Search Documents

By M W. A Asad, E Topal, D S. S Sandanayake

Underground mine planning requires an optimal stope layout as a prerequisite for the definition of an optimal production schedule. The procedure to generate an optimal stope layout considers an orebody model and economic parameters as inputs. It evaluates all possible combinations of mining blocks and creates a set of stopes by satisfying the physical mining and geotechnical constraints. Thus, the procedure is computationally complex, and generating a solution to the problem is a challenge. This paper presents an implementation of a new heuristic algorithm that solves the stope layout problem. In two case studies, the algorithm achieves 11.2 per cent and 22.5 per cent superior solutions to the industrially available maximum value neighbourhood approach.CITATION:Sandanayake, D S S, Topal, E and Asad, M W A, 2014. Implementing a new heuristic approach to the underground mine stope layout problem, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Clarke

Commissioning of the Cannington processing plant began in October 1997. The nameplate capacity (of 1.55 million tonnes of ore per annum) was achieved relatively quickly. Since then (like many mines) the operation has strived to increase throughput and improve valuable metal recoveries, to offset declining head grades and lift the value of the operation. The processing plant now has the capability of treating over 3.2 million tonnes of ore per annum and in financial year 2005/06 the combined concentrate production exceeded 600 000 wet tonnes, approximately 80 per cent above concentrate output in the first full year of operation (at the design feed rate). This improved performance was achieved by making changes and additions to each of the major unit processes û primary grinding, flotation, leaching, filtering and paste fill preparation. The changes have included: adding a fines flotation circuit, expanding the grinding circuit, adding a pebble crusher, switching from continuous to batch leaching, building paste conveyors and decommissioning the column flotation cleaning circuits. This paper reviews these changes, outlines the current operating practices and discusses the challenges or opportunities that remain.

Jan 1, 2007

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By T Hicks

Designers of mining facilities play a significant role in defining the overall mine greenhouse gas emissions performance. This demands an appreciation of all the greenhouse gas emissions sources, including Scope 3 emissions, which will form an increasing fraction of the emissions as we transition our generation sources to renewable energy. Traditionally overland conveyors are designed to operate as fast as practical, and through this approach, achieve relative minimisation of: conveyor belt tensions; belt width; mechanical equipment masses; structural steel quantities; and concrete quantities. It is well understood that higher belt speeds reduce capital cost and improve project economics. Operating at higher speeds introduces operating costs through system energy losses and increased wear rates. This paper assesses the life cycle greenhouse gas emissions for a typical iron ore overland conveyor to demonstrate how the design criteria and engineering decisions impact greenhouse gas emissions and project economics. An analysis of the decarbonisation potential and project economics using a range of operational parameters has been completed, developing a marginal abatement cost for each system configuration, creating a basis for integration of low emission overland conveyor designs as part of the broader facility decarbonisation strategy.

Sep 1, 2024

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the"rate of extraction of gold. This probably is due to the activation of passive gold by.th,e. thallous ions'.''Lea'd, bismuth, and mercury salts, which should produce ' a, similai effect, fail to do so. It is postulated that'this latter result, together with'the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide. The use of thallous salts to reduce leaching time is discussed briefly.

Jan 1, 1964

By Smith I. W

Australia has, and faces, a growing problem with regard to the ability to meet the demand for liquid fuels from indigenous petroleum resources. The position for natural gas is better but there is no room for complacency. Since the coal resources are relatively extensive, interest in the prospect of producing liquid fuels from coal is in- creasing. The approaches to the production of gaseous and liquid fuels are briefly reviewed and the present status of coal conversion technology is discussed. Many problems remain to be solved and it is estimated (in the USA) that another 8-10 years will be required before any of the processes for liquid fuel production are considered sufficiently efficient and viable to go to a demonstration plant. Coals represent complex feedstocks and the effects of variations in coal properties on oil-from-coal processes are not fully understood. The thermal efficiencies of various coal conversion processes are considered in relation to their impact on coal requirements. The production of Australia's present requirement for liquid fuels by the only commercial process in operation would require a four-fold expansion in the local consumption of coal. Any assessment of the suitability of oil-from-coal processes currently under development overseas for Austra- lian coals and requirements must take heed of the differences in coal properties and motivation. The economic via- bility of processes for producing oil from coal will continue to be uncertain because of the large difference between the World price for crude oil and the actual production cost.

Jan 1, 1975