Search Documents

By J Lombardi

OZ Minerals' Prominent Hill copper-gold concentrator is located 130 kilometres south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for eighteen cells.Generic proportional – integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Aug 8, 2011

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By F Tang, Ö K. Büyükuslu, M Baben, S Petersen

GTT-Technologies’ ChemApp for Python was developed to provide a powerful, easy to use interface to ChemApp for a programming language highly popular with scientists and engineers. It is used, for instance, by GTT to develop program modules such as the CALPHAD Optimiser for the FactSage™ software, by customers to move from interactive FactSage calculations to perform versatile scripting with Python, and by GTT and its partners in research projects in the area of materials informatics. Computational thermochemistry is fundamental for advancing sustainable metallurgy and creating new alloy compositions for engineering applications. Materials informatics involves handling vast amounts of data and complex workflows. GTT’s approach uses ChemApp for Python and the FactSage thermodynamic databases to design recyclable alloys from the start, incorporating a higher percentage of scraps while aiming to simplify the workflows to simulate material design steps. Challenges arise due to recycling scraps, introducing more elements for consideration. CALPHAD-based databases accurately cover materials from primary metallurgy, but additional data for minority and critical elements is crucial for precise computational modelling. GTT combines machine learning-based ab-initio databases with traditional CALPHAD databases to cover the complete chemical space with appropriate accuracy. The design of a hardfacing alloy through a high-throughput materials informatics approach is used as a demonstrator of the current possibilities.

Jun 19, 2024

By C Zschiesche, alam, A Abadias Llamas, A K

Lead has the ability to collect and carry valuable metals such as copper, bismuth, antimony, tin and precious metals for their downstream recovery. Therefore, lead metallurgy is key for the raw material supply that our society demands. Lead smelters, excluding lead-acid battery recyclers, tend to process more complex primary and secondary raw materials, which are mostly processed via the pyrometallurgy route. Accordingly, understanding the slag system of these metallurgical processes is key for the efficient industrial operation and recovery of minor elements. Glencore Nordenham is an integrated lead and zinc smelter in northern Germany with a production of 92 000 t of lead and 164 700 t of zinc in 2022. The lead production line processes complex leadbearing raw materials through the direct smelting process. Firstly, the feed mix is smelted in a Top Submerged Lance (TSL – Ausmelt®) furnace, where a lead bullion containing minor metals and a lead-rich slag are produced. Then, the lead-rich slag from the TSL is tapped (via launder) into a Side- Blown Furnace (SBF), where lead oxide is reduced to produce lead bullion (with minor elements) and discard slag. The lead bullion from both stages is refined to produce lead (>99.9 per cent) and recover the minor elements (Cu, Ag, Au, Sb, Te, Bi etc). This paper reflects the experience of operating the SBF after the first five years of operation and describes its ‘PbO-SiO2-FeOx-CaO-ZnO’ slag system. Firstly, the slag system, the furnace operating region and the potential solid phases present are discussed from a theoretical point of view. This theoretical study has been performed using FactSage™ 8.2 and the database developed by the Pyrosearch group at the University of Queensland, Australia (UQPY). Then, the FactSage™ simulations are compared with industrial slag measurements. Finally, some examples on how the slag knowledge gained at Glencore Nordenham can help the industrial operation of the SBF are discussed.

Jun 17, 2024

Production scheduling of open pit mining is a key area as it deals with the management of operating cash flows of mining companies. The efficiency of long-term schedules is usually assessed with economic criteria such as net present value (NPV), discounted cash flow rate of return (DCFROR) and payback period, which are not sufficient on their own for revealing the complex picture of the decision-making process.This paper offers a thorough analysis of the most important contemporary criteria of long-term production scheduling, as way to provide the mining practice with a new approach to the decision-making process. The list of criteria includes technological, economic and probabilistic ones. A detailed case study is provided aiming to illustrate the applicability of the criteria for comparing the scheduling approaches regarding the economic interests of a mineÆs owner and contractor. The results obtained can be used for revealing new trends in the current methodology of open-pit production scheduling optimisations.

Sep 26, 2011

By G V. R Goodman, G J. Chekan, J M. Listak

The extraction and transport of coal from underground coal mines can result in significant liberation of coal and/or silica dust into the mine atmosphere. Mine operators have long used ventilating air as a primary means of diluting generated dust, removing dust from the working faces and preventing dust from reaching the minersÆ working environment. As production levels have increased, mine operators continue to be challenged in maintaining dust concentrations below compliance levels. The need for maximising the effectiveness of available ventilating air in conjunction with other effective controls, such as water sprays and dust collectors, continues to be critical to the long-term health of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale laboratory and mine-site research to evaluate improved application of dust controls for both longwall and continuous mining methods. A summary of recent research results and recommended practices will be provided.

Jan 1, 2005

By J Demchak, L M. McDonald

The duration of acid mine drainage flowing out of underground mines is important in the design of watershed restoration and abandoned mine land reclamation projects. People conducting land reclamation projects usually employ remediation strategies once (reshaping land, revegetating soils, and installing water treatment) with the hope that these methods will adequately improve water quality for a long time, with little planning for future changes. An understanding of changing acid water conditions from underground mines over time will help in designing efficient and cost-effective treatment methods. Past studies have reported that acid water flows from underground mines for hundreds of years with little change, while others state that poor drainage quality may last only 20 to 40 years. Several factors are important in making a prediction of drainage quality over time, such as inundation or flooding history, coal seam characteristics (primarily sulfur content), residence time of water in the mine, time since mine closure, mining method and amount of coal remaining, collapse of roof and other disturbances within the mine, and subsequent nearby surface mining. More than 150 above-drainage (those not flooded after abandonment) underground mine discharges were located and sampled during 1968 in northern West Virginia, and we revisited 44 of those sites in 2000 and measured water flow, pH, acidity, alkalinity, Fe, Al, and sulfate. All 44 discharges were from mines in the Pittsburgh and Upper Freeport coal seams, and both seams have been extensively mined in this area during the past 70 years. We sampled during the same months (June to October) as were sampled in 1968, and we found no significant difference in flows between 1968 and 2000. Therefore, we felt that the water quality data could be compared and that the data represented real changes in pollutant concentrations. There were significant water quality differences between year and coal seam, but no differences between disturbed and undisturbed mines. Average acidity declined 79 per cent between 1968 and 2000 in Pittsburgh mines (from 3342 to 702 mg/L), and 56 per cent in Upper Freeport mines (from 1189 to 519 mg/L). Iron decreased an average of about 80 per cent across all sites (from an average of 345 to 69 mg/L), while sulfate decreased between 50 to 75 per cent. Pittsburgh seam discharge water was much worse in 1968 than Upper Freeport seam water. Twenty of our 44 sites had water quality information during 1980, which served as a midpoint to assess the slope of the decline in acidity and metal concentrations. Almost all parameters showed an exponential rate of decline in acidity, iron, and sulfate.

Jan 1, 2003

Geophysics is playing an increasingly important role in the exploration industry. In the soft rock scene the application of seismic techniques is basically mandatory prior to any drilling program. Simply, this is because, in a majority of situations, the seismic method is ideally suited to mapping accurately relatively flat lying strata and displaying structures that may host oil or gas. It is worth stressing that seismic methods do not delineate oil or gas but they map well in two or three dimensions. In the base metal arena, geophysical methods used are generally focussed on direct detection methods with the mapping application not often used except in potential fields (magnetics and gravity). The success rate in the last decade has not been good but this does not only apply to the application of geophysics; it really applies across the board of exploration techniques. Both geological and geochemical exploration have not had a success rate commensurate with the funds injected. Basically in the last ten years we have failed as explorers! As explorers we have been negligent in mapping. As geoscientists we have let the basic mapping and observation skills diminish û the old adage æboots on the groundÆ is still applicable but are we doing enough of it? The answer is clearly no. As explorers the huge burden of bureaucracy, eg Government Acts û local, state and federal, safety compliance, environmental compliance, etc has reduced the ægeologicalÆ time dramatically. This has culminated in an over-reliance on quick fix solutions, eg spot the bump geophysics or geochemistry. This obviously simplistic scenario is arguable but there is no doubt in the geoscientific areas we have failed in the last decade to provide adequate geoscientific maps to assist in exploration. This failure could partially be responsible for the current demise of the industry resulting in a reduction in exploration dollars and, hence, people. This trend is seen acutely in the geophysical area where the head count in comparison with the geological fraternity is low. Other trends during this downturn are inevitable as explorers maximise the use of the dollar in exploration and diminish spending on advances in geophysics. Improvements are being seen however in geophysical equipment, although it is considered that the main improvement will be in the interpretation of data. Specifically, the trend will be towards integrating geophysical data into geological, geochemical and spatial data sets producing quality interpretation and providing low risk drill targets. Examples of the current trends in hardware and future directions are discussed below. In interpretive schemes there are very few examples of integrated interpretation but the possible trends will be discussed with limited examples.

Jan 1, 2000

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Batnasan, K Haga, A Shibayama, K Higuchi, H Takeuchi

High silica (SiO2), alumina (Al2O3), and phosphorus (P) contents in iron ore adversely affect the quality of iron products. The removal of those impurities from iron ore is an essential point in further iron ore processing. In this paper, the removal of P, SiO2 and Al2O3 impurities from iron ore by alkaline drying followed by reverse cationic flotation is discussed. The reverse cationic flotation experiments are performed using the iron ore samples without and with alkaline drying pretreatment. All other flotation conditions except pulp pH (4–12) and particle size distributions (-45 to -250 μm) are held constant. A typical collector and frother, such as dodecylamine acetate (DAA) and methylisobutylcarbinol (MIBC), are used in the flotation experiments. Alkaline treatment is conducted before flotation using sodium hydroxide at fixed conditions. The impact of alkaline drying on the performance of iron ore flotation is evaluated based on the removal rates of P and SiO2 + Al2O3, iron grade, and iron recovery compared with the iron ore flotation without alkaline drying (direct flotation). X-ray diffraction (XRD) analysis indicates hematite and goethite are the main minerals in the iron ore, which assays 62.8 mass per cent Fe, 0.232 mass per cent P, 7.1 mass per cent SiO2 + Al2O3 (total) determined by X-ray fluorescence analysis (XRF). Results indicate that a combined approach is more effective for removing P and SiO2 + Al2O3 impurities from iron ore than the direct processing technique because the maximum removal rates of P and SiO2 + Al2O3 are 48.2 per cent and 66.5 per cent from the alkaline dried iron ore when 8.4 per cent and 13.1 per cent from the non-alkaline dried iron ore.

Sep 18, 2023

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is an energy efficient way of grinding and a number of operations have utilised this in the design of their comminution circuits. Owing to the large flow of slurry through the mill that results from operating this way the grates and pulp lifters have to be designed to cope. However, the literature has little or no information on how grate and pulp lifter size and design are related to their ability to remove slurry from the mill. Over the last few years the JKMRC has been researching this area and has developed relationships between grate/pulp lifter design and flowrate capacity. At the same time it has determined the major causes of pulp lifter inefficiency and a solution to preventing this inefficiency (the Twin Chamber Pulp Lifter). This paper describes the models that have been developed through this program and uses industrial scale data to illustrate their accuracy. Results from the industrial trials of the Twin Chamber Pulp Lifter are also presented.

Jan 1, 2000

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By W J

Al ores arriving at the works which contain more than 3% sulphur, together with all sands and other fine residues, are delivered to the roasting department. Those that are in a coarse condition are first sent to the crushing plant, consisting of 15 in. x 9 in. jaw crushers and two No. 5 Krupp mills. The ore is here crushed through a quarter mesh screen. Any pyritic concentrates high in sulphur are given a preliminary roasting, to bring the sulphur contents down to about 12 % and the roasted material is delivered to the H. H. charge-making bins. Here the various ores, sands, residues, roasted pyrites, together with about 12 % of limestone, are made up into I-ton charges in hopper trucks with bottom discharge. The trucks are elevated by hydraulic lifts to a tramway running over the roasting furnaces, and the contents are dropped into hoppers over each furnace, from whence the mixture is fed into the centre of each furnace by means of a Challenge ore-feeder.

Jan 1, 1918

By D McInnes

Rather than look at the problems associated with sampling, this paper deals with the issue of sampling and blending to optimise revenue û predominantly in the mining industry. An example of the use of this methodology in the agriculture industry is also presented. Mining companies, in particular, are experiencing a boom in commodity prices and many believe the industry is in the middle of a æsuper cycleÆ. Production levels are being escalated dramatically to meet the demand coming from China and India. This in turn has further stretched the capacity of our rail and port infrastructure û resulting in significant shipping queues around most Australian commercial ports and increased demurrage costs for the producers. Mining companies are now looking for effective scheduling, planning and blending to maximise production and reduce demurrage charges û given the current infrastructure constraints. Mining companies can no longer use spreadsheets to run their business. This paper further looks at how these outcomes can be met by optimised blending using an integrated supply chain management system such as MineTrak together with effective sampling and analysis.

Jan 1, 2005

MR JOHN S Foxall wrote: Mr Clayton in his paper on the above subject (Proceedings, N.S. No. 34) made an assertion which should not be allowed to remain unchallenged. On the top of page 10 appears the following statement;- "By viewing the box at adepression angle of 45°, all the dimensions are disclosed and the box may be projected on isometric co-ordinates" and lower down on the same page:- "An isometric plan, being virtually a projection on a plane inclined at 45°, the nearer the dip approaches this figure so is the outline of the stoping more truly shown." Those statements embody an inaccuracy which would be misleading were an isometric plan to be constructed to suit a special case, ie the case of a mine whose lode dipped at 45°, or approximately 45° and it would be found that in such a plan the outline of the stoping would not be truly shown. The reason for this is that the depression angle at which an object is viewed in order to...

Jan 1, 1920

Scheduling mine development and underground construction has been the bane of most mine managersÆ lives at one time or another. Even though scheduling software has developed significantly over the last 20 years, mining projects continue to take far longer than expected to complete. It would appear that possession of a gleaming 1000 activity bar chart generated by the latest project management software and plotted in multiple colours offers no guarantee at all that any of those 1000 activities will be completed on time, let alone the project as a whole. The author has earned his æmasters in disastersÆ with more than one project running over time and budget. This paper describes some of his experiences in scheduling major mine development and construction projects and the lessons he has learnt along the way. In particular, the paper examines a range of key issues that mine schedulers must take into account when planning mining projects. The paper also examines the development of scheduling software and particular advance rates used in scheduling mine development projects in Australia.

Jan 1, 2000