Search Documents

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By Urs Peuker, Thomas Mütze, Thomas Leißner, Inga Osbahr

"Mining in the Ore Mountains (Germany) has taken place for hundreds of years and in several stages. Each stage produced its typical tailing. According to the former state of the art of the processing much valuables could not be extracted. This was caused by complex interlocking of the minerals, low grades, or by upgrading processes not sensitive enough for small particle sizes. Thus the processing of these fractions was uneconomically. Modern technical possibilities and rising metal prices bring these tailings disposals into focus for the processing of strategic metals. Mining disposals can be classified in heaps with coarse, low grade rock, which did not undergo a processing, slags and fly ash from smelting, and tailing disposals from mineral processing. The latter is under investigation to integrate them into a geographic information system. The mineral processing of the material will be part of the database besides information about geographic location, structure, amount of valuables, and details of ownership of the heap. The tailings disposals are composed of coarse, low grade, interlocked particles from density separation processes, medium size particles, which are tailings from flotation, and fines with liberated valuables, which did not undergo flotation. Therefore mineral processing of these disposals comprises the separation of liberated gangue by classification, beneficiation of locked valuables with density separation, liberation of valuables by grinding, and beneficiation of liberated valuables with flotation. The presented work shows the results concerning the composition of one exemplary heap and results of the classification as well as of the preconcentration tests achieved with material from this heap."

Jan 1, 2014

By Yuri Yemelianov, Stanislav Balikov, Alexander Epiforov, Andrey Boldyrev, Andrey Bogorodsky

"Test work was carried out using copper gold-bearing flotation concentrate with 6.85%Cu, 14.30%Fe, 20.70%S and 2.34%As. Gold and silver grade in the concentrate is 54.6 g/t and 92 g/t, respectively. Gold and copper are valuable components in the concentrate. Gold is partially associated with pyrite and fahlores. Copper in the concentrate can be found as tennantite (Cu12As4S13). The 71% of gold from the flotation concentrate is recoverable by cyanidation with simultaneous cyanide consumption in the amount of 96 kg/t. The major reason of refractoriness is that gold is fine encapsulated into sulfides and the presence of cyanicide-copper. The concentrate ground as much as 95% minus 10 µm was treated using low-temperature POX at the temperature of 100±5°C, L:S ratio of 5:1 and the process time of 1-5 hours. Residual sulfide sulfur in the cake is 2.28% which is 89% sulfide oxidation. The highest copper recovery to POX solution is 91%. It was found that gold recovery to cyanide solution is 85-94% during alkaline pre-treatment of POX cakes followed by cyanidation. In this case, cyanide and lime consumption is 75-90 kg/t and 120 kg/t, respectively. In order to recover precious metals from POX cakes leaching using sodium sulfite was carried out. Test work was conducted at varied reagent concentration, L:S ratio and leaching time. Gold and silver recovery achieved was 85-95% and 59-63%, respectively."

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By Jorge Rubio, Gabriel Berkowitz, Fabiano Capponim, Carlos Perez Guerrero, Elves Matiolo, Denise G. Nunes

This paper describes some advances in flotation research in fines (“F” 38 to 13 µm) and ultrafines (“UF” < 13 µm) mineral recovery by two different techniques, at laboratory scale. Extender flotation and flotation with .multi-bubbles. (bubbles with a wide size distribution) of copper sulphide fines (ore feed of about 1 % Cu) were compared with a .standardised. mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), .true. (bubbles-particles attachment only) flotation recoveries and process kinetics. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physico-chemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged.

Jan 1, 2003

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By L. W. Luo

Zeolite in some regions or countries of the world have been the subjects of materials for environmental remediation involving the use of removal to heavy metal ions and some organic pollutant as a sorbent because of its capacious ions exchange and huge surface area. This article addresses the equilibrium and kinetics for manganese adsorption using zeolite modified by hexadecyl trimethyl ammonium bromide (HTMAB) as a sorbent material over a range of pH between 3.4~7.2 with eight different Mn(?) solution concentrations. PHzpc (pH of zero point charge) of the sorbent was examined according to the method proposed by Tripathy and Kanungo, and a value of 6.91 was obtained. The experimental data fit langmuir?s model for the majority of pH and Mn(?) solution concentrations tested (0.92<R2<0.97). The maximal adsorption capacity, qm ascending with pH between 3.4~7.2, rise from 15.01mg?g-1 at 3.4 to 19.46 mg?g-1 at 7.2. Besides, the constant of Freundlich Kf have the same trend with qm, increases with pH ascending. And the sorption intensity, represented by parameter 1/n in Freundlich?s model, is favorable in entire range of metal ions concentration studied. Finally, kinetics data accurately fit to pseudo-second order which indicate that there must be sorption of Mn(?) behavior occurring on inner-sphere of the sorbent.

Jan 1, 2014

By A. Vidyadhar

Using pure quartz and hematite minerals, the adsorption mechanism of mixed cationic/anionic reagent schemes was investigated through Hallimond flotation studies. The flotation response of quartz and hematite independently with cationic and anionic collectors as well as with mixed cationic/anionic collector systems is assessed. The flotation response as a function of pH and collector concentration was investigated. The single mineral flotation tests in the presence of anionic collectors, quartz does not respond to flotation, but the C12 amine flotation of quartz was observed to be pH and concentration dependent. It was observed that hematite flotation recovery is maximum at acidic pH with sodium dodecyl sulphate (SDS), neutral pH with oleate, and at basic pH about 9.5 with C12 amine. Flotation results with both quartz and hematite indicate an increased adsorption of cationic collector in the presence of anionic collector apart from its own co-adsorption. The incorporation of oleate in between C12 amine molecules decreases the electrostatic head-head repulsion and thereby increasing the adsorption of C12 amine due to attractive tail-tail hydrophobic bonds, besides forming a closely packed adsorbed layer enhancing the hydrophobicity. The increase in oleate concentration beyond C12 amine concentration leads to the formation of soluble C12 amine-oleate complex / precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase. Keywords: quartz, hematite, adsorption, mixed collector system, flotation, zeta-potential

Sep 1, 2012

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003