Search Documents

By T. R. Heflin

The paper provides a comprehensive discussion of pump selection for the hydrometallurgical industry. Material suitability, in addition to proper size and design, will provide extended life for pumps in erosion /corrosion service.

Jan 1, 1979

By M. U. Savich

In Canadian mines, ear muffs are now an essential part of safety equipment. Because of this, a research study was conducted to investigate their efficiency. The main characteristics of eleven commercially available ear muffs were investigated in the laboratory and analyzed by: (I) a psychophysical method; and (2) a physical method. These investigations showed the following effects: head size has a significant influence on the attenuation because of a different clamping force; the amount of hair trapped between the ear muff cushion and the head decreased ear muff attenuation; attenuation and comfort are not in a causal relationship; with the use of glasses and their adapters, attenuation decreases-the adapters are not effective sound barriers; there are no great differences in attenuation with neck movement; the efficiencies of various brands of ear muffs are not equal; ear muffs with a small cushion area start serving their purpose more quickly because the force per unit area is larger; a clamping force larger than 900 g wt, in most ear muffs, does not cause an increase in attenuation; attenuation characteristics (ANSI 224.22 - 1957) of ear muffs show some correlation with physical tests. Nine ear muffs out of the eleven were tested under uniform conditions in mines. Three ear muffs were found to be the best. All three ear muff s have bands passing behind the head. The ear muff with a support strap, which improves comfort and maintains a good fit during wear, showed the best attenuation. Causes of poor attenuation are numerous: bad mounting of ear muffs on helmets, improper fitting, interferency by hair and glasses, improper wearing by miners, unsatisfactory enforcement by supervisory personnel, incomplete training of miners, etc. Results of this research have indicated that none of the ear muff s tested in this study contain all of the characteristics desirable in an ideal unit. Because of unsatisfactory ear muff attenuation in working conditions (/5 dBA), it should be a mandatory requirement that workers wear both ear muff s and ear plugs if the noise level is higher than 105 dBA (various literature recommends t io dBA). The key to the solution lies in the following: the foreman must be capable of helping and controlling miners in their task of wearing ear muffs properly; the program must be introduced to miners; and constant contact must be maintained with manufacturers.

Jan 1, 1979

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By David L. Anderson

"The objective of this paper is to describe the potential impact of inter-provincial competition f or new output capacity on the Canadian potash industry. It will be shown that the ramifications of such actions are potentially severe, especially since the potash industry is one of the few non-fuel minerals in which Canada purportedly possesses a significant degree of market power. More specifically, the paper addresses the impact of possible expansions in New Brunswick, Manitoba and, perhaps, Saskatchewan. The findings suggest that such initiatives could result in substantial excess capacity and the dissipation of monopoly rents. In summary, given the market structure of the industry, it is unlikely that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation.IntroductionThe objective of this paper is to discuss the potential impact of inter-provincial competition for new output capacity on the Canadian potash industry. The ramifications of such competition are potentially severe: given that the potash industry is one of the few non-fuel minerals in which we purportedly possess a significant degree of market power(1), it is important that sound supply management practices are followed. However, possible initiatives by New Brunswick, Manitoba and, perhaps, Saskatchewan may initiate an inter-provincial competition which could result in substantial excess capacity and the dissipation of economic rents(2). Given the market structure of the industry, it is not intuitively obvious that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation."

Jan 1, 1985

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984

By Y. Guglielmi, C. Gout, P. Henry, P. Dick, C. Nussbaum

For a decade, observations and experiments conducted in underground environments worldwide (mines, underground research laboratories - URL) made it possible to bridge the scale gap between laboratory scale and large scale faults. Indeed, underground rock laboratories allow developing decameter scale relatively well constrained experiments at the smallest distance from the hypocenters. URL’s experiments allowed developing new monitoring technologies coupling pressure-strain-seismic measurements and reproducing complete earthquakes sequences analogous to natural ones. They also allowed exploring past movements of faults and sometimes also paleofluids in three dimensions and characterizing different fault architectures and hydromechanical properties in unaltered conditions. This is particularly important in the study of faults affecting clay formations which could not be observed at the Earth’s surface because of the high alteration. Here we show how examples from the Mont Terri (Switzerland) and Tournemire (France) The URLs may help in (i) defining the concepts of fault architecture in shales, (ii) estimating fault hydromechanical properties from field decameter scale experiments. Some key results are that faults which are critically stressed or at the rupture limit can reactivate for stresses variations within the range of those produced by shallow underground excavations, and that slight micrometer-to-millimeter scale reactivations may lead to large factor-of-10-to-1000 permeability increases. Such promising results show that URL’s experiments may bring new insights on some key processes that control the relations between fault stability and permeability evolutions in very permeable layers.

Jan 1, 2015

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By S. Ianos, C. Vibert

Type and shape of large dams founded on rock depend upon the expected deformation of their foundation. Their design consequently requires the assessment of the deformability of the rock mass at large scale. Seismic refraction, laboratory tests on rock samples and empirical formulas can provide an order of magnitude of the deformation modulus, with a limited degree of reliability. Direct in-situ measurement of the deformability of a volume of rock is therefore preferred, which integrate the effect of discontinuities, such as plate loading tests, dilatometric tests, etc. The authors have been compiling results obtained by in-situ deformability tests on a number of dam sites, including the Scarabée (“Petite Sismique”) method. This last method consists in thoroughly analysing the shape of seismic wave forms transmitted through the rock mass. It has been used since now more than 40 years over a large number of dam foundations, and has proved to provide a satisfactory assessment of the static deformation modulus. After comparing the results obtained from different methods on six dam sites, the Authors conclude that their reliability closely depends upon the size of the loading device in relation to the spacing of the discontinuities. Attempts to correlate results from different types of in-situ loading tests reveal difficult, because closely depending upon local geotechnical conditions at test location. Plate jacking tests appear to be the most reliable, because involving a relatively large volume of rock. On the other hand, the Scarabée method (“Petite Sismique”) allows a rapid assessment of the deformation characteristics of the rock mass at large scale, and has been found to provide values generally in agreement with those from plate loading tests, while dilatometric or flat-jack tests were found too dependent upon local conditions. The Authors conclude that preference should be given first to the Scarabée method, which uses light equipment and is quickly performed, together with an accurate geological and geotechnical assessment for interpretation. In a second stage, Scarabée shall be complemented by adequately performed plate jacking tests in selected locations, in order to cross-check results and refine the assessment. The general accordance between the results of the two methods, which both can integrate anisotropy of rock masses, justifies this statement.

Jan 1, 2015

By P. R. Goad

"Kidd Creek is a large volcanogenic base metal sulphide deposit, located near the west end of the Abitibi greenstone belt, 27 km north of Timmins, Ontario. The rhyolite geology is characterized by a NNE-striking and steeply east-dipping package of rhyolite volcaniclastics upon which has been imposed a strong ESE-striking and north-dipping structural fabric . Massive rhyolite units with grey-black. chloritic cores and yellow, sericitic margins intrude as dykes into the stratigraphic footwall and as sills higher in the stratigraphy. Massive rhyolite units positioned near the top of the felsic pile exhibit an extensive marginal development of hydraulic fracturing and are termed crackle-brecciated rhyolite.The stringer sulphide zone is positioned in a lobate blanket of crackle-brecciated rhyolite at the top of the felsic pile. The stringer sulphide zone is characterized by a mature chemical alteration, being specifically depleted in alkalis and enriched in iron-rich chlorite. with accompanying silica, sericite and carbonate alteration. A suite of trace elements characterizes this mature alteration. The massive rhyolite units, which intrude lower in the rhyolite volcaniclastics, exhibit a core of weak chlorite alteration and strong marginal sericite alteration. Tight or unfractured massive rhyolite units are essentially devoid of sulphide mineralization and exhibit a suite of trace elements characteristic of this immature alteration. It is interpreted that the massive rhyolite units intruded into an already evolving system and ""choked-off"" active conduits carrying hydrothermal fluids and subsequently acquired an immature alteration signature. Rhyolite units positioned higher in the pile developed intense hydraulic fracturing and a mature alteration coincident with the formation of the stringer sulphide zone. In summary, a model, based strictly upon the rhyolite geology, is reviewed to assist in the exploration for volcanogenic base metal sulphide deposits."

Jan 1, 1985

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By Michael Davies

Mined Material Management Meeting or Missing the Mark? o you agree that we have the technology to consistently design robust M3 facilities? ?YES your experience do these M3 facilities perform as expected during operations? ?USUALLY hat can be done to improve performance, e.g. better communications between project and operating teams, discontinuity between design and operational input by designers, others? ?UNDERSTANDINGWHY THINGS GO WRONG an we identify the key characteristics of ?good M3 facilities?, i.e. ones that are performing well? Can we identify ?good M3 facilities?, i.e. ones that perform well and can be held up as examples? ?WITHOUT QUESTION?? your opinion, for what reason do they not perform as expected? ?NO SINGLE REASON??..

May 1, 2010

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By Franz Simon

Conventional fine gold electrolytes for barrel applications working electrolytically actually permit significant precious metal savings by corresponding optimizations but the most gold is still deposited on areas of the components where it is not absolutely essential for the desired bonding and soldering applications, i.e. in high current density areas. Therefore an electrolyte working electrolessly has been developed which inevitably leads to a much more uniform thickness distribution since in an electroless process there are no areas favoured by metal deposition and current distribution. The new electrolyte will be presented and its performance will be compared with conventional electrolytes as regards thickness distribution. The potential gold savings will be discussed.

Oct 1, 2003

By George Dogbe

Open pit optimization forms the basis of mine design, production planning and construction of mine facilities. The negative effects of this phase may include substantial reductions in ore recoveries, relocation of waste dumps and surface infrastructure, extraction of unwanted waste, with a cumulative effect on mine value reductions. As a result, this area has received significant research focus using linear and dynamic programming, heuristic, genetic and stimulation algorithms and the graph theory. These algorithms are derived from rigorous mathematical models, but they are built on the assumption that all the periodic production capacities are extracted at the time of analysis. This assumption weakens the models because mining occurs over significant time period. In order to develop a comprehensive model that accounts for the timing of material extraction, the current models, which are built on the economic block value (EBV) concept, must be modified to account for time. In this paper, the authors develop a model of the optimization problem using the 2-D Lerchs-Grossmann?s optimization algorithm. This model is used to investigate the effect of periodic discounting on the optimal pit layout design by designing an integrated pit optimiser (IPO) that incorporates ?production scheduling?. IPO uses the ensuing discounted economic block value (DEBV) as a basis for the pit optimisation process. The time-dependent model is compared with a time-independent model. The results show that discounting has no effect on the optimal pit contour although the reported pit value is overstated if the EBVs are used instead of the DEBV. The authors, however, believe that this conclusion may not be general and could have been influenced by the nature of ore body geometry and the proposed mining strategy.

May 1, 2004