Search Documents

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By Cathy Aimone-Martin, Frank Achuff

The New Mexico Department of Transportation (NMDOT) and the Federal Highway Administration (FHWA) have let a contract to Sierra Blanca Constructors for a design / build contract along 38 miles US 70 in Lincoln County, New Mexico. The project will improve safety of travel along the corridor and facilitate the adopted economic development goals of the state. Proposed improvements include widening the existing highway from two lanes to four lanes, providing left turn lane options at selected locations, improving access for businesses and residences, aesthetically enhancing retaining walls, improving storm drainage and replacing the existing pavement with a 30 year mechanistic imperialistic perpetual pavement design. The US 70 Hondo Valley highway project is situated in a narrow valley with steep limestone walls, passes along a Scenic Byway and numerous historic ranching communities with structures that date back three centuries. The scope of work included requirements to monitor and mitigate blasting, noise, and vibrations. The contract was very presumptive with regard to blasting design and procedures. These included visual impact mitigation to treat and stabilize slope cuts, the Migratory Bird Treaty Act protecting roosting and nesting birds from airblast, and the protection of historic and cultural features such as acequias, wells, and structures. Public involvement affecting the rock blasting design has come from citizen task forces and committees concerned with highwall aesthetics and preserving the scenic byway and cultural resources. Constraints placed on the blasting program from agencies and the communities are often at odds. For instance, blasting must produce stable yet natural-looking walls to preserve aesthetics. Restrictions have been placed on pre-splitting and smooth-wall blasting yet safe slope are of the highest priority. This paper presents details of the design/build process undertaken by the contractors to conduct blast rock in an environmentally sensitive region. Blast designs consistent with good construction practices and used to comply with the many federal and state highway stipulations are described.

Jan 1, 2004

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Michael Wieland

Work-principle computations for explosions underwater or in rock reveal the way the thermodynamic characteristics of surrounding material influence the resulting shock and heave. To reach total thermodynamic equilibrium under such transitory dynamic circumstances, reactions must quickly readjust to changing circumstances, which works for molecular (military) explosives where the fuel and oxidizer type atoms are originally in close proximity. For non-molecular mixtures with their dispersed zones of oxidizer or fuel, in particle or droplet form, there are numerous unproductive collisions, increasing the wait time required to reach chemical equilibrium. Underwater test data for molecular explosives compare rather well with the shock and heave resolved from the work-principal model, while the non-molecular explosives normally used in mining tend to yield a noticeable discrepancy. Years ago, it was recognized that the underwater shock was lower than expected and the heave was higher than expected for ammonium nitrate fuel oil (ANFO), though their resultant sum for the total work was roughly what was expected. When the readjustment of thermodynamic equilibrium warrants quicker chemistry than occurs in underwater or rock shooting, the time-retarded chemistry reduces the shock and raises the heave within the surrounding material without reducing the total work, unless the reaction retardation is quite severe. This technical complication in reality is a nonequilibrium issue that is difficult to resolve with just thermodynamics, though a rational set of transformation factors is formulated herein to represent those circumstances.

Jan 1, 2008

By Paul Worsey, Gillian Worsey

The basic blasting class at Missouri S&T blast in the quarry at the experimental mine in preparation for the International Intercollegiate Mining (Mucking) Competition in April 2014.

Jan 1, 2015

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014

By Michael Weaver, Dale Ramsey

Description of Project: The National Gateway Clearance Initiative is an improvement program to achieve a minimum of 21 feet of vertical clearance along CSX Transportation Inc’s (CSX) rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets.

Jan 1, 2014

The quiet banks of the Maumee River in Toledo, Ohio, received a wake-up call July 16 as two smokestacks in the Marina District were leveled with dynamite. B&B Wrecking, Inc. of Cleveland contracted the project with the city to bring down the twin stacks, both measuring over 250 feet tall. The structures were part of the Toledo Edison Steam Plant and were erected nearly a hundred years ago. A week’s worth of preparation went into final planning, drilling and loading holes with over 80 pounds of explosives. The felling went precisely as planned as onlookers cheered as the stacks were reduced to rubble.

Jan 1, 2015

By Walter Voglauer, Elisabeth Zechmeister

Description of Project: The four photos show a chimney blasting operation in Vienna’s district of Floridsdorf on May 4 2011. The blasting was done with two types of charges. An internal charge provided a force of blast which resulted in 135 single electrical blasting caps initiated detonations on the basic ensured the straight collapse of the chimney. The preparation work was done by reserve force military engineers. The series of photos were shot by Elisabeth Zechmeister. She works in the Austrian DOD but not as a professional photographer; much more she did all activities in her spare time.

Jan 1, 2013

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By Alain Duchesne, Dominique Fonfrede, Alan Broca

The technique involves the removal, in one piece, of an unwanted concrete pile section, exploiting the principle of crack propagation induced using gas pressure. The device, or pod, is made of a container in which an over-pressure is generated. After a predetermined time delay of 72 hours, gas and pressure are produced by the reaction between a calcium base chemical and water.

Jan 1, 2012

By Benjamin Cebrian

Metallurgical testing at Cobre Las Cruces prior to production at the mill was done with overburden gossan. Some of that test gossan was a very fine material, wet by the water conditions at the bottom of the pit. When processed and stored wet at the fines material 3000 tonne (3307 tons) silo, this material cemented in a very unusual manner.

Jan 1, 2010

By M. Gebhardt, J. Johnson, S. Rosenthal

The use of presplitting applications in an underground mine setting is a method of reducing overbreak in the rib and back when blasting occurs. Presplitting performed at the Underground Mine Education Center (UMEC) on Montana Technological University’s campus in Butte, Montana showed a dramatic decrease in the amount of overbreak incurred in the blasting process. Application of the presplitting technique occurred after presplitting presentations at ISEE in San Antonio. Presplit testing consisted of drilling perimeter holes closer together than production holes and loading perimeter holes with a combination of specialized presplit explosive and packaged emulsion with electronic detonator initiation. The ideology was to shoot the perimeter row first, to create a fracture around the perimeter, so when the main production round is shot there is less shock exerted on the surrounding walls due to the pre-fractured perimeter rock. For the test performed, the back ended up with 83% of total holes resulting in half barrels representing a remarkable result. The right rib ended up with one half barrel visible before muck was removed while the left rib did not have any half barrels visible due to a clay seam being in very close vicinity to the perimeter row. The first test blast was a great start encouraging future work on presplitting applications in the UMEC. Additional testing will continue with different combinations of perimeter hole spacing, the addition of a buffer row along the ribs, and varying loading techniques to determine the most effective presplit method for the rock type of the UMEC. Detailed test results and loading configurations will be provided in the paper.

Jan 1, 2024

By Braden Schmidt

The following full paper will go into the products, techniques and people who work in the avalanche control industry giving insight to the other members of the ISEE an overview of the niche blasting that is Avalanche Control.

Feb 1, 2020

By Debra Satkowiak, Ronald Thomas

The Institute of Makers of Explosives (IME), a non-profit safety and security organization founded in 1913, is known for its industry best practices, Safety Library Publications (SLP), some of which have been incorporated into rules by regulatory agencies. The IME developed the first commercial storage, quantity distance (Q/D) table titled “The American Table of Distances” (ATD). It was developed by IME’s legacy association in 1910 and was originally based on observations of structural damage from 117 accidental explosions involving small to very large amounts of explosives, primarily dynamite and black powder. In 1930, the IME published a book, compiled by Ralph Assheton, called the “History of Explosions on Which the American Table of Distances was Based”. The distance in feet in the ATD were founded on the measurements at which inhabited buildings sustained substantial structural damage from the accidental detonation of explosives. For example, minor damage such as window glass breakage and the “shaking down” of plaster was not considered substantial structural damage. Other damage to property that was readily repairable was also not considered “substantial.” It was concluded that unless some integral portion of the building was damaged, the occupants would not be subjected to serious risks.

Jan 1, 2017

By Lance McAnnuff

Whatever system is devised to control noise and ground vibration from blasting operations must present an effective compromise between the rights of the individual to be undisturbed by the actions of others, and the necessity for society, the whole of the population individually and collectively, to have the services and the products of commerce, industry and transportation along with the relaxation of recreational and cultural pursuits, all at a price within the means of the same society. One of the first jurisdictions in North America to attempt to quantify acceptable environmental limits for specific blasting operations was Ontario, Canada’s largest and most populous province. A process for development of guidelines applicable only to quarries and strip-mining operations was begun in 1974 and culminated with their inclusion in a “Model By-Law” published by the Ontario Ministry of the Environment in August 1978. This paper examines the process of development of the final guideline document and its application over the last 25 years. While acknowledging that the published guidelines for air blast and ground vibration control have provided a useful and generally workable framework for the purposes of land use planning and complaint or damage claim reduction, a number of flaws, weaknesses and misinterpretations connected with their application are identified. Recommendations for amendment of the controversial items are submitted with a view to making these and potentially similar guidelines in other jurisdictions, more acceptable to both government and industry.

Jan 1, 2004

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Tristan Worsey, John Henchion, Nathan Rouse, Yannick Lauras

"This paper presents an approach used to plan and evaluate drill and blast trials for a mine that currently mechanically excavates in-situ rock. The document presents the approach used to plan the trials, the key performance indicators (KPIs) that were necessary to evaluate the mining methods, the test matrix used during the trials, and the results of the trials. The trials, which occurred as part of an overall drill to mill optimization project at this site, helped to evaluate various blast designs using fragmentation results,drilling and blasting costs, and downstream costs. This project was unique in that (1) drill and blast methods were trialed on multiple rock types and various bench heights using a range of blasthole diameters and powder factors and (2) the load and haul costs were evaluated using a range of loading equipment, from 66 tonne (73 ton) excavators up to 250 tonne (276 ton) excavators. A ten year net cost financial evaluation of the material extraction alternatives was also prepared for the site management. Ultimately, the process of evaluating the drill and blast trials helped the management decide whether to continue extracting using mechanical methods or to introduce drill and blast methods to extract the rock."

Jan 1, 2017

By William. J. Birch, Catherine. E. Johnson, Robert Farnfield

Rocks and other materials can be characterized by their elastic properties. However, seismic velocities represent a more practical set of physical properties for seismic methods. Seismic velocities define the speed at which various elastic deformations propagate through different rock types. Seismic velocities for a given material can be expressed explicitly in terms of their elastic properties. It is widely accepted that the peak particle velocity and associated frequency of ground motion are important parameters for determining a safety criterion to minimise the potential for both damage to structures as well as nuisance to people. Whilst the key considerations are the blast design parameters, the seismic velocity is important as particle velocity is dependent in part on the powder factor [blasting ratio] which in turn is found to be dependent on the seismic velocity.

Feb 6, 2023