Search Documents

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By Feilding C

Vitrinite of humic source (often designated as vitrinite A) is the maceral by which the rank of a coal ought to be determined. Therefore its recognition, and the precise identification of other vitrinites is essential. The majority of Australian petrologists are not differentiating between the vitrinite group macerals in maturation studies, the results of which have led to unexplained phenomena in coal characterisations and evaluation, such as 'reactive inertinites' and inaccurate predictions in petroleum source rock studies. The Callide coal has been chosen as a case study, with examples from other coals. The coal seams from the Callide Coal Measures show variation in the predominance of some macerals, indicating successions of environmental changes. The application of transmission electron microscopy (TEM) to the study of the Callide coal has enabled a better understanding of the nature and origin of some of the less understood macerals such as micrinite and vitrinite B. Two forms of vitrinite have been observed, each with a distinct reflectance range. The wood-sourced vitrinite A displays an average reflectance of 0.56 per cent, and a range of 05. - 0.7, implying a higher rank than the 0.49 per cent Ro total vitrinite reflectance recorded in previous publications. Vitrinite B is one of the most commonly-occurring macerals in the Callide coal. The lower-reflecting vitrinite B which forms bands, often several hundred microns in thickness, in TEM appears to be electron transparent lipid rich. Vitrinite B is interpreted to represent accumulations of leaves, and is believed to be a major source of hydrocarbons in Australian sedimentary basins. The Callide coal has entered the oil window, and oil has been generated from some exinite, cutinite, and resinite, as evident from the amber to light brown fluorescence of exinite and the presence of exsudatinite in cell cavities and cleats. However vitrinite B, the major potential source of oil, is seen under the microscope to be generating oil, thus placing this coal at the top of the oil window. Micrinite, the origin of which has been much debated, occurs as cell filling or infill of spaces between laminations in vitrinite B.

Jan 1, 1991

The twin iron ore islands of Cockatoo and Koolan are located in the spectacular setting of Buccaneer Archipelago off the Kimberley coastline of WA.Cessation of ore shipments from Koolan in 1993 ended 42 years of continuous mining activity which began with the first shipment of ore from Cockatoo in 1951.

Jan 1, 1993

By Buisman C. J N, Koch R. O

Soil and groundwater beneath the Budelco zinc production plant at Budel-Dorplein (The Netherlands) are contaminated with metals and sulphate. To avoid contamination of nearby drinking water aquifers in the very distant future, a geohydrological containment system (GCS) and a microbial treatment plant for extracted contaminated groundwater have been developed. As a first step in the design of the system groundwater data from over 150 wells and geological profiles were used to model geohydrological conditions beneath the site. Several configurations of water-extraction wells were deduced from the model. Data gathered during additional fieldwork were then used to improve the model. Finally results that were calculated for the various configurations were used to select an optimal groundwater containment system. Currently some 5000 m3/day groundwater are extracted from a combination of 12 shallow and deep wells. Heavy metals and sulphate have to be removed from the extracted water before it can be discharged into the river system or used as process water. Several water treatment methods have been studied and pilot-tested at the site. The preferred and selected process is based on the activity of sulphate reducing bacteria (SRB) and combines sulphate removal and heavy metal removal in one single step. The anaerobic bacteria reduce the sulphate to sulphide resulting in the precipitation of metal sulphides. A pilot plant gave promising results and a commercial-scale plant has been designed. The proposed design has been tested in a demonstration plant which included all main process units. Test results for all process units are presented. The collected information was then used to optimise the design of the commercial-scale plant. Special attention was paid to automation and safety items. Construction of the plant was finished in May 1992. Start-up, commissioning and operational experience are reported. The concentrations of metals and sulphate in the effluent of the SRB water treatment plant are well within the limits set by the authorities for discharge to public waters.

Jan 1, 1993

The discovery of gold mineralization at the Manhattan mercury mine, Napa and Yolo counties, California in 1978 was the result of applying a new exploration ore deposit model in a region previously unprospected for gold. This discovery, the McLaughlin gold mine, owned and operated by Home-stake Mining Company, is a classic epithermal mercury-hot springs-gold deposit currently producing approximately 7,776,000 grams of gold annually.The exploration program that led to this discovery was based on a mercury-hot springs-gold genetic model. The model was developed using basic knowledge of ore-forming processes plus careful field observations made during examination of many known precious metal districts in. the Western U.S.A. Theoretically, hot spring systems could host gold deposits and, indeed, gold in these environments had been recognized for years. However, at the time of the McLaughlin discovery, it was not known to occur in sufficient quantities to inspire geologists to explore hot spring systems specifically for gold. Field observations recognized the presence of hot spring deposits and mercury mineralization asso-ciated with precious metal districts, (Bodie, California being a type example), and this associ-ation prompted the development of a hypothetical model. Subsequent exploration activities were directed towards the examination of mercury mines and prospects as potential targets for gold deposits. The model envisioned hot spring deposits (sinter) containing mercury mineralization at the surface with anomalous gold values grading downward into significant ore grade gold values.

Jan 1, 1990

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

Current mine ventilation systems have evolved from simple, limited energy, series or multi split layouts motivated by low suction, slow running, surface fans. Concentration of coal production from fewer working places and ventilation splits, and varying needs, hazards and challenges, however, have led to substan- tial changes. Modern ventilation systems, therefore, are more complex, sometimes more interdependent on others, more energy intensive, and are founded on the use of multiple airways and greater suction, higher speed surface ventilators and often booster fans. Intensi- fication of output has resulted also in higher gas emission rates, the wide adoption of fire- damp drainage, and sometimes in particular problems such as spontaneous firedamp emissions. Some coal mines are subject to spontaneous outbursts of coal and firedamp. These and related matters and current practices and developments are leading to discernible trends, potential advances, and further changes in Practice.

Jan 1, 1983

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

By Grantham DL

ABS'TRACT For a number of years research efforts have been directed towards improving the efficiency of sampling and analysing coal mine roadway dusts. In the past decade the practicality of rapid, on site analysis of the incombustible content of these dusts using a radioactive technique has been receiving close attention both in Australia and overseas. Accurate measurement of the total incombustibles present is only possible by time consuming chemical methods. As the densities of the solid incombustible materials are greater than that of coal, they absorb a higher proportion of incident low energy gamma radiation than does coal. The amount of such radiation "back scattered" from mine dust samples is therefore inversely related to their average densities, and hence to their incombustible contents. This phenomenon can be used as a measure of incombustible content by employing an appropriately designed and calibrated instrument.

Jan 1, 1981

Modern plate tectonic reconstruction of Mexico and Central America shows that the southeast-extend ing Precambrian backbone of Mexico, together with the east-flanking accreeted Huastecan (Appalachian-Caledonian) orogenic belt, are geotectonic elements practically absent in Central America, except west-ern and northern Guatemala and Belize, and contrib-uted little to the mineral potential of the entire region.The gradual accretion of the Cordilleran oro-genic belt took place against the western-south-western margin of the Precambrian backbone, and its consolidation required several tectonic events from the medial(?) Paleozoic to the end of the Mesozoic. The striking features of this "long-lived" orogenic belt are the massive sulphide min-eralization in the upper Paleozoic eugeoclinal as-semblage, the widespread gold occurrence in quartz veins in the lower Mesozoic volcanics and related intrusives, the carbonate-hosted silver-bearing lead-zince deposits of the Mississippi Valley-type (or Pine Point-type) around carbonate banks within the Lower Cretaceous back-arc miogeocline, that de-veloped over the Precambrian backbone and deeply-eroded Huastecan orogenic belt, the massive sul-phide (Pb-Zn) deposits in the Upper Jurassic-Lower Cretaceous sequence, transitional from miogeocline to eugeocline, which carry high grades in silver, and the iron deposits in this transitional facies, which are described in the literature as related to dioritic intrusives of Late Cretaceous age. Central America, south and southeast of the Mota-gua-Polochic fault system, forms part of the in-ternal zones of this orogenic belt.

Jan 1, 1990

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

By Jancar T, de Guzman M M, Matthews B, Tu J. Y

The use of computational simulation to predict the performance of existing equipment or for the design of improved mineral processing equipment will be referred to as Computational Mineral Processing (CMP) in this paper. The emphasis will be on solving the governing equations for liquid solid flows in complex geometric domains to obtain, typically, the three-dimensional distributions of velocity and pressure for the liquid phase and the velocity and concentration for the solid phase. The underlying technology, computational fluid dynamics (CFD), is very well-developed in other industries (aircraft, car and chemical) and forms a vital part of product design and analysis. The subsequent design of improved mineral processing equipment may also involve finite element structural analysis (FESA). Computational fluid dynamics (CFD) and finite element structural analysis (FESA) are part of the generic discipline of Computational Engineering and Science (CES). Ciment and Scherlis (1993) define CES as `The systematic application of computing systems and computational solution techniques to mathematical models formulated to describe and simulate phenomena of scientific and engineering interest'. Increasing computer power (Kaufmann and Smarr, 1993), is a dominant factor determining the rapid growth of industrial utilisation of CES. This increase is happening at both the supercomputer and the workstation level. Indeed, today's typical workstation, a Hewlett-Packard 735, is as powerful as a CDC 7600, the leading supercomputer in 1970. Future computer architectures are expected to become increasingly parallel (Gartner Group, 1990) allowing a sustained performance of a teraflop (a million megaflops) to be achieved well before the Sydney Olympics in the year 2000. It is recognised that the modem development of most disciplines in the physical sciences rests on the three complementary strategies of experimentation, analysis and computational simulation. As the 21st century is approached the volume of computational simulation, both fundamental and applied, is growing dramatically and the role of experimentation is diminishing. In the area of equipment design, CES provides the following advantages over experimental testing and measurement: 1. lead time in design and development is significantly reduced; 2. CES can simulate conditions not reproducible in experimental tests; 3. CES provides detailed and comprehensive information; and 4. CES is more cost-effective and time-efficient. The ultimate benefit for industry is greater productivity and hence greater profitability. The broader issues in relation to CFD are discussed by Fletcher (1993b). In the five- to ten-year time frame, growth in computer power will make it practical to combine CFD and FESA with optimisation procedures to produce a design process that is almost fully computerised. It is expected that fully automatic

Jan 1, 1995