Search Documents

By H. M. Hobart

This paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the greatest economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of_ Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox, of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per sq. in. (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per sq. in. (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows: Works Carbon Content for Plates 1/4 In. Thick 1 In. Thick A..................... 0.14 0.23 B..................... 0.14 0.25 C2.................. 0.19 0.25 D................. 0.20 0.30 E Upper limit..... 0.35 Lower limit..... 0 24 0.29 Upper limit,.... 0.25 0.30 Lower limit..... 0.21 0.27 Upper limit..... 0.25 0.35 Lower limit..... 0.22 0.28

Jan 1, 1920

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By V. L., McCutchan

FORM of ore bodies, strength of wall rock, and quantity of water that must be handled differ so greatly in the various districts in which the Corporation operates that a variety of mining methods have to be employed. All are underground, however, with the exception of glory holes at Cerro de Pasco from which siliceous silver pacos ore is obtained. In general, the ors is in many relatively small bodies unsuitable for hulk mining, such as caving or top slicing. The strength of the rock and ore rarely permit open stopes, though shrinkage is successfully used on various veins with strong walls, particularly in, Casapalca. Horizontal cut and-fill and square-set stoping with careful filling are the principal methods employed, with the necessarily higher cost for supplies and labor offset as much as possible by care in the avoidance of dilution. The mines at both Morococha and Casapalca are notoriously wet, and even at Cerro de Pasco the quantity of water was enough to retard deep development until the perfection of electric pumps. In Morococha particularly, the extension of successive levels, first from adits of moderate length, then from shafts and heavy pumping installations on the 750 and 1000 levels, and finally by the 30,564-ft. Kingsmill tunnel, was one of the most difficult and long continued fights against water and resulting heavy ground that is recorded in mining history.

Jan 1, 1945

By F. R. Koeberlin

ABOUT thirty miles south of the port of Coquimbo, Chile, nestling in one of the western outliers of the main Andes range, lies the little mining town of Andacollo, a place whose history and traditions make up one of the most romantic pages in the life story of this southern republic. The beginning of Andacollo is shrouded in the penumbra of the pre-Columbian era, but its first mining activity probably dates from about the years 1440 to 1460. It was in the middle of the fifteenth century that the Inca Tupac-Yupanqui, grandfather of Atahualpa, conquered this part of Chile. His domain extended even as far south as the present site of Santiago, and perhaps farther, but was maintained with increasing difficulty against the fiercely independent and indomitable tribes of Araucanian Indians of the South.

Jan 1, 1938

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

By A. B. Kinzel

IT is with sincere appreciation and a deep sense of responsibility that I accept the honor of delivering the Howe Memorial Lecture. In our time metallurgical research has delved into phenomena ever more complex in character, so that much of this work must be done by organized teams. We, of the Union Carbide and Carbon Research Laboratories and the Electro Metallurgical Co., are truly a team and the lecture which is to follow is due largely to a few of the outstanding members of that team here cited and well known to you in their own right: John Lamont, whose work deserves special recognition, Walter Crafts, William Forgeng, William Binder, Robert Fowler, and David Swan. Thus it is a fitting pleasure to accept this honor for the research institution which I represent. Henry Marion Howe was truly inspirational and his breadth of view was such that he could use either the method of rigid proof or implied mechanism to further the broad understanding. But perhaps his outstanding characteristic was his sound judgment and his ability to weigh observations. The following is replete with observations and judgment as to their implication. We would like to feel that it is the type of dissertation which Howe, himself, would have enjoyed. Chromium carbides in stainless steel have, in a sense, been a key to the progress of the stainless steel industry. Brearley's first stainless steel, containing approximately 0.30 pct C, was successful because it differed from previous Fe-Cr alloys in that the carbides were present in such amount and form as to provide the stainless and cutting properties. Again, the 12 pct Cr die steels with a carbon content of 1.5 pct or more achieved their properties by virtue of the form and distribution of the chromium carbides. In the straight chromium steels with from 12 to 25 pct Cr, chromium carbide amount and distribution are once more the determinants with respect to physical properties and corrosion resistance. In each of the cases just cited the role of the carbide is in essence similar to that of iron carbide in carbon steel and this story is so well known that we need not dwell on it. In the austenitic stainless steels, the chromium carbide plays only a minor positive role with respect to mechanical properties, and for corrosion resistance the objective is to achieve maximum homogeneity. Thus the tendency has been to ever lower the carbon and correlatively the chromium carbide content of the austenitic steels. Today stainless steels with carbon less than 0.03 pct are beginning to find their true place, and this is being aided in major degree by our Company's introduction of a new type of ferrochromium having negligible carbon. The role of carbon in these austenitic steels has long been recognized, and a truly enormous amount of research has been devoted to the subject. Much has been learned about corrosion resistance, but the attack on the problem from the point of view of carbide precipitation and the nature thereof has left much to be understood. Because of its fundamental importance to the future of stainless steels, further study of the mechanism of carbide formation in austenitic steels is of interest. In the 18-8 Cr-Ni steels, which are typical of the austenitic class of steel, carbon is soluble in the aus-tenite to the extent of approximately 0.15 pct at 1832°F (1000°C). The solubility becomes less with decreasing temperature, so that at 1652°F (900°C) the solubility limit is approximately 0.06 pct, at 1472°F (800°C) it is about 0.03 pct, and at 932°F (500°C) it is approximately 0.01 pct. Obviously this is the ideal situation for the classical precipitation phenomenon. It is true that, in a sense, 18-8 austenite resulting from annealing is in a metastable state, and the phenomenon of ferritic precipitation from this austenite should be considered. However, in a so-called fully austenitic 18-8 steel this is secondary with respect to the carbides and can be neglected. A wide variety of chromium carbides is known. Only one chromium carbide, Cr,,C,,, frequently referred to as Cr,C, has been found in unmodified low carbon 18-8 steel. This, fortunately, simplifies the study of the precipitation phenomena. For this study an A.I.S.I. type 304 stainless steel of commercial quality was selected. Analysis showed C 0.07 pct, Mn 0.49 pct, Si 0.33 pct, Ni 9.34 pct, Cr 18.91 pct, and N 0.033 pct. As expected with this composition the steel was homogeneous after annealing except for a few pools of ferrite, which were disregarded in that their location was not coincident with subsequent carbide precipitation areas. On corrosion testing the steel was normal and typical of good commercial quality. Specimens 1/2xlx4 in. were annealed and subjected to precipitation heat treatment for 100 hr at 100" temperature intervals from 1000° to 1500°F and for ten selected intervals ranging from 5 min to 64 hr at 1300°F. These blocks were then cut into small pieces for metallographic studies. The first problem

Jan 1, 1953

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By A. B. Parsons

LECTURE, it appears, is a discourse that is supposed to be instructive. I am quite sure that you will derive no instruction from what I have to say. I will be satisfied if my remarks provoke thought along one or two mental paths that have not been traveled so fre¬quently as to be devoid of interest. I have no particular message apropos of professional engineers or professional engineering, and any conclusions that I may seem to reach will be purely tentative and incidental. Probably at times you have wondered, in a casual way at least, why so many people who are not, never have been, and never will be engineers, want to use the title. For example, I recently received a communication from a life insurance broker or salesman, whose chaste letterhead bore the legend "Estate Engineer." He was perfectly serious about it, as is also the expert accountant who assumes the imposing name of cost-analysis engineer. Dozens of equally amazing titles might be cited. Then there is that class of individuals who have been engineers, in the true sense of the word; who have gone into some other kind of occupation; but who cling tenaciously to the name engineer, usually prefixing some word or other which at once gives them away by telling what their work really is. For example, we have such pseudomorphs as the management engineer, and the sales engineer. It is quite evident that engineer is a word to conjure with. Evidently both the man who appro¬priates the designation without any justification and the ex-engineer who persists in calling himself an engineer even after he has abandoned engineer-

Jan 1, 1933

By Bradley Stoughton

A LL over our great country I have been privileged to see, during the last six weeks, the manifestation of a new spirit among engineers. Partly under the inspiration of leaders whose influence has been felt not only nationally, but internationally, - partly through the recognition of the service that engineers have been able to render to the nation during the recent crisis, a new self-consciousness has been acquired by the individuals, and now this self-consciousness seeks expression in opportunities for service and participation in public affairs. The engineer . no longer sees himself a mere reservoir of information to be tapped when some one is in need of cold facts, no. more an administrator of mere material things, but a potential administrator of- public affairs, a citizen and a human being, with the responsibilities, as well as the privileges of citizenship.

Jan 1, 1920

By S. A. Swensrud

NINETEEN Thirty-Six was the biggest year in volume in the history of the oil industry, and unquestionably the best since 1929 in respect to profits. The quota of new and difficult problems to face seemed a little smaller during 1936 than in most recent years, and a somewhat better balance existed between the different branches of the industry. 'Domestic consumption of gasoline in 1936, estimated at about 475 million barrels-the highest on record, was approximately 11 per cent above 1935, and 26 per cent above 1929. Demand for crude oil increased in about the same proportion: over 1935, and the average production, of about three million barrels daily,' constituted a new high level.

Jan 1, 1937

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority's resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944

By AIME AIME

DOUBT in anyone's mind that this is the age of metals, industrially speaking, could easily have been dispelled by attending the National Metal Congress in Chicago, Sept. 22 to 26. Iron, copper and aluminum; zinc, lead and nickel, often alloyed with each other or with some of a dozen minor metals, make the materials without which the modern world could not run. Science, pure and applied, is doing marvels in finding new mixtures, new alloys to meet new needs; in developing new means of rolling, fabricating, casting and welding metals cheaply-and effectively. These and related matters were the subject of 100 papers presented at 33 seperate sessions of the organizations that participated in the congress.

Jan 1, 1930

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By Theron Wasson

Michigan's production of 17,301,000 bbl. in 1945, which is in line with previous years, has been maintained by extensions to old fields like Deep River, Adams, Fork, and others. There were a number of new discoveries but, as in the past, these are not given very much importance because enough drilling has not been done to develop their potentialities; however, judging by the past, some of them will develop enough production so that 1946 -will probably be in line with other years. Activities in Michigan were confined to the Basin area of the lower Peninsula, which has been under development since 1925.

Jan 1, 1946

By N. A. Zeigler

GRaphitization phenomena occurring in solid cast iron have principally been studied from the angle of the reactions taking place during annealing of white castings in the manufacturing of malleable iron. The selected bibliography at the end of this paper presents the high spots of the published information in this field. Graph-itization of gray iron upon reheating has received much less attention, primarily because only on rare occasions is this material subjected to any kind of industrial heat-treating. Moreovcr, articles made from gray iron are seldom used commercially at temperatures when any graphitization can take place. When used in such conditions, it is assumed that the articles can be replaced at frequent intervals, which can be afforded because of the low cost of gray iron. However, there is at least one commercial process in which articles made from gray iron, during their manufacturing processing, are subjectcd to rather high temperatures; that is, manufacturing of cast-iron enamelware, which is glazed at about 1600° to 1700°F. (870' to 930°C.) From practical experience, it has been found that one of the convenient and economical compositions of gray iron suitable for enameling is, in round figures, as follows: Si, 2.50 per cent; Mn, 0.35; S, 0.07; P, 0.80; T.C., 3.35; C.C., 0.70. Since this iron usually is cast into thin-walled sections, the percentage of com- bined carbon in it is relatively high. Upon heating in the enameling furnaces, this combined carbon graphitizes, which causes permanent dimensional changes of the articles. Obviously, from practical considerations, it is desirable to maintain these dimensional changes as constant as possible. In the course of experimentation with this iron, two series of experimental heats were prepared in which the manganese to sulphur ratio of the standard cupola metal was offset by ladle additions of: (I) progressively larger amounts of sulphur, and (2) progressively larger amounts of manganese. Each one of these ladle charges was cast into experimental plates 8 by 4 in. and about 5/16 in. thick. All told, 13 ladle charges were thus treated. All of them are listed in Table I, together with their chemical analyses. It may be noted that the manganese to sulphur ratio in these samples ranges between 1.2 and 30.2. Every one of these compositions was subjected to thermal allalysis, using an automatic, self-recording differential dila-tometer. The specimens used in this instrument are 50 mm. long and 4 mm. in diameter. During the dilatometer cycle they are kept under a vacuum of about 3 microns. Each one of them was subjected to a thermal cycle by heating it to I830°F. (1000°C.) in 3 hr. and cooling to room temperaturc in 5 hr. Figs. I, 2 and 3 present three automatically recorded dilatometer curves for irons: Serial No. I (normal composition), Serial No. 6 (high sulphur), and Serial No. 13 (high manganese). All three of these figures are

Jan 1, 1945

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949