Search Documents

By Andrew Matyas

"During the summer of 1968, the author was employed in the Research Department of Dominion Foundries and Steel, Limited, Hamilton, Ontario. Over the years, Dofasco has been conducting a program for developing more efficient control of its basic oxygen steelmaking process. The author was thus able to obtain a variety of viewpoints from both research engineers and furnace operators. He also had access to extensive literature dealing with BOF control schemes underway at other major steel producers. This paper describes the present state of developments in BOF steelmaking control.The necessity for efficient BOF control is pointed out. To appreciate the variables to be controlled, a brief outline of process fundamentals is included. Technical aspects of present methods of practical control are examined in detail; the relative merits of dynamic over static control models are emphasized. Finally, it is shown how an effective dymic-optimizing control scheme serves as the basis for closed-loop computer control of the process."

Jan 1, 1970

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By V. Bazhko, V. Yahorava

The calcium sulphate waste stream of the wet phosphoric acid process, commonly called phosphogypsum (PG), contains the majority of rare earth elements (REE) initially present in the apatite feedstock. Mainly light and middle REE are present in PG and their total concentration ranges from 0.27% to 0.35% by mass. Worldwide, around 7 billion tonnes of PG have been produced to date at a current growth rate of 150-200 million tonnes per annum. In total, an estimated 21 million tonnes of REE are locked in PG waste dumps around the world. Due to the value of the REE contained in PG dumps a number of processes have been devised for their recovery. The majority of these processes applied complete or partial gypsum dissolution, but were deemed not viable due to high capital and operating costs. Mintek developed an alternative method for the recovery of REE from PG by applying Resin-in-Leach (RIL) technology. This technology was tested on PG sampled from dumps and current arisings from South African phosphoric acid production plants. The extensive testwork program included evaluation of various lixiviants and optimisation of lixiviant additions, optimisation of REE leach and adsorption conditions, batch equilibrium and kinetic adsorption tests, continuous RIL testwork and numerous variability tests. It was found that PG from different sources was highly variable, both in terms of REE recovery as well as physical properties of the material such as viscosity and filterability of the slurry. The recovery of REE varied from 15% to 80% depending on the origin of the samples. A high-level economic study indicated that at a price of >21 $/kg for mixed REE oxide product in conjunction with an overall REE recovery as low as 15% the economics of REE recovery from PG via RIL technology may already be favourable.

Jan 1, 2016

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By Gordon T. McKenna

"Syncrude Canada Ltd. is developing new concepts in lease-closure landscape design for its Oil Sands Leases 17 and 22 in northeastern Alberta. Closure planning is becoming an integral part of the planning cycles and of the lease operation. By incorporating closure planning into the day-to-day operation, the company will achieve acceptable lease closure in an economical manner. Ultimately, Syncrude will achieve lower operating costs through innovation in mine planning and a reduction in residual liabilities.New concepts being evaluated for lease-closure landscape design include: designing for closure, use of landforms and natural analogs, self-armouring bouldery ground, robustness in design, landform grading, terrain analysis of reclaimed land, geotechnical hazard assessments, choices in closure design timeframes, passive maintenance, determining post-closure monitoring goals, engineering tailings, engineering other substrates, use of test plots and field demonstrations, geomorphologic monitoring of reclaimed lands, defining closure goals, and visiting other mines. These concepts are being formalized under the new discipline of Landscape Engineering."

Jan 1, 1996

By E. C. W. Perryman

BEFORE describing the methods used for fabricating uranium into various shapes and sizes it is necessary to illustrate briefly the unusual conditions under which uranium has to operate when used as a fuel element in a reactor. During reactor operation, for every fission that occurs two atoms of intensely radioactive fission products are produced together with two or three neutrons. The neutrons that are ejected possess several m.e.v. of energy and when one of them strikes an atomic nucleus, that atom acquires up to 105 e.v. of kinetic energy. This is large enough to displace the atom from its lattice position and send it shooting through the crystal, displacing other atoms out of their lattice positions. The net result is that a large number of vacancies and interstitial atoms are formed within the crystal lattice which sometimes have profound effects on the physical and mechanical properties of the material in question.

Jan 1, 1957

By J. Budac, R. Kofluk, D. Belton, M. Sjogren

A series of tests were performed to determine the flammability limits of mixtures of oxygen, ammonia, steam and nitrogen, over a solution, in a sealed autoclave. The partial pressures of ammonia and oxygen in the vapour space were varied by adjusting the character of the solution and by adjusting the oxygen concentration in the oxidant gas respectively. The data shows that flammable conditions can be minimized by controlling the operating temperature, reducing the ammonia content in the solution, increasing the concentrations of Ni, Cu and Zn in solution and keeping the % oxygen in the gas phase less than 15.5. Observations were also made that suggest that the presence of an aerosol in the vapour space may hinder ignition.

Jan 1, 2004

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By R. Lasmanis

"Washington State&apos;s diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By Abu Syed H. Kabir, Mehdi Sanjari, Steve Yue, Jing Su, In-ho Jung

AZ31 magnesium alloy sheets were produced by high speed rolling (HSR) at 1000 m/min at a low temperature of 100 ?. A high reduction of 72% can be achieved in single pass. At the reduction of 30%, the microstructure was covered by shear bands and twins. When the reduction was increased to 49%, dynamic recrystallization (DRX) was clearly observed in the vicinity of shear bands and twins and the full recrystallization was seen at a reduction of 72%. In order to study the static recrystallization (SRX) behavior on the heavily twinned structure, annealing was then carried out at 200 ? on the as-rolled specimens at the reduction of 30% for different times. Static recrystallized grains were also firstly observed on shear bands and twins after 45 s and the microstructure was mostly fully recrystallized after 1 h annealing with a few retained large elongated un-recrystallized grains. Texture weakening was found during annealing on the heavily twinned specimens by SRX, but not during high speed rolling by DRX. In the present study, effect of DRX and SRX on microstructure and texture evolutions during rolling and annealing were compared.

Jan 1, 2015

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By W. A. Jones

Purpose of Paper Geophysics is a highly developed science which has found a wide use in industry. Perhaps the most spectacular application has been in the field of oil exploration. It has been estimated that, up to the end of 1939, geophysics was responsible for the discovery of five billion barrels of oil. In 1944, the sum o $40,000,000 was expended for geophysical work in the search for new oil deposits. Although the metal mining industry has so far made comparatively little use of the science, it is becoming increasingly common for the exploration engineer or geologist to be required to co-operate with the geophysicist. Many papers dealing with applied geophysics have been published but in most of them advanced training in physics and mathematics on the part of the reader has been assumed. It is difficult for the average engineer to obtain a ready understanding of the equipment, field procedure, and scope and limitations of the science from the literature. The present paper attempts to describe briefly and in simple terms the principles underlying magnetic, self-potential, and electrical resistivity methods and their application to a field problem. Introduction Geophysics is concerned with the study of gravity, magnetism, natural earth currents, earthquakes, vulcanism, and many other natural phenomena. The methods, originally devised for the measurement, for scientific purposes, of the forces associated with such phenomena have been adapted to the search for buried deposits of economic value. If the body sought has large dimensions and distinctive physical properties, geophysical measurements may reveal associated, and in some cases quite characteristic, anomalous features. However, in many instances the mass cannot be indicated directly but has a common association with geological features which can be defined by physical measurements. Although such surveys cannot specifically identify oil, metalliferous minerals, or other commercially valuable substances, it is possible to delineate anomalous sub-surface physical features which, with the help of geological information, can be assessed as possible or probable indications of the body or structure sought. The nature and extent of the material causing an anomaly, and its economic importance, can only be determined by further exploration, such as drilling.

Jan 1, 1947

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012