potential" for copper-silver-cobalt-barium resources. Stratiform and remobilized copper occurs near, and bedded barite within, the study area. In addition, the black to gray Proterozoic quartz schist may correlate with the Yellowjacket Formation which contains cobalt-copper-gold-silver deposits at Blackbird, ID, about 30 miles to the south. Eighty soil and 43 rock samples collected across the quartz schist formation were analyzed for gold, silver, copper, cobalt, and barium. During the reconnaissance and sampling, particular attention was given to looking for malachite (copper carbonate) and erythrite (cobalt arsenate, also known as "cobalt bloom"). The sample analyses and geology in this localized area do not provide enough evidence to support the "high potential" designation for copper-silver-cobalt resources. Barium potential still appears high, however.

Jan 1, 1987

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interiors This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941.£1 No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1949

By Calvin J. Konya

Overloaded blastholes and insufficient stemming are major factors in flyrock accidents at surface metal and non-metal mines, Accurate measurement of blasthole depth, stemming height, and water depth would reduce the overload and the probability of blow-out, flyrock, excessive ground vibration, and airblast. Problems result because current measuring systems are inaccurate and often difficult to used A literature survey determined measurement techniques and blasting parameters prior to 1970. Similar data were gathered for current practices in 11 iron mines, 30 copper mines, and 92 quarries. Most operations used a cloth tape to measure borehole depth and stemming height; approximately 10% of the operations had dry blastholes. Alternate measurement techniques were evaluated and discussed. Candidate measuring techniques with best potential for improvement over the present weighted tape method are disposable tapes or string chains, automated readout tapes, modified sludge level indicators and acoustic resonance methods.

Jan 1, 1981

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By Robert W. Geehan

The Bureau of Mines has been developing deposits of critical and essential minerals in the United States since 1939. A preliminary examination of the Union lead mine was made in November 1944 and January 1945 by W. T. Benson, a Bureau of Mines engineer, who recommended development by diamond drilling. The Bureau conducted a drilling project at the mine from February 12 to May 16, 1947. The property is in sec.12, T. 17'N., R. 19 E., Mount Diablo Base and Meridian, in. southern Washoe County, Nev., about 15 miles south of Reno. The Union lead mane, also known 4s the Commonwealth mine, has been an intermittent producer of zinc-lead-silver ore since 1860. During World War II, ore was shipped to smelter& near: salt Lake City, Utah. The Bureau drilled 21 diamond-drill holes having a total length of 1,549 feet and 20 long percussion-drill holes with a total length of 359 feet. The program was designed to test for horizontal and vertical extensions of the ore body and to prospect for parallel ore bodies. As a result of this program, extensions of the ore zone were established, but no parallel ore-bearing structures were found. The areas drilled were limited by drill sites available.

Jan 1, 1950

By F. R. McDonald

The proton NMR spectra of 32 pyridines in two solvents, carbon tetrachloride and benzene-d6, are presented. The chemical-shift and differential-shift values are correlated with the substitutent position and with the solvent media. The ring protons and the protons on alkyl substituents are tabulated. The paramagnetic shift of the protons adjacent to the nitrogen is discussed, and a proposed structure for the pyridine-benzene complex that is consistent with the observed anomalous paramagnetic shift is presented. The utility of the data in the identification of pyridine compounds found in shale-oil naphtha is demonstrated.

Jan 1, 1971

By Edward L. McHugh

Twelve properties in the Riverside Mountains have moderate to high potential, for silver, gold, copper, and molybdenum. Six properties in the Big Maria Mountains have moderate potential for zinc, lead, copper, silver, iron ore, and limestone. The Big Maria Mountains also have occurrences of building stone. Four properties in or near the study area have low-grade gold-silver-copper resources totalling more than 300 thousand tons (270,000 t). An estimated 29 million tons (26 million t) of limestone and dolomite, and 620,000 long tons (630,000 t) of iron ore are in the Big Maria Mountains section of the study area. INTRODUCTION The Big Maria Mountains Wilderness Study Area covers about 50,538 acres (20,453 ha) near the Colorado River in eastern Riverside County, California (fig. 1). The study includes portions of both the Big Maria and Riverside Mountains. It lies north of Blythe, California and south of California Highway 62 in the Mojave Desert province of the California Desert Conservation Area. The study area consists of two mountain ranges surrounded mostly by broad alluvial slopes or bajadas. It extends for 25 mi (40 km) from the Riverside Mountains on the north, to the south end of the elongate Big Maria Mountains.

Jan 1, 1982

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By O. C. Blade

Diesel fuel is being used in greater volume than ever before in the United States. During 1950 railroads used 43 percent of the total volume of Diesel fuel sold, smelters, mines, and manufacturing plants used about 13 percent, highway vehicles such as trucks and busses, and equipment such as tractors and bulldozers accounted for approximately 20 percent, about 12 percent was used by water craft, and the remaining 12 percent by gas and electric utilities, the military forces, and oil companies. These figures were calculated from data issued by the Bureau of Mines. 2/ Comparable figures for 1951 and for 1952 to date are not available, but recent information indicates that well over 11,000,000 barrels of Diesel fuel per month are produced by the country's refineries. 3/ More information on this increasingly important type of engine fuel is needed by the petroleum industry, engine manufacturers, and consumers, particularly on the grades and qualities of the Diesel fuels being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of Diesel fuel oil produced in refineries in this country.

Jan 1, 1952

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire of the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire f the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940