Search Documents

By S N CARRAS

Ore reserve estimation is a procedure involving data collection, data storage and judgement and assumptions about geology mining and metallurgy. Calculations are based on these assumptions and an economic analysis on projected cash flows is carried out. Ore reserve estimation must therefore be subjective and will always depend on the extent to which the assumptions used in arriving at the estimate are correct. This paper is an attempt to summarise the many aspects that can contribute to ore reserve problems and to offer some suggestions on how to minimise these problems. For further details on specific concepts readers are referred to the detailed descriptions in the referenced papers.

Jan 1, 1992

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives.Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring?It is these questions which I wish to discuss in this address.There is nothing new about change in the mineral industry, it has been happening for thousands of years and it will continue as long as civilisation exists on earth. One type of change is economic and we are all aware of the rises and falls which occur in the prices of metals and minerals (Figure 1). When these have happened in an orderly manner, and could be predicted and planned for, it has been possible to take advantage of the benefits and minimise ill-effects, but when they were sudden and precipitate, and could not be predicted, the consequences were serious. The extreme example, of course, was the oil price shock of the 1970s which had such disastrous effects on industry and society.Other types of change are social, cultural and political. They have all been important in recent years and will continue to be so in the future.But it is technological change which may well be the most important because its effects are profound and irreversible, and alter irrevocably the way in which we live. So in discussing the mineral industry in a changing world I will talk specifically about technological change.

Jan 1, 1989

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By D Guibal, J Vann, M Harley

Many sample value distributions are highly skewed and present variograms with high relative nugget effects and/or short-range structures. In consequence, significant deskewing of the histogram and variance reduction occurs when transforming between sample and block support, where blocks are of significantly larger volume than samples. When making estimates in the mining industry we usually wish to estimate on the basis of block support rather than sample support. The selective mining unit (SMU) refers to the minimum support upon which ore/waste allocation decisions can realistically and practically be made. The SMU is usually significantly smaller than the sampling grid dimensions, in particular at exploration/feasibility stages. In a non-linear estimate, for each large block (by convention called a æpanelÆ) we estimate the proportion of SMU-sized parcels above a cut-off grade threshold. A series of proportions above cut-off defines the SMU distribution. Use of such non-linear estimates reduces distortion of grade-tonnage curves and provides a better basis for mine planning and economic decision-making. At present, Multiple Indicator Kriging (MIK) is the most widely used technique for performing estimation of recoverable resources. MIK is not the only approach available and it has some potentially serious limitations. The MIK technique is described and a number of theoretical and practical implementation issues are examined. In particular: MIKÆs assumptions about spatial distribution of grade; the behaviour of indicator variograms; application of change of support models; order relationship problems; and modelling the tail of the distribution. Some simple tests are described which allow us to determine the suitability of different estimators for a given deposit and criteria to identify a preferred estimator are also examined. Uniform Conditioning (UC), an alternative estimator which may be used instead of MIK, is described.

Jan 1, 2000

The organisers of this function have suggested that this presentation should accomplish the following broad goals:set the technical tone for the conference to follow, implying some discussion of the æstate-of-the-artÆ of reserve estimation; and raise some current and common problems or deficiencies in our art in order to be thought provoking. As an engineer it is always easier to raise problems than to solve them with state-of-the-art. Consequently, I have had to limit the extensive list of problems that could have been discussed within this presentation. In regard to the state-of-the-art, this presentation will not be an esoteric discussion of the latest statistical estimation processes, although I intend to challenge those with skills in that area to address some of the thought provoking issues later on. The subtitle of the paper was established after reading an excerpt from æLife on the MississippiÆ by the American humorist Mark Twain in which Twain observed that the Mississippi River had become shorter during his working period on the River due to natural cut-offs and man made channels. Projecting into the future, he calculated that by now, Cairo, Missouri and New Orleans, Louisiana would become a single city with one mayor (the two cities are still separated by some 500 air miles). As a moral to this story Mark Twain observed that one can obtain: æwholesale returns of conjecture out of such a trifling investment of factÆ.

Jan 1, 2000

By S Thomas, E Grimsey

Mining education in Australia has undergone another cyclical downturn over the past five years and several departments have been discontinued while others are still teetering on the brink of destruction. During this downturn Curtin UniversityÆs WA School of Mines (WASM) has managed to stay alive and well, but this has not been by accident. This paper outlines some of the strategies and experiences that have kept WASM in a strong position and offers hope to other departments and schools elsewhere that are still experiencing difficulty. This paper is also directed at all mining departments and schools that are certainly going to see it all happen again after the next mining boom turns to bust.

Jan 1, 2004

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By P Rubie, J Russell

This paper looks at the past, present and not too distant future of grinding mill relining.Since the adoption of autogenous grinding (AG) mills and semi-autogenous grinding (SAG) mills as the primary ore reducing devices in the comminution circuit, plant shutdown frequency and duration has largely been driven by the liner maintenance requirements of these mills.The past 30 years have seen the introduction of many technologies to reduce relining times and frequencies. Advanced relining systems have been developed which include single and twin Mill Relining Machines, capable of placing large (up to 8000 kg) liners, high energy recoilless THUNDERBOLT Hammers, and high capacity Feed Chute Transporters. Despite these advances, today many of the hazards associated with mill relining remain and reline times still vary considerably between mine sites. A sophisticated discrete event simulation program, designed to analyse the mill relining process, has revealed the dominant influences on reline times of crew performance and of the need for safe access to larger segments of the mill.A new generation of advanced and semi-automated technologies is currently being tested that will address these remaining challenges. These technologies remove people from the hazardous environment inside the mill and will allow techniques used in modern advanced manufacturing to provide a near-future step change in mill relining safety and performance.CITATION:Rubie, P and Russell, J, 2018. 21st century relining – the path to greater mine site profitability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 621–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Burgess, G Scanlan

In 1993 after over 110 years of mining operations, production ceased at the Broken Hill North Mine. Following the cessation of operations a rehabilitation program was developed to satisfy the requirements of the various government departments. This program has been implemented progressively since mine closure. The paper will discuss: primary aims and objectives of the rehabilitation program, implementation of the program, rationale behind rehabilitation objectives, and problems encountered in implementation of the program. To-date the primary rehabilitation of the mine has involved the capping of redundant tailing dams with inert waste rock to prevent the contamination of the receiving environment. A Water Management Plan has been developed to contain all run-off from the mine area in an extreme storm event. A cultural heritage assessment of the leases has been undertaken to ensure the rehabilitation is consistent with the historical significance of the site and community expectations. All redundant material from the mine has been sold in a æno reserveÆ auction and the workshop area has been relocated to the Southern operations. At present the only active areas on the mine are a maintenance area for equipment for the Potosi open pit, and a primary crusher for Potosi ore which is railed to the Southern operations for further processing. Upon completion of the rehabilitation program, Pasminco Broken Hill Mine intends to relinquish the mining leases to the Department of Mineral Resources.

Jan 1, 1998

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

By T Higuchi, K Fukada, K Takehara, Y Iwami, S Fujiwara

Following the Paris Agreement adopted in 2015 and the SDGs, reduction of CO2 emissions has been taken up as an issue worldwide, and the steel industry, which has a particularly large emission, is required to significantly reduce it. Most of the CO2 generated in the steel industry is generated from the ironmaking process, due to the use of coke and its raw material coal in the ironmaking process. JFE Steel Corporation has been considering the use of hydrocarbon-based gaseous fuels and liquid fuels as a partial alternative to coke breeze used in the sintering process since 2006, immediately after the Kyoto Protocol came into effect in 2005. In a laboratory study, a pot test was used to investigate the effect of the type of fuel, its amount and its injection method on the heat pattern in sinter bed. As a result, the authors developed a technology, in which a predetermined amount of gas fuel or liquid fuel was injected from the surface of sintering bed to extend the holding time of 1200°C or higher at which liquid phase sintering occurs in the layer, to improve the sinter strength while reducing the amount of coke breeze. The authors succeeded in putting this technology to practical use using hydrocarbon-based gas fuel in 2009 and achieved a maximum annual reduction of 60 000 tons of CO2 per sintering machine. In this report, the authors introduce the results of laboratory studies on the use of various energy sources, the practical application of the technology for injecting hydrocarbon-based gaseous fuel into the sintering machine, and the operational results.

Nov 8, 2021

The Australian minerals sector has a shortage of skilled professionals to satisfy an industry that is experiencing renewed vitality. Graduate numbers are low throughout Australia and the world, while economic rationalisation is seeing many educational institutions downsize, or even close, their minerals-related programs. In addition to requiring more entry-level graduates, minerals producers are looking to update the skills of their current workforce to keep up with the industryÆs continuing technological revolution. To address the issue the Minerals Council of Australia (MCA) endorsed collaboration between several Australian minerals producers and a team of universities to generate the Mineral Tertiary Education Council, or MTEC. MTEC recently initiated a venture to increase the availability of professionals with relevant skills to the minerals industry. Primarily aimed at delivering postgraduate programs, the initiative will allow graduates from other disciplines to æconvertÆ to the minerals sector as well as provide professional development training to an existing work force. This venture represents a novel approach in that courses will be delivered by more than one institution and will employ innovative teaching materials with flexible and remote delivery formats. The programs will cater specially for professional development in the minerals sector, which generally requires high flexibility due to the nature of work conditions and locations.

Jan 1, 2004

By A Chandra, P Guj

Only a few complex real options can be valued using closed-form equations, such as the Black and Scholes formula, because these algorithms are restrictive and prevent the construction of practical project evaluation models. Although a binomial lattice method paired with the ærisk-neutral probabilityÆ provides an easier and flexible modelling of exploration and mining projects, it has limitations when projects are complex, long-lived and influenced by the interplay of various market and private uncertainties. In order to overcome these limitations, modern decision tree software using dynamic programming capability can be used for real option valuations. This is a powerful computational tool in which the impact of various sources of uncertainties can be differentiated, so that the optimal decision path can be explicitly displayed visually. There has been significant academic controversy surrounding whether different real option (RO) valuation methods would lead to different real option values (ROV). This paper, using a realistic copper mining example, demonstrates that as long as the same degree of subjectivity and consistency are used in different real option valuation methods, they yield the same result. This conclusion is valid irrespective of whether the cash flow volatility generated by various sources of uncertainties is handled in an aggregated or in an explicit and differentiated manner. This paper compares two choices for an investor either to æbuy now and developÆ a project or to enter into a ætwo-year option to purchaseÆ after the proponents have developed it. It also shows how significantly different net after-tax operating cash flows may be generated by these different choices on the same underlying asset represented by the project. This is due to the difference in the amount and timing of the relevant capital investments affecting the depreciation and amortisation charges and as a consequence, the income tax paid. CITATION:Guj, P and Chandra, A, 2012. Real option valuation of mineral exploration/mining projects using decision trees - Differentiating market risk from private risk, in Proceedings Project Evaluation 2012 , pp 177-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

About 90 per cent of the pre-mining BIF-hosted iron ore resource of the Hamersley Province of Western Australia is of the Phanerozoic supergene martite-goethite type. The remaining ten per cent formed as supergene deposits at ~2000 ¦ 200 Ma, and were later modified by burial to form the Proterozoic martite-microplaty hematite ores. The supergene-metamorphic segment of this general unified model has been challenged by three recently published hypogene-based genetic models for the hematite ores, all requiring meteoric oxidation to produce the ore. The most recent and detailed, by Taylor et al (2001), is based on data from the small Southern Batter and North deposits of the Mount Tom Price mine. The authors proposed that during Stage 1 æoverpressured bicarbonate-saturated basin brines from the dolomite aquifer of the Wittenoom FormationÆ at 150 - 250¦C, dissolved free silica from BIF to produce a stratigraphically thinned, magnetite-carbonate-silicate-apatite rock. In Stage 2, meteoric oxidation of siderite to secondary microplaty hematite + ankerite, and magnetite to martite, at unspecified elevated temperatures and pressures, was followed by carbonate leaching (Stage 3). Finally, during Stage 4, weathering with removal of apatite, produced the typical low-phosphorus, porous martite-microplaty hematite ores of the Tom Price-Whaleback type. However, evidence of both microplaty hematite and martite reduced to magnetite, and of infill silica, apatite, and ferroan chlorite, with late-stage pyrite, in the pore space of martite-microplaty hematite ore, shows that the hydrothermal activity at Mount Tom Price is a post-ore event. Neither pyrite nor ferroan chlorite could resist the oxidation required to form hematite ore. Recrystallisation of microplaty hematite in these infilled zones to a typically coarser form than present in most of the normal ores, is a further supporting factor. A more credible, post-ore alternative to the hypogene genetic model is suggested here. Re-exposure to leaching by ground water of the metamorphosed ore deposits in the Phanerozoic resulted in the partial removal of remnant goethite. Localised modifications in the porous BIF/ore contact zones were driven by exothermic oxygen/pyrite/carbon reactions in the footwall Mt McRae Shale. Cool descending oxygenated meteoric water in the permeable ore horizons, acted as one limb of a thermal convective cell. In the other limb, heated reducing solutions rose through the permeable contact zones, to produce the observed localised modifications of BIF and ore. Expelled silica from the carbonatised BIF invaded adjacent porous ore to form erratic silicified ore zones, and to produce the local quartz vein systems found in the associated overlying BIF.

Jan 1, 2002