Search Documents

By J. O. Mack, J. B. Russell

In recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. Table i.—Composition Ranges Prescribed for a Commercial Substitute Solder Element Per Cent Tin............................ 18.0-20.0 Bismuth (maximum)a............ 0. 80 Silver.......................... O. 10-1. 25 Bismuth plus silver (minimum).... 0. 85 Antimony (maximum)............ o. 50 copper (maximum),,,,,,,,..,,,, 0. I3 Other elements, each (maximum)6 0.03 Lead........................... balance a When silver is present in excess of I per cent, the Bi content shall be 0.50 per cent or over. b Total not to exceed 0.10 per cent. The Purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing 18 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic I5-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wet-tability, that will enable it to be used on the metals in common use. Basic Considerations The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat. If a soldering iron is used, it must not only

Jan 1, 1945

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By J. B. Hess, C. S. Barrett

Single crystal rods of cadmium collapse under uniaxial compression into peculiar kinks if the (0001) glide plane is nearly parallel to the axis of compression. In his report first describing this behavior, Orowan1 proposed that these "kink bands" do not develop entirely by ordinary gliding and twinning but by a special mechanism in which glide lamellae of uniform thickness snap abruptly to a tilted position that permits lattice continuity across the glide planes. He concluded that a portion of each boundary of a kink band consists of a plane (non-crystallo-graphic) which bisects the angle between the glide planes on the two sides of it, and along which the bending and the dislocations are concentrated. The data presented by Orowan seemed to us to be insuffcient to conclude that a wholly new mechanism of deformation was responsible for the kinks. Therefore, we have investigated zinc, which is hexagonal close-packed and has an axial ratio near to cadmium, to see whether similar bands are produced, and whether the ordinary mechanisms of glide, bend-gliding, twinning, and the formation of deformation bands can account for its mode of deformation. We find that kinks form profusely in zinc as shown in Fig 1. The structure of these kinks, reported below, seems to require no new mechanism for their explanation, but indicates that kink bands are a special form of deformation bands and develop gradually, solely from basal glide. A theory covering the formation and structure of the bands is presented in detail because it is seldom possible to study deformation bands under such simple conditions, yet many principles applying to these kinks should also apply to deformation bands in general. Experimental Procedures Single crystal rods of 2-3 mm diam and 10-15 cm length were grown by the Brideman technique from swaged wire of Horsehead Special zinc in un-coated pyrex tubes. Orientations of the rods were determined with an optical goniometer after cleaving the rods at liquid air temperature. Crystals of desired orientations were then selected and used as "seeds" to grow additional crystals approximately 4 ft in length from which all specimens were cut. The wires were compressed in two ways: in a simple hydraulic handpress —a "soft" machine—and in a Riehle hydraulic testing machine modified to produce very "stiff" action by the simple expedient of inserting lengths of steel bars at the sides of the zinc crystals between the compression plates. For metallographic examination, the specimens were mounted in sealing wax. Hand polishing was employed, with no grits coarser than No. 1 paper; following the abrasives about 0.025 in. was removed by an etch-polishing reagent.* Final etching to reveal ori-

Jan 1, 1950

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

THE development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. FURNACE LINES About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied between 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: [Hearth diameter 25 ft. o in. Height of bosh 10 ft. o in. Bosh angle 8 1 ½° Diameter top of bosh 28 ft. o in. Inwall batter per foot 15/16 Stock-line diameter 19 ft. 6 in. Large-bell diameter 14 ft. 6 in. Height from iron notch to top ring casting 100 ft. o in.] In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace for the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime, the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1942

By J. A. Jargon, H. K. van Poollen

Flow of slightly compressible fluids through porous media can be described by linear equations. Many mathematical solutions- are available for the boundary conditions of constant terminal pressures or constant flow rates, or a combination of both. Various techniques of formation evaluation use drastic rate changes, such as sudden shut-in. Other methods require that the well be produced at a constant rate. In practice, one is not always able m fulfill these rigid requtirements. This report shows a methor1 by which varying-rate data can be converted to a constant-rate pressure response, called the unit response function. After obtaining the unit response function, one may analyze it, using techniques described in the literature. The method uses tile principle of superposition. Necessary data is a time history of pressure and production. If pressure changes and/or rate changes are very drastic, the unit response function becomes erratic and oscillates The erratic and oscillating results are obvious, and under those circumstances, no answer can he obtained. It appears, however, that a response function without oscilla-tion will not contain any appreciable errors —- one gets either good results or no results. This report includes a mumber of examples of converting constant-rate data to constant terminal-pressure data and vice versa. In addition, a number of field-test applications are given. This method should be useful in converting mathematical solutions from one boundary condition to another. It already has proven useful in converting varying-rate data to constant-rate conditions. INTRODUCTION Pressure drawdown tests are performed on production wells to determine various reservoir characteristics, including permeability, distances to discontinuities, reservoir continuity and wellbore conditions. An ideal drawdown test is performed at a constant production rate with pressure observation during the drawdown period. A typical drawdown curve for a constant rate of production is shown in Fig. 1. In practice, a constant production rate cannot always be maintained. Fig. 2 shows a pressure drawdown curve for a varying rate. Usual methods of analysis are not applicable to tests such as this. It is, therefore, necessary to convert the varying-rate data somehow, before usual analytical techniques can be applied. This report describes a method of obtaining a response function. A response function can be defined as the relationship between pressure and time for a well producing at a constant unit rate. Such a response function can be analyzed by the usual analytical techniques. Hutchinson and Sikora' first approximated a resistance function (response function), and by applying the superposition principle, pressures were calculated using the varying rates. If no match was obtained, adjustments were made to the response function and the closer approximation was used again in an attempt to match calculated and observed pressure behavior. If a good match was obtained: the response function was then used to extrapolate the future aquifer behavior.

Jan 1, 1966

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By M. R. Pickus, I. W. Pickus

Ordinarily age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type. Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a superstructure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,' Jänecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling. Similar changes have been observed in the binary gold-copper systemI6 one alloy of which corresponding to the formula CU³AU, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change. The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on I4-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. Present Investigation As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

By M. R. Pickus, I. W. Pickus

Ordinarily age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type. Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a superstructure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,' Jänecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling. Similar changes have been observed in the binary gold-copper systemI6 one alloy of which corresponding to the formula CU³AU, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change. The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on I4-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. Present Investigation As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

Jan 1, 1883

By E. R. Smith

ANALYSIS of the requirements for gun perforation equipment suitable for penetrating casing and cement showed that these points would be involved: (1) Powder charges electrically detonated under high fluid lieads and at remote distances. (2) Selective firing of sliots in sequence. (3) Sufficient velocity for the bullet to penetrate at least two strings of seamless casing and all cement beyond the strings. (4) Heat-treatment of steels to withstand great pressures and penetration. (5) Esclusiorl of fluid under extremely high hydrostatic pressure. (6) Stranded steel wire line acting as weight - suspending and current - carrying medium. (7) Firing controls operated above the surface. (8) Determining gun depth and suspended weight by means of the wire line. (9) Portability for field use.

Jan 1, 1936

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By Rudolph G. Wuerker

Charles T. Holland (Head, Dept. of Mining Engineeri*, Virginia Polytechnical Inst., Blacksburg, Va.) Mr. Wuerker has presented a very interesting discussion of the use of triaxial test methods for investigating the strength properties of rocks. Such methods, no doubt, eventually will develop considerable information of interest to those concerned with the design of mine layouts, particularly in the field of pillar design. From his discussion of my recent article, "Cause and Occurrence of Coal Mine Bumps" (Holland Mining Engineering 1958, p. 933-1002), it is evident that in one place at least I did not make my meaning clear to him and perhaps others. To clear the matter up I think it best to quote from the article, somewhat more fully than did Mr. Wuerker, as follows: "4) In actual operations — because rocksare not perfectly elastic, homogeneous, nor isotropic and because local yield does occur — the maximum stress as demonstrated by Phillips (Ref. 22, pp. 64, 65) and indicated by much experience in mining, does not occur at the walls of the opening but at a short distance inside the pillar. Furthermore, the maximum stress does not reach as great a value as theoretical considerations and laboratory experimental methods indicate.* Actual distance inside the pillar, measured from the wall, at which the maximum stress exists, has not been determined. Observations in many mines, however, indicate that this distance could have a mini-value of one to six or eight times the bed thickness and that it is probably affected by width and height of the opening, depth of cover, and relative values of the elasticity and plasticity of materials comprising the roof, floor, and coal seam. The actual value of the stress produced probably lies between the theoretical maximum and the average stress concentration that would be produced if the weight of the strata above the unsupported opening were evenly distributed over the pillars for a distance equal to the opening width." The footnote reference in the above quotation referred to the following: "*For example, the Pocahontas No. 4 coal bed in southern West Virginia is mined under cover up to 1800 ft thick. Development openings are driven 18 to 20 ft wide, and the bed is about 6 ft thick. According to the work of Panek, the tangential wall stress at mid-bed height under these conditions would reach values between 4000 and 5000 psi. Actual tests of 3-in. cubes of this coal show its compressive strength would be much less than this, perhaps as low as 400 psi. Yet the pillars usually show no evidence of failure in these headings. In this same bed at a depth of 800 ft, the author has seen an opening 225 ft between supports lying between two old groves approximately 1100 ft apart. According to the theoretical considerations, the stress in the pillar walls would have been about 18,000 psi, yet the pillar showed little or no evidence of weight. In view of these observations, it is clear that the wall stress does not attain the maximum values indicated by theory." (Underlining added to original wording.) By referring to Fig. 2A of my paper it will be noted that theoretically the maximum pillar stress would occur at the pillar wall, i.e., at the passageway surface of the pillar. Obviously this cannot be correct in the cases of stress ranging from 4000 to 18000 psi since the coal at the surface of the pillar is under no constraint and cannot have a strength much greater than 400 or 500 psi. Hence, my conclusion that the maximum stress does not occur at the wall but back in the pillar some distance from the wall. Since these stresses are pushed back in the pillar from the wall, it is also obvious that the loads transferred to the pillar from the opening will be spread over a greater area and hence Pillar stresses will not rise to the values postulated by theory and photoelastic experiment. Further since to visual inspection the coal along the pillar wall did not appear to be failed the conclusion was reached that the stress shift was caused by local elastic or plastic yield and by difference in the elastic modulus of the rocks composing the mine floor, mine roof, and coal bed. Later on under the heading "Strength of Mine Pillars" (pages 1000-1002) the effects of constraint is briefly described. Also a formula taking into account constraint is developed relating pillar strength to the uniaxial strength of coal and the L/T ratio of the pillar. Since my paper was written, reports of experiments conducted in South Africa (Denkhaus, et. al., 1959), in Sweden (Hast 19581, and in Canada (McInnes, et.al., 1959) reveal that the conclusion expressed relative to the existence of a low stress area existing around the edges of pillars and solid faces as described above is generally correct. But it seems possible that where the wall stress developed is less than the unconfined strength of the rock composing the pillar and where the roof, floor, and pillar

Jan 1, 1961

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,'-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970

By Ross E. BROWNE, Ross B. HOFFMANN

IT seems strange that a theory so devoid of value in its application to our practical problems should attract such widespread acclaim. This appears still more remarkable when one considers the foundation on which it is built. The criticism naturally suggested is as follows: First; the special theory of relativity is based on an assumption which is counter to the fundamental conception of relative motion. Second; the theory claims only a slight modification of Newtonian mechanics-a modification so minute that, even if true, it would have no practical value in its application to any visible occurrence here on earth.

Jan 1, 1931

By AIME AIME

No democracy such as ours, can ever be prepared for war, because we could never conceivably be the aggressor. The aggressor prepares in secret, designs his new tactics, and invents and makes new equipment and selects the time to strike. If a democracy prepare done year and the war came later, all that it had one would have to bed one over. All that England has today in the way of effective armament has been invented, designed, made, and the crews trained since the war began, because the totalitarian aggressor introduced new types of equipment and new techniques.

Jan 1, 1941