Search Documents

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By Shih-Chi Chang

[An exploratory research is done on untreated coal 1v- using&apos; x-ray crnctinn techniques. Comparison is made on diffraction data before And pct Pr n-tiAne is pressurized (n the coal samples. Although, only ? qualificative -1; t s obtained, the FoIIowing Statement r :&apos; n untreated teal seem- There are other materials in cost. They are accumilated in !e ,r rc r, cin? the microseoric layered structure of coal. 7"P partial graph r :r a&apos; o., «&apos; the i&apos;pr1 cart o ! in cna1 assumes varclor, r,rie&apos;,r: r in&apos;is. R nr ?-&apos;c,.r1&apos;ed I n coal is helm ;n the micrornre s&apos;??ste^ o&apos; c, .:l an&apos; t rr i, ,o <.~i:&apos;epee of Ion(4inc to carton h« x-ray tit If raction me.:SUr&apos;rientq. :t?e me r &apos; nP in r^icropores assumes no structure themselves at room tempera¬FLre. ;inally, some of the other materials in coal are in the form of }vrlrited crystallites and they have anisotropic pro&apos;th hnt&apos;1? in the lavers.]

Jan 1, 2012

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau&apos;s annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer&apos;s claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By Arthur V. Petty

In Bureau of Mines research on recycling chrome-containing refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated. By means of dry magnetic separation on minus 6-mesh crushed wastes, a concentrate was produced. After minor adjustments to the particle size distribution, full-size refractory brick were dry-pressed by a commercial producer and fired to 1,450° and 1,730° C. Standard testing procedures were used to determine the cold-crushing strength, modulus of rupture at 25°, 1,300°, and 1,500° C, hot load, thermal shock resistance, thermal expansion, and slag resistance. Optical and electron microscopy were used to determine grain-bonding mechanisms, and energy-dispersive analysis of X-rays was used to determine elemental distribution. The test results indicate that the beneficiated material could be used to produce a refractory product suitable for moderate-temperature applications.

Jan 1, 1982

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner&apos;s safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual&apos;s air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982