Search Documents

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By Julian Wills

The Candrill was developed with Soredem as a one-operator rockdrill for Canadian narrow vein mining. It provides the benefits of increased drilling rates, lower noise and vibration, mass reduction of 20% and system cost saving. The Candrill is to be commercialised at the end of 2001 together with a stoper drill through Parts Headquarters, Novatek's Canadian agent. The Candrill or pneumatic drills may be further exploited using a simple mechanised drilling system to further reduce operator labour, improve drilling speeds by up to 50% and to enhance drilling accuracy. Novatek's drilling system for simple mechanisation in gold and platinum mines is integrated with roof supports, can operate in stope widths as low as 800 mm and has resulted in labour savings of 50%, improved advances per blast of 20 to 50% and improved operator safety and ergonomics.

Oct 1, 2001

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005

By A. J. Monhemius

"The paper reviews the history of modern iron control processes in hydrometallurgy. Particular attention is paid to the processes developed in the 1960s by the electrolytic zinc industry for the removal of iron from zinc sulphate leach liquors - namely the Jarosite, Goethite and Hematite processes. Problems faced by the industry in the safe disposal of the iron residues produced by these processes are discussed. The lessons learnt over the past half century by the zinc industry are projected on to the current efforts to develop hydrometallurgical processes for the treatment of copper sulphide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” is doomed to ultimate failure, unless and until methods are developed that can recover iron from solution in a form that can be directly utilised by the steel or pigment industries.INTRODUCTIONYou suddenly realise that age is catching up with you and that technology is moving on apace when you are asked to talk about the history of a process or a technology that you’ve grown up with. Such was my reaction when, out of the blue, I received an email last year from the chairman of the CIM’s Historical Metallurgy Committee, asking me if I would give a talk on the early developments of iron control in hydrometallurgy. Once I’d got over the initial shock of realising that I had now become living history, I was of course flattered that the invitation was to give a talk at the prestigious IMPC, a conference series that has been going for as long as I have been in the business. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, made the invitation even more appealing and appropriate, because I was the co-chairman of the First Symposium on Iron Control, together with my old friend, John Dutrizac (known by many as Dr Jarosite), which was held 30 years ago in Toronto.first became involved with iron at the very start of my career in hydrometallurgy – the research topic for my Masters degree thesis at UBC, back in the mid 1960s, was “Reductive leaching of Goethite with SO2”. My thesis supervisor was the late Professor Ian Warren, who himself was a protégé of Professor Frank Forward, one of the founding fathers of modern hydrometallurgy. Little did I realise at that time, now 50 years ago, that the problem of iron and how to deal with it in hydrometallurgical processes would be a theme that followed me throughout much of my 40-year career in academia."

Jan 1, 2016

By Louise H. Michaud

Albian Sands Energy is scheduled to begin production at its oilsands operations in the fall of 2002. Start-up includes the selection and implementation of over 75 IT systems or computer applications. These include engineering applications, systems required to control mining activities, maintenance, the processing plant and utilities, and also systems required to run the company, such as human resources, finances and inventory/warehousing. This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in Albian?s approach to identifying system requirements is the development of a Business Activity Model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been lead by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that don?t meet the company?s expectations. To ensure a more positive outcome, Albian believes that it is imperative that the company?s technical and business people are closely involved in the selection process. Integration of the IT systems is also key, including linking all applications through a Data Warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company.

May 1, 2002

By P. T. Craddock, H. V. Paliwal, L. K. Gurjar

The Indian cultural heritage of mining, smelting and the use of minerals and metals dates back to ancient times. Although the exact date of the commencement of such activities in India is not certain, Indians are known to have been familiar with gold, silver, copper, tin and lead and to a lesser extent with iron at least since the Vedic period (Table 1).

Jan 1, 1999

By Sanjeeva Latchireddi

"Deteriorating ore grade and high demand of metals has tremendously influenced the unit capacity of SAG mills. Pebble circuits have been added to the existing SAG circuits to increase their unit capacity. To make the pebble circuits justifiable, the grate openings are increased almost to 4.5 inches to draw large quantity of pebbles. The inherent transportation problems associated with SAG mills in closed circuit with pebble fraction are more complicated than the single stage SAG mill operation, because the coarse pebbles behave significantly different to that of slurry in pulp lifters. In addition, operation of mills at higher speed, to take advantage of precise design of high release angled shell lifters significantly reduces the discharge efficiency of the conventional pulp dischargers. The presence of a sizable quantity of pebbles in the pulp lifter limits the space available and reduces the flow gradient through the grate thus increases the load inside the mill and hence the mill power-draw. This paper analyses all the problems associated in discharge of slurry and pebbles in SAG mills with pebble circuits. The Outokumpu patented Turbo Pulp Lifter (TPLTM) aims at eliminating the inherent material transport problems to ensure good grinding conditions. Recent installation of TPLTM in a 26-ft SAG mill has proven these claims by reducing the specific power consumption while increasing the mill capacity.INTRODUCTIONThe conventional wisdom is to look at the semi-autogenous grinding (SAG) mill as just another grinding mill in which ball charge, mill filling, and mill speed are varied to attain maximum throughput. Liner design for the SAG was also approached more from a wear perspective rather than a metallurgical and hydraulic-flow perspective. The extensive research work carried out by Latchireddi and Morrell (1997,2003a and 2003b) has demonstrated to think of the SAG as more of a pump in which the grates and pulp discharger end (“impeller”) were designed to efficiently discharge the product sized particles smaller than the grate size with minimal recirculation out of the mill.The rock load in the mill is essentially depends on ore characteristics and the discharge rate of broken particles. The discharge rate of the product material depends on how efficiently the discharge pump (grate and pulp lifters) is operating. Similar to the impeller design affecting the pump capacity, the pulp lifter design affects the discharge capacity (or mill throughput) of the SAG/AG grinding mills. The general arrangement of AG/SAG mills discharge system is shown in Figure 1."

Jan 1, 2007

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By Brian Hart, Roger St. C. Smart, James Francis, Mark Biesinger

"There are a number of challenges involved with the surface analyses of different mineral phases from process streams in a flotation facility. The first of course is to collect samples that are representative of the process and to ensure that they remain in a pristine condition prior to introduction into the instrument. In mineral processing, sample collection from the different streams is done on site and preservation involves simply removing oxygen from the sample by bubbling nitrogen or argon gas through the sample and snap freezing with dry ice.The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles confident mineral selection can be difficult with many multi-metal minerals (e.g. chalcopyrite, pyrite, sphalerite) and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers.In this paper we show that principal components analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. We will demonstrate, with specific examples, that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation.Species recognition based on the PCA method in a study of Cu transfer between chalcopyrite, pyrite and sphalerite mineral mixture clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases. A similar ToF-SIMS/PCA based study applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between the chalcocite and heazlewoodite minerals. The statistical analysis has been able to confirm some mechanisms and deny others proposed to control recovery and selectivity giving more focus on the control factors.The ToF-SIMS PCA statistical analysis has elucidated differences in surface chemistries which illustrate the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. In the flotation test concentrates, HIC conditioning resulted in the removal of these gangue fines thereby improving surface collector attachment efficiency, promoting a greater recovery of sphalerite."

Jan 1, 2007

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By G. Zhu

The straight Y-shaped silica nanorods have been synthesized on Si wafer by thermal chemical evaporation of mixed powders of silica and graphite at 1300_ and condensation on Si substrate without assistance of any catalyst. The synthesized samples were characterized by means of scanning electron microscopy, transmission electron microscopy. The results suggested that the straight Y-shaped silica nanorods have uniform diameter about 50-200nm and neat smooth surface. The growth of such silica nanorods may be a result of the fluctuation of external conditions and internal structure faults causing a change in the growth direction of silica nanorods developed.

May 1, 2008