Search Documents

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By Arthur Knapp

NO oil territory in the world has been so rich in large producing wells, in a comparatively small area, as the Baku field. Particularly is this true of the Bibi Eibat field, which formerly produced millions of "poods " of " gusher," or as it is called in Russia, "fountain" oil. The Bibi Eibat and Balachany fields have been exhausted of gas and ruined by water, but ' the Surachany and Benegadi fields are still fountain territories and: many outlying districts that have only been prospected produce rich fountains. The method of controlling fountains, or gushers, is the result of growth, along with the Russian system of drilling, where large diameters and riveted casing have been in vogue. The screw casing is seldom used except to exclude water. Formerly the method of finishing wells and the condition of the casing at the top of the well would not permit the use of gates, manifolds, and connections as is standard elsewhere. The life of the flowing wells is very short, particularly those 10 in. (25 cm.) or more in diameter, which produce large quantities of sand and often flow for but a few days and are then a complete loss. More than 1,000,000 poods in 24 hr. have been claimed in several instances, but in no case was the flow for more than a few days. The oil sands of this district are free uncemented sands and vary in thickness from paper thin to a maximum of 10 ft. (3 m.). The sands are interlaid with strata of soft clay. In spite of this, the practice has been to drill into such sands and produce from the open hole without screen or liners. Sometimes the casing is set below the oil sand but in this case holes from 21/2 to 3 in. in diameter are drilled opposite the oil sand, which would not have the effect of a screen. Fig. 1 is an outline of the fountain shield ready for the control of a fountain. It is composed of an inner and an outer covering made from rough boards. The framework is made of rough round poles. When a light flow is expected, only the inner lining is built; and when the fountain comes in unexpectedly, it is often possible to build only the outer cover. The bridge is for the purpose of renewing the blocks as they become worn by the flow. The lower block, as here shown, is made of hardwood and is bolted to the crossbeams with brass bolts. The grain end is toward the flow. The upper block, as shown here, is made of cast steel and is also bolted to the crossbeam with brass bolts.

Jan 1, 1921

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By A. T. Beckwith

This paper concerns measurements of low-velocity air currents and investigations on mine ventilation by means of chemical smoke. The chemical smoke used is produced without flame and at ordinary mine temperatures, and therefore presents no ignition hazard in gaseous mines. Mining men who have worked in open-light mines are familiar with the use of tobacco smoke in determining the direction of air travel and approximately measuring low-velocity air currents. The use of chemical smoke is merely a refinement on the use of tobacco smoke and the flameless low-temperature source of chemical smoke has the additional advantage that it can be used in gaseous mines. Ventilation smoke apparatus, Fig I, is a simple device for producing dense white smoke. The apparatus as shown consists of a rubber aspirator bulb which is used to force air through a glass "smoke tube" containing a chemical substance that produces a dense white smoke on contact with air. The apparatus was developed by engineers of the U. S. Bureau of Mines.' It is inexpensive, weighs less than 3 oz, is easily carried in a pocket, and requires no skill to operate. Smoke apparatus is invaluable in practical mine ventilation work for: (I) measuring low-velocity air currents, (2) detecting air leakage, (3) observing airflow characteristics. This paper is written to show the merits of the apparatus, and is based upon findings through its extensive use, during the past six years, in mines operated by the Lehigh Navigation Coal Co. Inc. The Apparatus Certain chemicals, such as stannic chloride (SnCl4) and pyrosulphuric acid (H2S2O7) produce "white smoke" when exposed to air. Stannic chloride gives off vapors which on contact with moist air cause the formation of solid hydrates, of which SnCl4.5H20 is the most important. Pyrosulphuric acid decomposes when exposed to air with the evolution of sulphur trioxide (SO3) fumes, which become white upon contacting moisture in the air. A chemical, such as one of the above, is the active substance in a smoke tube. The glass tubes are hermetically sealed during manufacture, and are made ready for use by merely breaking off the tips at the conveniently located file cuts. When the smoke tube is connected to the aspirator, depressing the aspirator bulb forces air into contact with the chemical, and smoke discharges from the open end of the tube. A white solid (a hydrate if stannic chloride is used, or sulphur trioxide if pyrosulphuric acid is used) may occasionally form a cake in the outlet opening of a smoke tube. A small wire such as an ordinary paper clip can be conveniently employed to dislodge the cake should it seal the tube. When the assembled apparatus is not

Jan 1, 1949

By W. W. Schmittroth, A. Y. Bethune

THE commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc .are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "superpurity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,1 it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon was not desirable. The use of Special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1946

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By W. G. Jeffery, James F. McDivitt

THE FRAMEWORK Consider where you, the reader, would place the emphasis m your answer to the following questions on mineral supply. Do you think of the mineral resources of developing countries in terms of the contribution which they can make to world mineral supply or in terms of the contribution they can make to development of the country? Do you look upon developing countries as a source of minerals for world industry or as a potential enormous market for minerals? If you are from a developed country it would be surprising I£ you did not emphasize the first alternative in each case, but it is also possible that simply raising the questions will call for some mental adjustments, because usually we do not think in these terms. If you are among the two-thirds of the world's population which comes from developing countries, you might well emphasize the second alternative. And to a growing extent during the reaming decades of the 20th century this is where emphasis must be placed. Increasing amounts of the world's mineral production come from countries which are in the early stages of development. Mineral consumers of the world look to these regions for continuing supplies of material to help meet their ever-growing needs; the producing countries look to mineral exports as one means of stimulating and financing their economic development-this seems a happy and fortuitous relationship. But due to the complexities of world mineral supply, it is a relationship which is fraught with potential confusion and misunderstanding. That this is so is not surprising when one considers that many of the producing countries are new countries which are urgently trying to find the path along which they can move towards development; that the direction of the path is by no means clear because various theories of economic development, as a planned and deliberate process, are relatively recent in origin and none are well understood; and that the very concept of the less developed countries (LDC's) is a relatively new one. To further complicate the situation there has never been a clear under- standing of the full role which minerals play in economic development, either in the case of those countries which are already classed as developed, or in the case of countries which are in the process of development. Before embarking on an investigation of some aspects of the relationship between minerals and developing countries, it seems wise to establish broad terms of reference, which may not be totally valid but which will at least give an initial direction for a journey with no clearly definable goal. First it can be noted that the world has been divided somewhat arbitrarily into a group of countries that are termed developed or advanced and a group of countries which

Jan 1, 1976

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

By William P. Blake

THE phenomena of concentric arrangement of minerals in rock-masses, generally known as "orbicular structure," have of late received much attention from investigators. Lawson, of the University of California, has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject. The orbicular diorite of the type locality in Corsica., familiar to mineralogists and petrologists under the name "Napoleonite," was described by Vogelslang in 1862.3 Chrustschoff, of St. Petersburg, has also given much atten¬tion to the subject, and is the author of a classification of the various known forms of orbicular structure.4 No complete and satisfactory explanation of the origin of or¬bicular aggregations in rocks has yet been offered. The patent fact is generally recognized that the constituent minerals have crystallized from a more or less molten or plastic magma, but why these minerals should be arranged in concentric spheres or crusts has not been clearly shown. Vogelslang, for example,

Jul 1, 1905

By D. L., Hayes

THE concentration of zinc ore in Wisconsin is a comparatively simple process, although it presents problems that must be overcome in an efficient manner in such a way that installation and operating costs are low. As the ore deposits are small, the first cost of the concentrating plant must be low; while the low margin of profit makes it necessary to have the minimum operating costs. The original mills were copied from those of the Joplin district, as most of them were built and operated by Joplin millmen. These served the purpose well; they made a clean concentrate, which was the chief requirement at that time, as most 'of the mines were' considerably 'richer than the average at the present time, and wages and supplies were also considerably lower. ' The apparatus used at present has changed very little in principle. . The grizzly opening has gradually been increased to 12 in. and sometimes no grizzly 'is used. The crusher, gradually grew in size, the largest crusher has -an opening of about 24 by 13 in. and a 7/8-in. throw on the. eccentric shaft.

Jan 1, 1921

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926