Search Documents

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By George C. Gibbons

ALMOST everyone in any of the five counties embracing the great East Texas field depends heavily upon oil for his living whether or not he actually owns a well or piece of royalty himself. Oil is a natural resource that, when utilized, spreads its benefits over a vast area and into many channels. Depending then almost entirely upon agriculture: what is now known as the East Texas oil field a decade ago had a scattered farming population. For many of its people, tomatoes and other vegetable crops coupled with the old southern stand-by of cotton, furnished an adequate living and a small cash surplus. Some farm families on the red hills, however, were not far re- moved from the sowbelly and black- eyed peas, or cornpone and potlikker, standard of living. Kilgore of that day, was a village of less than 850 per- sons. Longview, with just over 5000, apparently had reached the limit of its growth. Tyler was an overgrown farming town of around 17,000 persons, de- pending largely upon the agricultural income of Smith County and surrounding territory for which it was a trading center.

Jan 1, 1941

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By F. W. Maclennan

The following is a list of members who died in 1929. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year of Date of Biography Election Name Death 1929 Page 1922 Adams, Waldo Peck................................ June 2 September 435 1903 Argall, Joseph.................................... Nov. 1 1894 Austin, Leonard S................................. Oct. 30 December 580 1905 Bailed, Melbourne.........................Dec. 12 May* 280 1890 Barringer, Daniel M.............................. Nov. 30 February* 119 1895 Batchelleb, HENRr R.............................. Jan. 15 March 167 BINGHAM Charles E............................. 1923 Bibkett, E. H..................................... Apr. 23 August 394 1913 Bibbell, Robert W................................. Jan. 18 April 214 1926 Blackmar, Don C.................................. June 4 March* 189 1920 Bosworth, T. O.................................... Jan. 18 April 214 1894 Boucher, Arthur S..........................Jan. 6 May 257 1927 Brandenthaler, R. R.............................. Dec. 14 January* 64 1889 Bretherton, S. E............................... Oct. 4 December 581 1911 Brunton, F. K................ .. Aug. 17 1924 Brush, Charles F................................. June 15 September 436 1925 Cameron, Frank N........................May 16 July 349 1891 Chambers, Robert E.............................. May July 348 1908 Clark, J. Murray................................. Dec. 3 August* 407 1883 Clymer, edward T............................. Oct. 13 December 579 1914 Cofpey, George T................................. May 8 July 349 1901 Cooke, L. H....................................... Aug. 23 November 537 1915 Cousins, George W........................ June 30 February* 118 1886 Cowles, A. H...................................... Aug. 13 September 436 1892 Crane, Theron I............................. Nov. 2 December 579 1921 Crowell, Samuel B................................ Dec. 9 January* 64 1907 Curtis, Bracey.................................... Jan. 31 April 215 1895 de Batz, Rene........ ............... January March* 189 1928 Dines, Tyson S.................................... March May 257 1909 Dufourco, R. G............................. January November 537 1920 Ericsson, Eric A.................................. Apr. 4 April* 231 1920 Erlenborn, Willi....................... Nov. 10 March* 189 1888 Farish, John B.................................... Nov. 14 December 580 1891 Ferguson, Vincent........................... Mar. 8 May 257 1917 Finucane, T. R.................................... Mar. 22 February* 118 1921 Foch, Ferdinand................................... Mar. 20 1885 Foucar, Edouard I....................... Jan. 3 March 167 1880 Francklyn, Charles G............................. Jan. 11 April 214 1925 Friedl, Arthur J.............................. July 9 September 435 1894 Fuller, James W. Jr............................... April 4 1876 . Goodale, Charles W.............................. April 11 May 258 1912 Graybill, John..........................Dec. 11 June* 320 1887 Gritzner, F. A.................................. Mar. 26 July 394 1906 Gunther, C. Godfrey.............................. Deo. 26 February* 118 1900 Haggen, Edward A.............................. Apr. 22 October 488 1895 Hall, Benjamin M........................Nov. 19 March* 189 1913 Harper, Walter S................................. Feb. 15 August 394 1921 Hawley, William S................................ Apr. 20 June 298 1920 Herd, Walter ... . . . ..... Aug. 23 September 435 1889 Holt, Marmadtjke B............................... Dec. 26 February* 118 1928 Husk, Albert D .... ................June 9 December 580 1920 Hutchinson, S. Pemberton......................... Feb. 16 April 214 1926 Ivanoff, Constantine L............................ Mar. 7 June 298 1914 Jaeger, Frederick..... .............July 28 October 488 1891 Jennings, Robert E.......................Oct. 30 December 580 1922 Johnson, Homar L................................. Sept. 17 October 483 1927 Johnson, Homer H................................. Mar. 21 May 257 1918 Jones, Jesse L ..... ...............Jan. 22 April 214 1892 Jones, Thomas J................................... June 18 October 488 1883 JoOet, Cavalier H................................. Mar. 29 May 258 1881 Kennedy, John S . . . . ... ..........Apr. 22 August 394 1881 Kennedy,- Hugh.................................... May 23 September 435 1895 Kebvin, James H................................... September October 488 1926 Kkom, L. J........................................ Dec. 24 January* 64 1905 La Follette, Harvey M........................... Sept. 19 November 538 1920 MacDonald, Alexander............................ May August 394 1904 Marengo, Paolo................................... May 257 1925 Maxwell, Allison R............................... May 7 November 538

Jan 1, 1930

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California's population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California's electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

By Edward Keller

Jan 1, 1906

By James P. Kimball

Jan 1, 1881

By Orlando E. Romig

As metals and alloys are composed of an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. Previous Work The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.' He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and 11, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He pre- pared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By E. S. Leaver

The authors of the paper above mentioned have sent the following statement to correct erroneous com-ments and implications in their article with the re-quest that it be published: "In the above mentioned article the reference to Bendelari jigs is used in the generic sense as applying to the mechanically driven diaphragm jigs. No attempt was made to dif-ferentiate between the various machines as installed on different dredges. The Natomas Company use a jig of their own manufacture. The Yuba Company installed the Placer jig as manufactured by the Pan American Engineer-ing Company. "The Pan American Engineering Company also manufactures the Crangle jig under their own name. This is a diaphragm jig in which the pulsations are produced by intermittent flow of water through the patent Crangle Valve and it has no driving mechanism."

Jan 1, 1937

By R. R. Jones, R. W. Kraft

Zn-Mg2Znn eutectic alloys nzay freeze willr either rodlike or lanzellar rnorphology. Alloys with slighlly more than /he eutectic arrzount of rnagnesillrn usually contain three-cnned dendrjles of MgzZnll in a eutec-lic ttlulris. All three morphologies haue the same cryslallographic orientution relationship: (0UOl) zn - 11 (111) Mg2Znll and (2310)Zn 11(101) Mg2Znll, but u3ith different prej-erred groulth direclions. The lurnellae lo rods transifion in con/rolled ingols qf euleclic cotnposition occurs because lhe large kinelic undercooling due to MgzZnll minirrzizes /he ejj-ecl of the solid-solid inlerface energy. The eutectic morphology is influenced by the presence of lhree-nned dendrites 0-f MgzZn11 which may conlrol /he rricroslrccture by acting as nuclealion sites. In recent years there has been much interest in eutectic solidification and several theories have been proposed. One of the confusing factors is the existence of various morphologies in which the solidified phases may form. The lamellar microstructure seems to be most common in metal eutectics, and it has been claimed' that all regular eutectics should be lamellar if sufficiently pure. However, there still remain eutectic alloys which are not lamellar or which change their morphology as a function of growth conditions. The eutectic between zinc and the intermetallic phase Mg2Znll was chosen for this investigation because it has been found to solidify in more than one morphology. The diagram in anssen' locates the eutectic point at 3.0 wt pct Mg and 367°C. lliott gives 364°C as the eutectic temperature, leaving the phase compositions unaltered. Since the growth conditions determine the micro-structure of the solidified alloy, the factors controlling the transition from one morphology to another could be studied. The lamellae to rods transition is of particular interest. PROCEDURE Alloys were prepared from carefully weighed portions of 99.999 pct Zn and 99.97 pct Mg by melting in Pyrex containers under argon and casting into graphite boats. The resulting ingots were remelted under argon and solidified unidirectionally in a horizontal tube furnace at growth rates ranging from 2.0 to more than 50 cm per hr under a temperature gradient, measured over a 5-cm length, of 9" to 14°C per cm. The solid-liquid interface appeared to be planar at all growth rates although no attempt was made to confirm this by decantation or quenching. A few ingots were allowed to freeze uncontrolled. Most alloys were of the nominal eutectic composition, 3.0 wt pct Mg according to Hansen2 and lliott, but some contained as much as 3.35 wt pct Mg. Chemical analyses were not run since metallographic examination confirmed that the desired composition was achieved. Specimens were cut from the middle portion of the ingot normal to the growth axis, polished mechanically, and etched with 2 pct Nital. Suitable areas were selected for the determination of crystallographic orientation relationships by a tiontechniqueof described previously by one of the authors.4 The (2310) planes of zinc and the (8701, {944}? (1032) planes of Mg2Znll were found suitable for orientation determination; experimental error was on the order of 2 or 3 deg. RESULTS Three different morphologies were found in the unidirectionally solidified alloys: lamellar eutectic, rod-like eutectic, and a structure whose most predominant characteristic was the presence of three-vaned (cellular) dendrites of Mg2Znll. These dendrites were only found in alloys with more than the eutectic amount of magnesium. In some ingots fine hexagonal needles of Mg2Znll surrounding a core of MgZn2 were observed. They were probably due to incomplete alloying and seemed to have no effect on the eutectic morphology. In addition hexagonal spirals like those discussed by Fullman and wood5 and Hunt and acksonh ere observed in some ingots frozen without directional control. Both MgZZn,, and MgZnz were detected by X-ray diffraction in these alloys. Since the morphology could not be grown unidirectionally and no characteristic orientation relationship between the phases was found, further study was limited to the lamellar: rodlike, and three-vaned dendrite morphologies. Alloys of Eutectic Composition, No Dendrites. The mcrostructures of allovs with no three-vaned dendrites were either lamellar or rodlike depending on the growth rate. At rates below 10 cm per hr the morphology was lamellar, consisting of two sets of parallel plates intersecting at about 54 deg like the Mg-MgzSn eutectic described by raft.7 At growth rates faster than 14 cm per hr the microstructure showed rods of zinc in a matrix of MgnZnll, while intermediate rates yielded mixtures of rods and lamellae in small groups. The lamellar "grains" were often several millimeters in cross section, but contained small irregular areas which divided each grain into perfect islands 100 or 200 p in diam. Lamellae were parallel to each other throughout the grain in spite of these defects in the structure, Fig. 1. Rods, on the other hand, could only be produced in small groups arranged like fish scales and separated by irregular areas of appreciable thickness, Fig. 2. Alloys Not of Eutectic Composition, With Dendrites. In alloys with 3.1 to 3.35 wt pct ME,-. three-vaned dendrites bf MgzZnll were usually found surrounded by eutectic. At growth rates slower than about 10 cm per hr the dendrites were separated from each other by small areas of both lamellar and rod eutectic, Fig. 3.

Jan 1, 1969

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By GERALD H. HUTTON

SINCE the inception of dredge mining, the attention of engineers and operators has been directed primarily toward mechanical improvements and refinements calculated to, reduce operating costs and to increase recoveries. The result has been to develop an efficient excavating and value-saving machine, which, in some instances, has an actual capacity of 15,000 cu yd. per day. Steel hulls and superstructures minimize the risk of destruction by fire and lengthen the life of the plant. Dredges now restore, to some extent, agricultural possibilities to mined ground. Large buckets, with correspondingly heavy parts, are able to handle heavy wash and massive boulders. Mechanical weaknesses have been strengthened. The use of manganese steel in bucket lines and tumblers permits the application too the bank of a digging force that can be withstood only by solid material, such as rock, cement or frozen ground. Various alloys of steel have been applied to certain duties and experiments in their heat treatment are still progressing. Haulage by tractor or truck is in common use. Discarded and worn steel parts are repaired or rebuilt by the use of the oxy-acetylene flame and the arc-welding machine. Gold and platinum saving is more efficient, although still subject to improvement. Dredging for tin ore is in successful operation. Crews are now highly specialized and experience has developed improved methods of work; particularly in the manipulation of dredges to build levees of tailings and to leave open waterways where desired. To sum up by the distribution of overhead expense over several units, ground under favorable conditions can now be dredge-mined for 5)2 c. per cu: yd., in spite of the increase in cost of supplies, power, and labor during, the past few years. Improvements in prospecting methods, however, have not kept pace with mechanical developments. Standard practices of ; testing ground today produce only wide approximations of values; although they obtain information concerning the character of the deposit and bedrock. It is interesting to note that few important changes in the methods of ten years ago are .to be recorded; the latest comparisons between pros¬pecting results and mined recoveries-have been at such variance as to cause confusion to the operator, and, in a degree, the sacrifice of the confidence of the capitalist. On this account, and because the growing scarcity of dredging ground. demands closer calculations on the part of the engineer, this appeal for collaboration and

Jan 1, 1921

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman's Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By J. F. Mitchell, R. Bainbridge, E. A. Melvin

IN the fall of 1953, The Consolidated Mining and Smelting Co. of Canada Ltd. put into operation a completely new and modern plant for sintering the rather complex assortment of materials which comprise the feed to the Lead Smelter at Trail, British Columbia. This Lead Smelter is one section of an integrated metallurgical plant producing lead, zinc, silver, gold, cadmium and other metals. Since most of the incoming lead concentrate contains appreci- able zinc values, and most of the zinc concentrate similarly contains appreciable lead values, the cross-routing of residues or tails from the respective lead and zinc plants offers obvious advantages in recovery of metals, and has been practiced for many years. A disparity has existed, however, between the output of zinc plant residue and the capacity of the Lead Smelter to treat it, with the result that over the years a stock-pile of residue had been accumulating, and by the end of World War II had reached the formidable total of half a million tons. To treat this stock-pile, in addition to all current zinc plant residues and, of course, the regular quota of lead concentrates, became a prime objective of the Lead Smelter following World War 11. As zinc plant residue plays an important part in the operations to be discussed in this paper, some consideration of its

Jan 1, 1958

McCulloch, Leon.-Experiments with Sherardizing. Discussed by Fred. L. Wolf, Willis M. Peirce, Jesse L. Jones, O. W. Storey, David R. Kellogg, William H. Finkeldey, L. H. Marshall 2 Bassett, W. H. and Davis, C. H.-Spectrum Analysis in an Industrial Laboratory. Discussed by C. S. Brainin, C. H. Davis, W. H. Bassett, George K. Burgess, George K. Elliott, Leonard Waldo, Keivin Burns 8 Roast, Harold J. and Pascoe, Charles F.-Arsenical Bearing Metals. Discussed by Jesse L. Jones, William A. Cowan,. William K. Frank, William M. Corse, Harold J. Roast 10 Bain, Edgar C.-Crystal Structure of Solid Solutions. Discussed by Ancel St. John, Edgar C. Bain, Paul D. Merica 14 Peirce, Willis M.-Studies on the Constitution of Binary Zinc-base Alloys. Discussed by George K. Burgess, Willis M. Peirce, D. H. Ingall, J. L. Haughton, K. E. Bingham 16 Webster, William R.-Application in Rolling of Effects of Carbon, Phosphorus and Manganese on Mechanical Properties of Steel. Discussed by George B. Waterhouse, J. O. Liebig, Ralph H. Sweetser, H. T. Morris, F. D. Carney, W. P. Barba, John H. Nelson, George K. Burgess 19 Barba, W. P. and Howe, Henry M.-Acid Open-hearth Process for Manufacture of Gun Steels and Fine Steels. Discussed by W. J. Priestley, Haakon Styri, C. T. Patterson, Harry Brearley, W. P. Barba, George F. Comstock, Alexander L. Feild 24 Kellogg, David R.-Electrolytic Deposition of Iron for Building up Worn or Undersized Parts. Discussed by Jesse L. Jones, William Blum, C. R. Hayward, George K. Burgess, C. P. Perin, David R. Kellogg 33 McQuaid, H. W. and Elm, E. W.-Effect of Quality of Steel on Case-carburizing Results. Discussed by H. J. French and L. Jordan, W. J. Priestley, M. H. Schmid, A. E. White, H. J. Stagg and S. C. Spalding, Henry S. Rawdon, J. S. Vanick 35 Phillips, Arthur and Davenport, E. S.-Malleableizing of White Cast Iron. Discussed by Samuel Epstein, H. A. Schwartz, A. E. White, R. S. Archer.... 58 Priestley, William J.-Effect of Sulfur and Oxides in Ordnance Steel. Discussed by Harry T. Morris, William J. Priestley, C. P. Perin, James H. Gray, W. P. Barba, Haakon Styri, Frank D. Carney, W. L. Harbrecht, George F. Comstock, E. J. Janitzky 67

Jan 5, 1922

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943