Search Documents

By D. Cox, M. J. Duggin, L. Zwell

The carbides of approximate composition and Mn have been studied using X-ray diffraction techniques. Those carbides of the type (Fe,Aln)zC ave isostructural with cementite. The cell pararmeters a and c have minimum values at approximately 10 at. pd substitution of manganese for iron; no satisfactory explanation has yet been found for this phenomenon. The carbide fFeMn4)C has a monoclinic unit cell whose dimensions are close to those of ,11,15Cz A neu-troip-dij~ractiot~ study of (F'eAlrz4)C~ reveals that, like MnsCZ, it is isostructural with Pd5Bz. The iron and manganese atoms occupy the palladium atom sites, while the carbon atoms were found to have the same atomic coordinates as the hovon atoms. A neutrorr-diffraction study of indicates that the carbon-atom positions are very close to those occupied in (Fez.,ll/lr~,.3)C. In both carbides studied, tlre iron and manganese atomzs were found to be essentially randomly distributed, although, in the case of (Fe,.811fn1.2)C, it is possible that there may be a slight preference of manganese atoms for- the general (d) positions and a corresponding slight preference of iron atoms for the special (c) positions. It has been found that a complete range of solid solution exists between Fe3C and Mn3C at 1050°C,I although Mn3C becomes unstable when the temperature is reduced to 95O0C,' and can only be retained by rapid quenching. It is also known that a complete range of solid solution exists from Fe5Cz to M~SC~,~ although the stability range of carbides of the type (Fe,Mn)sCz as a function of the relative proportions of iron and manganese is not known. X-ray examinations of Oh-man's carbide3 and Spiegeleisenkristall,~ which have the approximate compositions (Fe3.67Mnl.33)C2 and (Fe3-,Mn,)C, where x lies between 0.4 and 1, respectively, have been made. The following carbides have also been studied: ] The lattice parameters determined during these investigations are listed in Table I. It is seen that carbides of the type (Fe,Mn)sCz have a monoclinic unit cell while carbides of the type (Fe,Mn)3C have an orthorhombic unit cell. It is evident that the variation of lattice parameters with manganese content is not linear for carbides of the type (Fe,Mn)3C. The coordinates of the atoms in (Fe2.7Mno.3)C have recently been determined by single-crystal analysis., The fractional atomic coordinates have been shown by Fasiska and jeffrey to be in good agreement withj those deduced from an earlier analysis of Fe3C by Lipson and etch.' However, it was impossible to determine whether iron and manganese atoms occupied ordered positions because of the small difference between the atomic scattering factors of iron and manganese. The atomic positions in Mn5Cz (Refs. 8 and 9) and Fe5C2 (Refs. 7 and 8) have been obtained only by comparisons made with the isostructural compounds P~SB~.' Since X-ray diffraction techniques were used in these investigations, accurate positioning of the carbon atoms, which have a low atomic scattering factor, was difficult. No attempt has been made to determine the atomic positions in the other carbides previously studied. It was felt that an investigation of the lattice parameters of a number of intermediate carbides of the types (Fe,Mn)sCZ and (Fe,Mn)& would be of interest. It seemed likely that a neutron-diffract ion study of such carbides would indicate whether ordering occurred between the iron and manganese atoms because of the large difference between the neutron-scattering cross sections of iron and manganese. It also seemed probable that such an investigation would provide a determination of the atomic coordinates of the carbon atoms. I) EXPERIMENTAL DETAILS Specimens, each weighing approximately 20 g, were carefully prepared according to the following proportions: The components were 500-mesh powders of 99.995 pct purity iron and spectroscopically pure carbon and a 200-mesh powder of 99.995 pct purity manganese. The component powders were intimately mixed by prolonged shaking, then each specimen was inserted into a spot-welded cylindrical container of tantalum foil, whose end was closed but not sealed. Each specimen in its envelope was then sintered at 1050° C for 24 hr in a thin-walled evacuated quartz capsule, such a time having been previously found sufficient for equilibrium to be attained.' Each specimen was then quenched in order to attempt to retain the high-temperature phase, as the literature indicates that transformations may occur on cooling. Debye-Scherrer X-ray photographs were taken of each specimen using a 114.6-mm-diam camera, Fig. 1, patterns 2 to 6. The exposure time was 6 hr using filtered iron radiation at a tube voltage of 40 kv and a tube current of 12 ma.

Jan 1, 1967

By E. F. Koch, J. L. Walter

oriented crystals of iron and iron with 3, 5, and 6.25 pct Si were rolled to reductions of 10 and 70 to 97 pct at room temperature. Similarly oriented crystals were deformed in tension. Dislocation substructures of the deformed crystals were observed by transmission electron microscopy to determine the effect of silicon on the formation of substructures. Pole figures were obtained to relate orientation changes to substructure. When rolled 10 pct, the iron crystals and the 3 pct Si-Fe crystals formed cells, 1 and 0.2 u in diameter, respecliuely. Cells were absent in the higher-silicon crystals. Extended dislocations and possible stacking faults were observed in the 6.25 pct Si-Fe crystal rolled 10 pct and annealed at 650°C. The stacking-fault energy was estimated to be 20 ergs per sq cm. Rolling to 70 pct resulted in the formation of sub-bands (0.9 µ wide) ill the iron crystals and transition bands (containing 0.2-µ-wide subbands) in the 3 pct Si crystals. No subbands formed in the 5 pct Si-Fe crystal until it was ankzealed. SliP occurred on (112) planes ill tension. The slip traces on the 3 pct Si crystal were wary while those on the 5 pct Si crystal wvere straight. The strain-hardening coefficient for the 5 pct Si crystal was nearly zero. Cells did not form, at least at elongations up to 10 pet. The results suggest that cross slip of iron is restricted by additions of silicon beyond about 3 pct possibly by formation of immobile extended dislocations. IN a previous paper' the authors described the substructures developed in (100)[001]-oriented crystals of 3 pct Si-Fe which were rolled to reductions of 10 to 90 pct at room temperature. At low reductions (10 to 20 pct) cells, approximately 0.2 to 0.3 ja in diameter, were formed. The cell walls consisted mainly of edge dislocations. With increasing reduction (up to 50 pct) the cells were seen to elongate in the rolling direction. In certain regions of the crystal there were significant reorientations which were characterized as rotations about an axis normal to the (100) or rolling plane. These regions were called "transition bands". The regions in which there were no reorientations were called ('deformation bands". At reductions of 60 to 70 pct the elongated cells in the transition bands became sub-bands separated by low-angle tilt boundaries with angles of disorientation of about 2 deg. The elongated cell structure in the deformation band was replaced by a general distribution of dislocations. It was noted that the width of the subbands in the transition bands remained 0.2 to 0.3 µ; i .e., the width of the subbands was the same as the initial cell diameter for reductions up to at least 70 pct. From this, and from considerations of the mechanism of formation of the transition bands,' it was concluded that the subbands evolved directly from the initial cells. In order to check this conclusion, it was decided to examine the relationship between initial cell diameter and width of subbands produced by large rolling reductions. Cell size is known to be dependent upon the temperature of deformation.2,3 However, preliminary experiments with 3 pct Si-Fe crystals indicated that the change in cell size with increasing temperature of deform,ation was not sufficient for the present purpose. On the other hand, cell diameters generally reported for iron deformed at room temperature2'3 range from 1 to 2 p, a factor of 3 to 10 larger than the cells in 3 pct Si-Fe rolled to 10 pct reduction,' indicating the possibility of a marked dependence of substructure (at least in terms of cell size) on the amount of silicon in iron. Thus, the investigation was enlarged to include the study of the effects of varying silicon content on substructure in lightly rolled as well as in heavily rolled crystals of iron and iron with 3, 5, and 6.25 pct Si. The crystals used in this study all had the same orientation, (100)[001], with respect to rolling plane and rolling direction. These were rolled to reductions of from 10 to 97 pct and the substructures determined by electron transmission microscopy in both the rolled state and after annealing. In addition, stress-strain curves were obtained from (100)[001]-oriented crystals of iron and 3 and 5 pct Si-Fe to determine the effect of silicon on tensile properties. The dislocation substructure of the tensile specimens was also determined for Samples pulled to 2 and 10 pct elongation at room temperature for comparison with the substructures produced by rolling. 1) EXPERIMENTAL PROCEDURE Crystals with 3, 5, and 6.25 pct Si were prepared by annealing 0.012-in.-thick sheets of high-purity Si-Fe in purified argon at 1200°C to effect growth

Jan 1, 1965

By A. J. Shaler

The subject of the mechanism of sintering has received much attention in the past few years, particularly since the beginning of the series of AIME seminars in powder metallurgy of which this paper introduces the fourth. In the first of these, F. N. Rhines1 brought together and discussed the available experimental data on the sintering of pure metallic powder, and succeeded in bringing to a sharp focus the attention of workers in this field on the established observations which a satisfactory theory must explain. Several other authors3,5,6 have, in the last few years, studied the phenomena that occur when cold metallic powders, loose or in the form of compacts, are first brought to elevated temperatures. Some workers' in the field of friction have recently studied the adhesion of solid metal surfaces when they are brought into close contact. These researches have indicated that several separate mechanisms operate simultaneously, at least during the first part of the sintering process. Some of them have been called transient mechanisms4 because they are in general not absolutely necessary to sintering. Powders may be so prepared and so treated that these transient phenomena do not take place during subsequent sintering. This does not mean, of course, that their industrial and scientific importance is any less than that of the steady-state phenomena. The latter are changes that go on during sintering no matter how the powders are made or treated; they cannot be divorced from sintering. One way to analyze the process of sintering into its component parts is perhaps to distinguish between these transient and steady-state phenomena. Some of the transient phenomena have been studied in the past few years. Huttig3 has shown that, when the temperature of metallic powder is slowly raised, the following events generally occur in order: (1) physically adsorbed gases are desorbed; (2) there is an atomic rearrangement of the surface, a sort of two-dimensional "surface-reciystallization"; (3) there is a breakdown of chemically adsorbed surface compounds; (4) there is a recrystalliza-tion in the volume of the metal. All these changes are shown by Huttig and his coworkers to be completed fairly rapidly at lower temperatures than those generally used in sintering and are therefore not a part of the mechanism whereby the density of a mass of powder continues to change after long heating at an elevated temperature. But the first and third of these changes release gases in quantities which may or may not help to control the steady-state mechanisms, depending on when the voids become isolated from the outside of the compact. Among the phenomena studied by Steinberg and Wulff,8 there is the effect on sintering of residual stresses arising from the pressing operation. They found that the lateral surfaces of a green compact of iron are under a longitudinal residual tension-stress of the order of magnitude of half the yield-point for solid iron. If the outside surface is in tension, the core must be under longitudinal compression. When the compact is heated, the surface residual stress is thermally relieved first, and the compact therefore initially expands in the direction of its axis. This is a transient phenomenon, if for no other reason than the possibility of sintering unpressed powders, as demonstrated by Delisle,9 Libsch, Volterra and Wulff10 and others.1 The subject of recrystallization is dealt with further in a separate section, in view of its prominent place in sintering literature. It, too. is one of these transient phenomena. Among the steady-state parts there may be distinguished the attraction between particles and its consequences, the spheroidization of voids in the compacts, and the densification or swelling of the compact. There is considerable evidence4,7 showing that cold metallic surfaces, when brought to within a few interatomic distances of one another, are attracted to each other by forces of the order of many thousands of pounds per square inch. A calculation, discussed in greater detail in another section, shows that this force changes but slightly when the temperature of the surfaces approaches the melting point. Actual measurements of forces of adhesion of this magnitude have been made by Bradley12 on some nonmetals, but none has yet been made on cold or hot metals. This force is of sufficient magnitude to cause some plastic deformation in powder compacts, as will be shown below. A second force of steady-state nature is due to the surface tension, which probably has the same origin as the force of attraction between surfaces.164 A paper by Udin, Shaler, and Wulff1,3 gives the results of precise direct measurements of its value for solid copper. The demonstration of the tendency for the surface tension to shrink a pore was long ago given by Gibbs.17 He showed that its effect on a curved surface between two phases is equivalent to a pressure perpendicular to that

Jan 1, 1950

By Murray F. Hawkins, W. J. Ainsworth

In all types of subsurface pressure gauges the extension which occurs in the pressure-sensitive element is a function of the difference between the external (well or calibration) pressure and the internal pressure within the gauge, rather than a function of the external pressure only. The internal pressure is near atmospheric and depends upon (a) the quantity of air sealed within the gauge at the time of calibration or measurement, (b) the quantity of moisture (liquid water), if any, sealed within the gauge, and (c) the temperature at which the calibration or well measurement is made. Part of this correction for the change of internal pressure with temperature is taken care of by the customary temperature coefficient of the gauge. However, part of it is not, and while this portion may be only a few psi, it is nevertheless predictable or preventable, and should be considered in precision measurements. ERROR NO. 1 If air is sealed in the gauge at the same temperature and pressure for both the calibration and the well measurements, the usual temperature correction will take care of any difference between calibration and well measurement temperatures. However, if air is sealed within the gauge at temperature T1 and pressure P1 at calibration but at temperature T2 and pressure P2 for a well measurement, because different amounts of air are sealed within the gauge in each case, the internal pressure at. or corrected to, calibration temperature Tr will he different by where all temperatures and pressures are absolute. The calibration temperature is used, and not the well measurement temperature, because the usual temperature correction reduces the well measurements to calibration temperature. The correction term as calculated by the above equation is separate from. and in addition to, the usual temperature correction. Example: T, = 540°R, sealing temperature at calibration P, = 14.7 psia, sealing pressure at calibration T2 = 460°R, sealing temperature at well P2 = 14.7 psia, sealing pressure at well Tr = 660°R, calibration temperature AP = 660 [14.7/460 — 14.7/540] = 3.1 psi While this error is small even under these somewhat maximal conditions, it nevertheless represents a practical situation which did occur, and which as a matter of fact gave rise to this note. Where AP is positive, as above, the correction is added to the measured pressure; where negative, subtracted from the measured pressure. This correction should also be considered in successive calibration runs where the gauge, for example, may be warm from a previous calibration at an elevated temperature. ERROR NO. 2 Where a small quantity of moisture (liquid water) is sealed within the gauge at atmospheric conditions, the increased vapor pressure of the water at higher well or calibration temperatures will cause an increase in internal pressure. This moisture will come presumably from condensation within the gauge following temperature changes, from moisture on the operator's hands, and from atmospheric moisture (rain, mist, fog, etc.). Calculation shows that approximately 0.2 cc of water (three to four drops) is sufficient to saturate the air within an Amerada RPG-3 Gauge at 160°F, at which temperature the vapor pressure of water is about 5 psia. As the vaporization occurs in a sealed volume, the increase in internal pressure will be in excess of this 5 psi. At higher temperatures the pressures will be higher; however more water will be required to saturate the air within the gauge. Some experimental work was carried out with an Amerada RPG-3 Gauge at 200°F fitted with a 1,000 psi element, both with a dry recording chamber and with a small amount of water added. The results directly proved the existence of the error due to the presence of moisture, and, it is felt, indirectly, due to the differences in sealing temperatures and pressures, as both effects may be ascribed simply to an increase in the moles of gas within the recording chamber. SUMMARY In precision measurements the error introduced by sealing the gauge during a well test at a different temperature and pressure from that of calibration may be corrected for by using the equation presented, or it may be prevented by taking care always to seal the gauge at near calibration conditions. The error introduced by sealing moisture in the gauge may be prevented by taking care to keep moisture out of the gauge, or by removing the moisture by either warming or evacuating the gauge. Both of these errors are independent of the range of pressure measurement and the type of gauge, and are in addition to the usual temperature correction. ACKNOWLEDGMENT Appreciation is expressed to W. B. Kendall, Geophysical Research Corp., Tulsa, Okla., who pointed out the error from differences in sealing temperatures during some winter work in Canada. ***

Jan 1, 1956

By S. G. Proctor, D. L. Baaso, W. V. Conner

A double crucible system was developed for I-g scale plutonium reductions. The equipment consists of an inner MgO crucible, an outer MgO crucible, and a stainless steel pressure vessel. The reduction charge is PIaced in the inner crucible and the annulus between the inner and outer crucibles is filled with a mixture of calcium and iodine. The exothermic reaction between the calcium and iodine in the annulus supplies the heat required for complete reaction of the reduction charge ana' good metal coalescence. Metal yields of 80 to 85 ,pct were obtained from I-g scale reductions and yields as high as 97.5 pct were obtained from 0.5-g scale reductions. The system was used to reduce charges containing as little as 0.1 g of Pu resulting in metal yields up to 90 Pct. THIN metal foils of highly enriched plutonium isotopes are used as targets for cross section and other measurements. The isotopes are separated in the calutrons at Oak Ridge and are very expensive to prepare. Often, only 1 or 2 g of material are available thereby emphasizing the need for a method of preparing these small quantities of metal. Procedures for 1-g scale plutonium reductions have been described, but these procedures require elaborate or expensive equipment. For example, the procedure described by Anselin et al.1 requires an inert atmosphere glovebox and induction heating equipment. The procedure described by Baker2 also uses induction heating equipment to obtain the recommended heating rates and liner temperatures. Baker's procedure also requires high purity PuF4 with very little PuO2 present. The procedure described in this paper resulted from a search for a simple and inexpensive method for making 1-g scale plutonium reductions. EXPERIMENTAL Equipment. The equipment required for the double crucible system consists of a pressure vessel, two MgO crucibles, a MgO crucible lid, and a resistance-heated, vertical crucible furnace. The crucibles were slip cast from high purity MgO and were supplied by the Coors Porcelain Co. and the Norton Co. The pressure vessel and lid were fabricated from 316 stainless steel. Materials. The PuF4 used for this study was obtained from the P1utoniu:m Metal Production Department at Rocky Flats. The PuF4 was prepared in a con- tinuous hydrofluorinator by reacting Pu02 with HF at 650°C. The isotopic composition of the plutonium was approximately 93 pct 239PU, 6 pct 240PU, and 0.5 pct 241PU. Some of this PuF, contained less than 1 pct Pu02 (Batch No. 6 and 7), while other batches contained up to 15 pct Pu02 (Batch No. 3). The chemical analyses of all the PuF4 used for this study is given in Table I. The calcium was 99 pct pure, AEC grade, and only that fraction which would pass through a 20 mesh screen was used. The I2 was USP grade re-sublimed I2 which was ground before being used. Procedure. Various charge compositions and methods for loading the double crucible system were tested. The optimum conditions for 1-g scale reductions are described below. The double crucible system was loaded as shown in Fig. 1. The outer crucible was placed in the pressure vessel and the annulus between them was filled with MgO sand. The inner crucible was placed in the outer crucible, supported by a layer of MgO sand in the bottom of the outer crucible. A mixture of 5.2 g of Ca and 25 g of I2 was placed in the annulas between the two crucibles. The upper portion of the annulas was filled with MgO sand. Next, a layer of a mixture of calcium and I, equal to 20 wt pct of the calcium and I2 used in the main charge was placed in the bottom of the inner crucible. The PuF, to be reduced was mixed with a 30 pct excess of calcium and 1 mole of I2 per mole of Pu and this mixture was placed in the inner crucible. The charge was topped with a layer of a mixture of calcium and I2 equal to 20 wt pct of the calcium and I2 used in the main charge. The pressure vessel was sealed with a flat copper gasket and was purged by alternately evacuating and filling with argon. The purge valve was closed and the vessel was placed in a vertical crucible furnace which was preheated to 950°C. The furnace was turned off after 20 min of heating and the vessel allowed to cool. Experience has shown that. this amount of heating is sufficient to assure complete reaction of the charge. RESULTS AND DISCUSSION The double crucible system has been used to produce plutonium metal on a 0.1- to 1-g scale. Reduction

Jan 1, 1970

By H. E. Mauck

The many factors that control bumping must be carefully studied for each coal seam where bumps occur, and specifications known to exclude bumping should be incorporated in the mining plans. This calls for complete knowledge of the seam's characteristics and its adjacent strata, and in many instances these characteristics are not revealed until the seam is actually mined. Pressure and shock bumps, the two general types, occur jointly and separately. In this discussion no differentiation will be made. Whether pressure or shock, they are treated as bumps, and both must be eliminated. Bumps in mines have occurred in several places throughout the coal fields of the world. A study of many of these occurrences indicates that geologic characteristics, development planning, and mining procedure have contributed. But more specifically, there are conditions usually associated with bumps: thickness of cover, strong strata directly on or above the seam, a tough floor or bottom not subject to heaving, mountainous terrain, stressed and steeply pitching beds, and the proximity of faults and other geologic structures. Mine planning should incorporate these known factors (not necessarily in order of importance): 1) Main panel entries should be limited to those absolutely necessary to ventilate and serve the mine. This reduces the span over which stresses may be set up that will later throw excessive pressures on barrier and chain pillars when they are being removed. 2) Barrier pillars should be as wide as practicable so that they will be strong enough to carry the loads thrown on them when final mining is being carried out. 3) Pillars should never be fully recovered on both sides of a main entry development if the barrier and chain pillars are to be removed later. The excessive pressures placed on the main chain and pillar barriers by arching of the gob areas can result in bumping when these barriers are being removed. 4) Full seam extraction is better accomplished by driving to the mine boundary and then retreat-drawing all pillars. If there are natural boundaries in the mine—such as faults, want areas, and valleys —retreat should be started there. 5) Pillars should be uniform in size and shape. The entire development of the mine should call for uniform blocks with entries driven parallel and perpendicular. Only angle break-throughs should be driven when necessary for haulage, etc. 6) For better distribution of rock stresses and reduction of carrying loads per unit area, both chain and barrier pillars should be developed with the maximum dimensions. 7) Pillars should be open-ended when recovered. If they are oblong, the short side should be mined first. Both sides of a block should not be mined simultaneously, but under no circumstance should the lifts be cut together. 8) Pillar sprags should not be left in mining. If they are not recoverable, they should be rendered incapable of carrying loads. 9) Pillar lines should be as short as practicable. (Three or four blocks are adequate). Experience has shown that rooms should be driven up and retreated immediately. The longer a room stands, the more unfavorable the mining conditions. This contributes to bumping. 10) Pillars should not be split in abutment zones (high stress areas lying close to mined out areas) and if slabbing is necessary, it should be open-ended. 11) Pillars should be recovered in a straight line. Irregular pillar lines will allow excessive pressures thrown on the jutting points. Experience has shown that the lead end of the pillar line can be slightly in advance. 12) Pillar lines should be extracted as rapidly as possible. This appears to lessen pressures on the line and render abutment zones less hazardous. 13) Extraction planning should call for large, continuous robbed out areas. Robbing out an area too narrow to get a major fall of the strata above the seam tends to throw excessive pressures on a pillar line. 14) Timbering in pillar areas should be adequate but not excessive. Too heavy timbering or cribbing is likely to retard roof falls and throw excessive weight on the pillar line. 15) Experience has shown that when pillar lines have retreated 800 to 1000 ft from the solid, bumps can occur. Because this distance may vary in different seams, impact stresses should be studied for each individual condition. In any event, extra precautions should be taken against bumps in this area. This list of controlling factors may or may not be complete. It probably is not, but it covers most of the problem's significant aspects. The question is whether or not bumping can be eliminated. The answer is that bumping can be minimized and possibly eliminated if these and other established factors are thoughtfully considered and incorporated in the mining and extraction plans. If a mine has already been developed or the pattern set so that little change can be made, then it will be necessary to adjust to the most nearly practicable system that can incorporate the known factors.

Jan 1, 1959

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

By T. B. Massalski, H. W. King

An hcp phase may be induced by cold working the ß&apos; phase of the Ag-Zn system. This phase reverts to ß&apos; on subsequent aging. No phase change occurs on cold working the o phase, but ß&apos; is formed when the deformed alloy is subsequently aged at room temperature. It is concluded that for alloys near 50 at pct Zn the ordered bcc ß&apos; phase is the equilibrium structure at room temperature. WhEN the disordered bcc ß phase of the Ag-Zn system is cooled to temperatures below 258o to 274oC, it transforms to a complex hexagonal phase <o.1,2 The nature of the o ß=o transformation has been the subject of some discussion,2&apos;3 and the structure of o has been described in detail.&apos; The latter phase appears to be stable on aging at room temperature but decomposes following cold work. When alloys containing approximately 50 at. pct Zn are rapidly quenched from the 0 phase field, the ß ? o transformation may be suppressed; but the ß phase undergoes an ordering reaction (ß ? ß&apos;). The ß&apos; structure may also be obtained as a result of cold working and aging at room temperature.4 Kitchingman, Hall, and Buckley4 have suggested that the decomposition of (o following cold work proceeds in two stages, (o ? ß followed by ß ? ß&apos;, but did not confirm this by experiment. When the ordered &apos; phases in the systems Cu-Zn5 and Ag-Cd6 are cold worked, they become unstable and transform to a close-packed hexagonal phase (( ) indicating that when order is destroyed in a ß&apos; structure the close-packed hexagonal phase may in many cases be more stable. It thus became of interest to study more closely the effect of cold work and annealing on the stability of both the ß&apos; and o phases in a Ag-50 at. pct Zn alloy. Predetermined weights of spectroscopically-pure Ag and Zn, supplied by Johnson and Matthey, were melted and cast under 1/2 atm of He in transparent vycor tubing. The ingot was homogenized for 1 week at 630°C and quenched into iced brine. Since mechanical polishing was found to induce a phase change, sections were first polished at room temperature, sealed in tubes under 1/2 atm of He, reannealed for several days at 630o or 200°C and then quenched into iced brine. Sections of the alloy thus prepared were found to be homogeneous when examined under the microscope. The sample quenched from 630°C (ß -phase region) was pink in color, whereas the sample quenched from 200°C (o-phase region) was silver. The latter sample showed the characteristic hexagonal anisotropy when examined under polarized light. Filings of the alloy were examined at room temperature, after various heat treatments, using an RCA-Siemens Crystalloflex IV diffractometer with filtered CuKa radiation. The X-ray reflections from flat powder specimens quenched from 630o and 200°C and sieved through 230 mesh were recorded graphically at a scanning speed of 1/2 deg per min. The resultant patterns are shown in Figs. 1(a) and 1(b) and may be identified as those of the 8&apos; and <02 structures respectively. The lattice parameter of the ß&apos; phase was determined as 3.1566Å.* This value compares very well withthatto be expected for a 50 at. pct Zn alloy from the data of Owen and Edmunds? and indicates that no loss of Zn occurred during casting. In order to study the effect of cold work upon the ß&apos; and o phases, filings made at room temperature and sieved through 230 mesh were mounted immediately in the diffractometer-i.e., without a strain-relief anneal. Changes in structure on subsequent aging were followed by scanning repeatedly over the regions of the low index reflections of the ß&apos; and o structures-i.e. , 28 from 35 to 44 deg. Immediately after filing the 8&apos; specimen, additional diffraction peaks were observed in the low-index region of the pattern, as shown in Fig. 1(c). These additional peaks do not coincide with those of the o structure, Fig. l(b), but may be indexed as the (10.0), (00.2), and (10.1) reflections of an hcp phase (<) with nearly ideal axial ratio. However, this hexagonal phase appears to be very unstable since within a very short time at room temperature it reverts back to the ordered ß&apos; phase, the reversion being complete within seven hours. The 5 ? ß&apos; reversion reaction is, therefore, very similar to those already reported in Cu-Zn5 and Ag-Cd6 7&apos;alloys. The action of filing caused the deformed surface of the originally pink ingot to become silver in color, indi-cating that the ( phase possesses similar reflecting properties to the o phase. Hence, the subsequent

Jan 1, 1962

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By Robin O. Williams

AN investigation has been made of the Ni-Cr system for the purpose of elucidating certain points, namely the nature of aging in both terminal solid solutions and the nature of the phase diagram. Information pertaining to solubilities and precipitation has been obtained. Experimentation Five alloys, Table I, were arc melted in a cold copper crucible using electrolytic chromium and car-bony1 nickel, both dry hydrogen treated. These 100 g buttons were homogenized 24 hr at 1300°C in dry hydrogen and air cooled. Powders were prepared by filing or pulverizing and subsequent heat treatment was done in vacuum or helium using titanium chips as a getter. Powder of —80 mesh was filed from the 60 pct Ni alloy quenched from 1000°C and was sealed in silica under vacuum using a 250 °C outgassing. After aging as indicated in Table I1 the lattice parameters were measured on the quenched samples using the standard cos" 6 extrapolation. These parameters are considered accurate to roughly 0.0001A. In all cases chromium lines of 2.8812 ± 0.0005Å at 30°C were found. Drastic quenching from sufficiently high temperatures produced very sharp body-centered-cubic lines in the first four alloys without indications of transformations. Temperatures to 1250°C were used. Solid samples less than 1/16 in. thick were quenched in water without transformation and the powders could be adequately quenched in small helium filled thin wall silica tubing using a water quench. For those powder samples which were quenched from the two phase field the relative intensity of the body-centered-cubic lines and the face-centered-cubic lines were estimated and extrapolated to give the indicated solubility data in Fig. 1. The data for the two higher alloys were somewhat limited, the plotted points being the lowest temperature where no nickel phase was found. Neither filing, abrading, pulverizing, nor cooling to —190°C produced any new diffraction lines for solid samples quenched from the single phase region, nor did the character of the body-centered-cubic lines change Single phase body-centered-cubic powders likewise did not change on cooling to —190°C. Also, samples which had some precipitation due to inadequate quenching showed no additional changes under these conditions. The first change apparent by X-ray diffraction form samples quenched almost fast enough to prevent precipitation was the diffuseness of the body-centered-cubic lines, particularly on the low angle side, For slower cooling rates the diffuse face-centered-cubic lines appeared. Work on the large grained castings showed profuse streaking through some of the Laue spots while oscillating patterns showed broad body-centered-cubic and face-cen-tered-cubic lines as well as some new lines. For the 23.6 pct Ni alloy the new lines corresponded to 2.16, 1.96, and 1.86A and were more similar in character to the face-centered-cubic lines than the body-centered-cubic lines. Samples which were air cooled gave only face-centered-cubic and body-centered-cubic lines which were still broad. One pattern indicated that face-centered-cubic (111) plane was parallel to a body-centered-cubic (110) plane. For those samples which were examined by light microscopy there were details which were not resolved. However, varied and beautiful structures were obtained. Fig. 2 is of an alloy quenched in a helium filled silica tube from the single phase region and shows particles associated apparently with dislocations which are arranged in low angle boundaries. Finer, general precipitation has also taken place within the grains. Figs. 3 to 5 show the variety of structures produced in these alloys on continuous cooling. It appears that there are four distinct modes of precipitation as evidenced by these, figures. Annealing these structures at higher tem-peratures in the two phase field gives structures as shown in Fig. 6, which shows nickel plates in the chromium matrix which reprecipitated nickel on a much finer scale of the final quench. Lower annealing temperatures and shorter times naturally give finer plates of the nickel-rich phase. Samples of the first four alloys were annealed for appreciable times between 900º and 1250°C and gave structures like Fig. 6. The relative amounts of the two phases were measured and extrapolated to give solubility data as indicated in Fig. 1. The point at 1250°C was deduced from data of Oxx.1 These and most of the other samples were checked for ferromagnetism but none was apparent. In fact, it appeared that the magnetic susceptibilities were not more than three times that for paramagnetic chromium. Discussion In Fig. 1 it is seen that the solubility of nickel in chromium can be represented by a slightly curved line on the usual log X vs 1/T plot, These data are believed to be accurate to roughly 5 to 10º. There is only fair agreement with the data of Taylor and

Jan 1, 1958

By Paul A. Taylor

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance. Substantial progress has been made in classifying different types of these deposits according to general features, internal structure, mineralogy, and origin. In some cases it has even been possible to block out tonnage reserves in advance of mining. It is still easy, however, to make highly erroneous predictions after a preliminary examination of a pegmatite prospect. Pegmatites are important to the economic well being of the country and to its military security. They furnish virtually all the feldspar, strategic mica, beryl, columbium, tantalum, and caesium utilized in the United States, as well as sundry other minerals and significant amounts of lithium and rare earth minerals and gems. With the exception of vermiculite, occasional ilmenite-rutile, and perhaps soda-lime feldspar and garnet deposits, basic pegmatites are of little economic importance. Consequently in this paper, as in common parlance, the term pegmatite generally relates to coarsegrained acidic rocks or what is aptly called giant granite. Available data indicating the size and importance of the production and trade in specified pegmatite minerals are summarized in Table I. Geological Features Much of the latest thinking on the economic geology of pegmatites is now available in a 115-page monograph&apos; by a group of experts who participated with geologists of the Federal Geological Survey in the widespread wartime investigations. Doubtless the most significant feature of the monograph is indicated by the title, The Internal Structure of Pegmatites, but it also contains a vast amount of other new information and includes the assimilated concepts of many earlier writers, whose works are given in a comprehensive list of references. The shape, size, attitude, and continuity of many pegmatite bodies is controlled by the structure of the older rocks in which they occur. If the older rocks are easily penetrated, e.g., biotite schist, most of the pegmatites in a given district will be found outside the parent granite mass as exterior pegmatites. Marginal pegmatites are more prevalent if the older rocks are massive, unsheared, and sparingly jointed. Networks of pegmatites are abundant in highly-jointed rocks. In strongly foliated schists the bodies are usually lenticular, whereas in highly-folded areas they assume tear drop, pipe or pod-like, bow-shaped, or sinuous forms. Jahns2 recognizes five major shape classes: l—dikes, sills, pipes, and elongate pods; 2— dikes, sills, pipes, and pods with bends, protuberances, or other irregularities; 3-—trough-or scoop-shaped bodies with or without complicating branches; 4—bodies with the form of an inverted trough or scoop; and 5—other bodies, including combinations of the above and miscellaneous shapes. Many pegmatite deposits are scarcely big enough to be recognizable as such. Most of them, in fact, are small tabular deposits less than 4 in. wide and usually without economic concentrations of minerals. On the other hand, some pegmatites are more than a mile long and over 500 ft wide. The ratios of length to breadth range from 1 : 1 to 1 : 100. Although the vertical dimension bears no invariable relationship to strike length, tabular deposits or large lenses are often symmetrical enough to show nearly as much continuity down dip as in their horizontal extension, and some pipes or pods are amazingly persistent in the vertical plane. Small pegmatites often string along a fairly definite trend line; in a given district major bodies may lie roughly parallel, and where only a few of them do not, the erratically disposed bodies generally differ in composition from those conforming to the regular pattern. This does not apply, however, in all districts. Characteristically, pegmatite veins pinch and swell or split into branches. When they pinch out entirely it is often possible to find a new body by prospecting the extension of the strike or dip, but the chances of finding a hidden deposit are ordinarily too uncertain to justify much subsurface prospecting. Diamond drilling may yield valuable information as to the continuity of known deposits whose upper portions are well-exposed. Some deposits, in fact, can be proved up for hundreds of feet by surface trenching and then intersected by drill holes at various depths like any other vein-like deposit. Others twist and branch, apparently defying all efforts to explore them short of actual mining.

Jan 1, 1954

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,&apos; wire of some bcc metals,&apos; and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4&apos;5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,&apos; but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By G. P. Conard, R. C. Hall, J. F. Libsch

The 50 pct Fe-50 pct Co alloy undergoes a transformation from disorder to an ordered structure of the CsCl type reportedly in the vicinity of 732OC. During this process, the coercive force goes through a maximum, apparently as a result of strains associated with the coherent nucleation and growth reaction. This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction, which is associated with annealing to a high degree of order with the continuous application of a magnetic field. The increase in ratio can be explained on the basis of a decrease in 90&apos; domain boundaries and, perhaps, by an increase in anisotropy resulting from lattice distortion. THE 50 pct Fe-50 pct Co alloy undergoes a disorder-order transformation which has been reported to occur in the vicinity of 732°C1,2 The ordered structure is the CsCl type.&apos; This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction as a result of heat treatment in a magnetic field, sometimes called a response to magnetic anneal.&apos;-&apos; The purpose of this investigation was to study the course of the ordering reaction, the nature of the response to .heat treatment in a magnetic field, and the relation, if any, between ordering and the response. Procedure The method of approach in this investigation was to produce an initial structure as completely disordered as possible and then gradually to order the alloy by isothermal anneals at various temperatures under different conditions of the applied magnetic field. Magnetic, magnetostriction, and X-ray analyses were of primary importance in determining the property and structural changes resulting from the isothermal anneals. Rings of the 50 pct Fe-50 pct Co alloy were prepared from the elemental powders by a powder metallurgy technique, further details of which may be found in ref. 7. The initial structure was produced by annealing the specimens for ½ hr at 1000°C, cooling to and holding for ½ hr at 900°C (in the a range above the ordering temperature), and water quenching. Isothermal anneals were performed at 600°, 675°, 720°, and 740°C. For example, rings were heated to 600°C, held for a predetermined period of time, and cooled by natural cooling at a rate slightly slower than an air cool (average of 20" to 25°C per min). The tests (magnetic, etc.) were made after each heat treatment. All high temperature treatments were performed in a purified hydrogen atmosphere. The treatments at the various temperatures were carried out under one or more conditions of an applied field including 1—no field, 2—field of 20 oersteds applied on cooling only, and 3—field of 20 oersteds applied continuously during heating, holding, and cooling. Magnetic measurements were made using the standard Rowland ring technique8 with a maximum field strength of 100 oersteds. The magnetization curve, induction at 100 oersteds (B.), residual induction (Bt), and coercive force (Hc) were determined. All magnetic analysis data were based on an average of the results from three rings. A strain gage technique9 as used for the measurement of magnetostriction. The X-ray determination of the relative amount of ordered phase present was made on the ring specimen used for magnetic measurement. This was done by the back-reflection method using a rotating specimen (because of the large grain size) with unfiltered CoKa radiation and a 7 hr exposure time. Intensity measurements of the ordered line (300) were made by comparing visually the films so obtained with standard films prepared by exposing for different lengths of time a specimen given a long time anneal (high degree of order). Results In all instances the saturation induction (induction at 100 oersteds) was found to increase slightly with annealing time. This effect was small and appears to be the increase in saturation induction to be expected on ordering.10-13 The residual induction behavior was markedly influenced by the field condition during annealing, Figs. 1, 2. For the condition of no applied field, the ratio of residual to saturation induction remained essentially constant for short annealing times but showed a significant increase at longer times. With increasing annealing temperature, less time was required to produce this increase in the ratio. In the case of the 600°C anneals, the increase did not occur until approximately 20 hr, Fig. I, while on annealing at 740°C the increase was immediate, Fig. 2. Slight decreases in the ratio may be observed at 100 hr for specimens treated at 720°C and at 1 hr for those treated at 740°C. Specimens annealed in a field of 20 oersteds showed a residual to saturation induction ratio consistently higher than that for the specimens annealed without the field. The first anneal with the field (¼ hr) caused an abrupt increase in the ratio at all temperatures; thereafter, the increase in the ratio was generally similar for specimens annealed

Jan 1, 1956

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By R. Maddi, I. R. Kramer

The delay time for the initiation of slip was studied in single crystals of a brass, aluminum, and ß brass. A delay time for slip was found in ß brass when the specimens were tested below room temperature; however, one was not found for a brass or aluminum. A general theory for the existence of the brittle transition temperature is proposed. A LTHOUGH a considerable amount of effort has A been devoted to the study of the deformation and fracture of single crystals, the vast majority of the work was concerned with static tests or with tests carried out at relatively slow strain rates. The necessity for the study of a possible incubation time for slip becomes apparent when the various theories which have been postulated for the elucidation of the mechanism of slip are considered. The existence of an incubation period would strongly indicate that slip occurs by a process of nucleation and growth; whereas the absence of an incubation would present rather convincing evidence that slip occurs by a cataclysmic process. In addition to shedding light on the process of plastic deformation, an understanding of the early stages of plastic deformation may be helpful in finding an explanation for the brittle behavior of the body-centered metals under certain conditions. It is well known that these metals, such as iron, molybdenum, tungsten, ß brass, etc., will become brittle as the test temperature is lowered or the strain rate is increased. In spite of the fact that this subject has received considerable attention since the turn of the century, no adequate theory exists today which explains the phenomenon. In the ductile temperature range the metal breaks with a "fibrous" fracture after considerable slip has taken place. In the brittle temperature range the metal fails essentially by cleavage on the {loo) planes: however, some plastic flow is always present even in the most brittle fractures. It is possible, as will be explained later, to ascribe this brittle behavior to the length of the incubation time for slip. Clark and Wood,&apos; using polycrystalline metals, showed that a delay time existed for the yield point in mild steels and that the delay time depended upon the applied stress. These authors stated that the delay time was observed only with those materials for which the stress-strain curve showed a definite yield point. In their work only the mild steel specimens exhibited a delay time at the yield point, while the other materials studied-type 302 stainless steel, SAE 4130 normalized steel, SAE 4130 quenched and tempered steel, 24s-T aluminum—did not show a delay time. These authors&apos; in an extension of their work, found that as the temperature was lowered the delay time was increased. It is, then, the purpose of this investigation to measure or to set an upper limit on the delay time for plastic flow in single crystals of a brass, aluminum, and ß brass. The delay time will also be studied as a function of temperature. The incubation time may be measured by determining the length of time the specimen will support a stress without slip occurring when the stress is greater than the static critical resolved shear stress. In order to accomplish these measurements use was made of a pendulum which was so designed that a single crystal specimen could be placed at various positions along its length. When a pendulum is struck by another pendulum of the same length, an elastic wave is transmitted down the bar with the velocity of sound in the material and is reflected from the far end of the bar. The reflected wave then travels back and unloads the stress until it reaches the impacted end of the bar and the two pendulums separate. The length of time that the specimen is subjected to the stress is equal to the time it takes for the stress wave to travel twice the distance from the specimen to the end of the bar. The stress applied to the specimen is governed by the velocity of impact of the two pendulums. The stress at which the specimen first suffers plastic: deformation was determined in these experiments by examining the specimen under the microscope for the first appearance of slip lines and by measuring the residual strain after each impact. In these experiments the critical resolved shear stress was approached from the low stress side and no attempt was made to determine it exactly. To determine it exactly, it would have been necessary to find that stress at which slip would have just started. However, since the stresses were increased in rather small increments the critical stress is believed to be approached rather closely, as will be seen from the experimental results. The critical stress will be taken as the highest stress obtained before the onset of plastic deformation. The stresses

Jan 1, 1953

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley&apos; in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By Tell Ertl

TODAY&apos;S mining industry is witnessing a transition in labor utilization. The drill-jumbo operator, the mucking-machine operator, the blasting crew, the scaling and timbering crew are all specialists. The all-around miner is rapidly disappearing. As mechanization has resulted in a higher order of underground skills; specialization of labor has been a natural consequence, as has the need for more supervision and engineering. Mines now are cleaner, neater, safer, and have a greater productivity per man-shift than ever before. Nothing spectacular like the continuous miner has yet come to the underground metal mines, but t a gradual improvement in methods, equipment, and technical knowledge is achieving the increased efficiency. With the exhaustion of the rich ores and large profits and who-cares-about-the-costs, mining has become a business; that of producing low value ores at costs below selling price. Charles A. Chase, patriarch of Colorado mountain mining men, manager of the Shenandoah-Dives, was one of the first to preach and prove his preachings that mining is a business. He has been mining a lead-copper-zinc-gold-silver ore, much from elevations above 1.3,000 ft, for a quarter century without a shutdown.-The ore is of such low value that most engineers and investors still would consider it foolhardy. Yet he has kept Silverton, Colo., alive, has paid wages without a lapse, has produced $25 million of new wealth and maintained a steady return to the investors. This type of responsibility is increasingly apparent in the mining business and is one feather that can be worn proudly. .Much emphasis is being placed on improving, the productive mining operations-breaking, loading and transportation. Breaking in underground metal mining is done by drilling and blasting. To the writer&apos;s knowledge, no chain or rotary-type machine has been developed for mining strong, abrasive rock. Drilling Percussion drills are still the standard drilling machines underground. Diamond drills, that: were the rage a decade ago for drilling long holes, are being superseded by the rock drill. The development of the hard abrasion-resistant carbide bit permits full-gage long holes to be drilled by percussion drills at a lower cost than diamonds. The change in the use of percussion drills is chiefly in the method of mounting. The column and arm are disappearing and the jackleg and rubber-tired or track-layer jumbo mountings are taking its place. At the Homestake mine .lightweight jackhammers mounted• on pneumatic legs using 7/8-in. hexagonal drill. rods and 1 1/2-in, tungsten-carbide detachable bits have been found more portable and maneuverable. They have less air consumption, lowered, dynamite consumption, and more footage and tonnage per man-shift than with 3 1/2-in. drifters on a column mounting. Drills now are mounted on longer feed carriages, drilling up to 20 ft without changing steel. These mountings result in great savings because the driller can set up quickly, drill the entire depth of the hole without changing the drill rod or bit using carbide and one-use bits, and can move his machine quickly to the next hole. One man to the machine is becoming general practice. The result is longer rounds rounds drilled at a lower cost than the previously used short rounds. A jumbo developed in the Tri-State can be extended to mine ore left in the roof up to 65 ft above the floor. Drill-rod life was formerly considered to be about 250 min of actual use. The increase in the drilling time per rod per day has gone up considerably with the development of the jumbo and the long-feed carriage, resulting in which is apparently more rod breakage., Consequently, a great deal of research is being done in the attempt to develop an alloy-steel rod with longer service life to offset the greater cost. Some reports indicate that alloy steel or Swedish steel results in cheaper drilling than conventional drill rod. However, several tests have shown only slightly increased life for alloy drill rod. Undoubtedly, the blow of the rock drill, the length of the drill rod, and the resiliency of the rock being drilled are important factors in the life of drill rod, so it follows that alloy steel might work well in some mines and result in no savings in others. The bit forged on the drill rod is seldom encountered and steel detachable bits are not as common as in the recent past. The one-use bit is gaining popularity because of. the difficulty in rehardening reconditioned steel bits satisfactorily. It is thought that the, carbie-insert bit is most applicable to drilling hard &apos;rock&apos; where the steel bit is unable to drill out a full change, for instance, in extremely abrasive

Jan 1, 1952

By R. E. Smallman, I. Milne

The deformation behavior of single crystals of Nb-Mo alloys has been investigated with particular reference to the influence of composition, orientation, and temperature. Strong solid-solution hardening was observed reaching a maximum at the equiatomic cotrlposition and can be attributed to the difference in atomic size between niobium and molybdenutrz. Changes in the form of stress-strain curve, as shown by a high work-hardening rate and restricted elongation to fracture, were observed at a composition of Nb-85 pct Mo and are attributed to the presence of MozC DreciDitate. Conjugate slip was only extensive in dilute alloy samples; at the 50/50 composition deformation rnainly occurred by primary slip, and the onset of conjugate slip gave rise to failure by cleavage on (100). The variation of yield stress of Nb-50 pet Mo with orientation was consistent with slip on (011)(111) slip systems. The temperature deperndence of the yield stress between -196" and 250°C was similar to that of pure bcc metals, but at a much higher stress level; no evidence for twinning %as found. IN recent years the deformation behavior of various pure metals in groups VA and VIA has received considerable attention, but surprisingly little work has been carried out on binary alloys made by mixing metals from the two groups. Such an investigation would be of interest since single crystals of metals of group VA have been shown to deform characteristically with a multistage deformation curve1"3 while a parabolic type of deformation curve has been reported for most of the group VIA metals.4&apos;5 It has been suggested by Law ley and Gaigher~ that the difficulty encountered in obtaining multistage deformation curves for molybdenum in group VIA was possibly because of the presence of a microprecipitate of MozC which they observed even at carbon contents as low as 11 ppm. Recently a multistage deformation curve has been reported for molybdenum ," although the stages are not so definitive as those for group VA metals. The binary alloys of the particular refractory metals which have been investigated in single-crystal form include Ta-w,&apos; Ta- Mo,&apos; and Nb- Na." While a large amount of hardening was observed for alloys of the Ta-W and Ta-Mo systems, associated with room-temperature brittleness for alloys approaching the equiatomic composition, Ta-Nb remained ductile over the complete composition range with little or no solution hardening. Other systems have been investigated by hardness measurements on polycrystalline material and a discussion of the hardening of these alloys has been presented by ~udman." The purpose of the present investigation was to examine the deformation behavior of Nb-Mo alloys in detail, with particular reference to alloy composition and single-crystal orientation. In this way it was hoped to shed some light upon the restricted ductility of these alloy specimens. 1) EXPERIMENTAL PROCEDURE The starting materials were obtained in the form of beam-melted niobium rod and sintered molybdenum rod of suitable dimensions. Since niobium and molybdenum form a complete solid-solution series at all temperatures, alloy single crystals were produced by melting the two constituents together in an electron bombardment furnace (EBM). To produce specimens free from segregation a molten zone was passed over the length of each rod six times in alternate directions at a speed of 10 in. per hr. Typical specimens were analyzed for interstitial impurities by gas analysis and for metallic impurities by spectrographic analysis. The results of this analysis are shown in Table I. Many of the tensile specimens were also analyzed (after testing) by scanning the gage length in an electron beam microanalyzer, from which it was found possible to predict the approximate composition of a specimen from the original proportions of each element in the EBM. The tensile specimens were made with a gage length of 0.5 in. and diameter of 0.075 in., using a Servomet Spark machine. By careful machining on the finest range for the final i hr of this technique, surface cracks could be reduced to the level where they were easily removed by electropolishing in a solution of nitric and hydrofluoric acids. The specimens were strained at a rate of 10 4 sec-&apos; using friction grips designed to prevent accidental straining and maintain a good alignment before straining. The orientations of the individual specimens tested are shown in Fig. 1 and the corresponding compositions listed in Table I1 together with collated experimental data. 2)RESULTS a) General Deformation Behavior. The effect of composition on the room-temperature deformation curves of similarly oriented specimens is shown in Fig. 2. The yield stresses of the pure constituents, while not the lowest reported to date, were at least comparable with existing data. Although the solution hardening was large for alloys at either end of the phase diagram, and comparable with the Ta-W solution-hardening data of Ferris et a1.,8 the low work-hardening rate characteristic of niobium was sustained until a composition of Nb-85 pct MO had been reached. Associated with the peak yield stress ob-

Jan 1, 1969