Search Documents

This report provides concepts for two automated longwall mining systems; one for operation in a 42 to 57-inch thick section of the Lower Kittanning coal seam, the other in a 57 to 72-inch thick section of the Pittsburgh seam. The Lower Kittanning concept uses a single-drum bidirectional shearer and 500-ton capacity 4-leg chocks and the Pittsburgh concept uses a double-drum shearer with 500-ton shields. Each concept is designed to produce in excess of 2,500 tons of clean coal per shift with a 6-man face crew. The automated longwalls consist of off-the-shelf control system hardware attached to standard longwall equipment. Control hardware includes a control and display console; prime and backup mini-computers; multiplex data transmission, power, and control lines; several remote terminals which serve as interface junctions; and various sensors and actuators located on the longwall equipment. The system can be operated either fully automatically, remotely or manually.

Jan 1, 1976

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By William L. Young

There is an old saying in Canada: "Mines are made as much as discovered." What follows is Young's perception of his experience developing and financing the Cochrane Hill gold mine project. In 1974, I came back from rutile and zircon exploration and mining in Australia. I became interested in a copper, lead, and zinc project in the Bathurst District, New Brunswick. Much field work had already been done but I was convinced that a reinterpretation of the geophysical work left room to enlarge on the known mineralization. So, with my own money I put a property deal together, found an underwriter willing to raise $100,000, and had a lawyer produce a prospectus. The prospectus was ultimately accepted for filing by the Ontario Securities Commission and I acquired funding and began work. It did not take many drill holes to determine that the interpretation was not geologically valid. However, while drilling was going on, geophysical and geochemical explorations indicated interesting anomalous zones elsewhere on the property. But by now the base metal market climate had soured and the $50,000 I had left was not enough to evaluate the new results. So I decided to farm out the property. A data folio was produced and the property was optioned to a major mining company, with Northumberland Mines Ltd. retaining a 20% free, carried interest. By 1976, the market for junior issues was so bad no under¬writer would even talk to a geologist and I still had the $50,000 in the bank and was looking for something to initiate. A Project That Went Nowhere Market research indicated that the Toronto area imported fine calcium carbonate fillers from Georgia, Alabama, and Vermont. I was aware of the specs and the fact that there is a large marble belt in Eastern Ontario. After some prospecting, I found an interesting deposit. The product was slightly high in silica and low on brightness. Research work eliminated the silica and corrected the brightness. So, with insufficient money we launched a feasibility study. This included diamond drilling, bulk sampling, special fine grinding and air classification tests, and an in-depth market survey. Our product was as good or better than those on the market. Our advantage was that delivery could be made by a two-hour truck haul to the customer. The present system of rail delivery had many problems, especially in winter. Despite everything looking rosy, we ran into a stone wall. The underwriters were singularly unimpressed because the public saw little glamour in a substance most people had never heard of. The issue would have been difficult-if not impossible-to sell. Banks and government agencies took the position that if we could get long term take-or-pay contracts then they would lend the required capital. None of the suppliers, however, would even consider a contract until production had begun and they could evaluate the production material. It was a classic "catch 22" situation. I have gone into this in some detail to show how tough the industrial mineral market can be. We eventually optioned this calcium carbonate property to a major corporation. The option agreement would give us a free, carried 15% and the right to buy up to 40% for contributing 25% of the production costs. But the experience left my company in poor financial shape. To survive, I think the entrepreneur-geologist must always have at least one project in reserve, an emergency plan. I had been searching out a new project to work on, after the calcium carbonate option was wrapped up. It was gold. Gold intrigued me and I knew quite a bit about Nova Scotian gold. I felt that with any rise in price, many of the former high-grade gold mines would have interesting potential for the larger, low grade portions of the deposits. That is how I happened on Cochrane Hill, where much work had been done in the early 1970s when gold as $4.82/g ($150/ oz). This time my timing was good. No sooner had Northumberland signed an option agreement than gold prices started to rise. In six months, they went to $27.331g ($850/oz). Even so, financing gold prospects in early 1980 was still not easy. It had been years since gold financing had been undertaken. A whole new generation of investors, with no knowledge of gold mining, had grown up. So, with accounting and legal council, we decided on a semiprivate "seed money" offering. Under the new Ontario Securities Act, this was a new-and partly tax sheltered-concept. At the time, it was very innovative.

Jan 6, 1982

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

By Donald Mc Laughlin

El presente texto revisa los antecedentes y la capacidad metalúrgica para la instalación de una planta de fundición. Para ello, se revisa la fuerza metalúrgica, coke metalúrgico, inversiones, mano, capital de trabajo, producción y rendimientos, balance económico, efectos de las fluctuaciones de precios en el balance, económico financiación, fertilizantes y ventajas de la central metalúrgica.

Jan 1, 1959

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007

By Julio Villon

Actualmente en las técnicas de trabajo de minería es frecuente el uso de tecnologías como la teleoperación, telecomunicación, capacidad computacional masiva, redes de información, bases de datos más poderosas, etc. Por ello, es necesario considerar que el éxito en la implementación está relacionado al proceso de adopción, los requerimientos de capacitación y el manejo del cambio. En ese sentido, el presente texto señala la importancia de la integración tecnológica en la minería para mejorar la productividad y la gestión de los activos. La actividad minera debe ser enfocada como una cadena de valor que tiene diferentes procesos alineados con la estrategia y los objetivos de la empresa. Dichas definiciones van a reflejar la manera cómo la empresa decide relacionarse con su entorno: accionistas, clientes, proveedores, trabajadores, estado, comunidad. Los procesos se traducen a nivel de secuencias de actividades y de ejecución de estas definiciones.

Sep 19, 2006

By Eder Salazar

El presente texto describe la optimización de la productividad en la empresa minera a través de la mejora contínua en la cadena de valor en SMEBSAA, los siete pasos de la calidad, proceso de mina, planta, soporte y la cuantiificación de dicha mejora en la cadena de valor en SMEBSAA. Asimismo, la implementación de los diversos sistemas de gestión refuerzan los resultados, siendo el Sistema de costeo basado en actividades el gran agrupador de toda la información de los módulos: Logístico, Control Patrimonial, Orden de Servicio, Planillas y Contabilidad.

Sep 12, 2005

By Fábio Rogério do Carmo

O ar soprado é uma das principais utilidades responsáveis pelo processo de transformação do minério de ferro em gusa no Auto Forno. Para que ocorra o processo de redução o ar soprado é superaquecido nos regeneradores dos autos fornos a uma temperatura de 1.300°C. Este energético é fornecido na CSN-UPV pelos turbos sopradores da Central Termoelétrica nº 2 (CTE#2), área dos Motos Sopradores 1 e 2 e os turbos sopradores n°1 e 3 da CTE#1 que operam com a velocidade reduzida 24 horas soprando para atmosfera e consumindo vapor de 30Bar. Devido à obsolescência do sistema de ar soprado da CTE#1, alto custo de operação e risco para a segurança operacional, este trabalho apresenta o estudo do problema em questão, a metodologia utilizada para desativação do ar soprado da CTE-1 e a redução de custo.

Sep 25, 2017

By Alfonso Ballón

La producción de hierro por medio del alto horno se realiza en condiciones limitadas en lo que refiere al combustible reductor coque, ya que necesita mayores proporciones de materias volátiles en los carbones originarios. Por ello, la presente investigación remarca la importancia del uso del horno eléctrico de reducción o de cuba baja, como unidad metalúrgica más idónea para producir arrabio de variadas cualidades. Asimismo la aplicación de este horno, permite extender su producción en la industria siderúrgica de algunos paises europeos y asiáticos, y por qué no dentro de América Latina.

Jun 20, 1954

By J. M. Elder, W. S. Kow

Challenges to new heavy mineral deposit developments are presented. These include land use issues, particle fineness, declining grades, and particle coating, amongst others. Industry responses to these are presented as possible solutions.

Jan 1, 2005

By K Ringwood, J Cummings, C J. Moran

The development of a water accounting framework that enables consistent and contextual reporting of minerals operationsÆ water use, represents a key sustainable development objective that many Australian minerals companies have committed to. A future water accounting framework will require: key terms and definitions for water metrics for use in the Australian minerals industry that are consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current regulatory requirements and voluntary approaches were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (eg water loss through evaporation). The adopted terms and definitions typically require a combination of empirical and estimated data. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites, selected to test a variety of commodity and biophysical situations. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and following a period of stakeholder engagement and third party review, is being refined as a first step towards developing nationally consistent water use reporting for the Australian minerals industry.

Jan 1, 2009

By José Arango

La Planta Hidrometalúrgica de Cerro Verde tiene como objetivo alcanzar la máxima calidad en cada uno de sus procesos operativos. Para ello, desarrolla un diseño que permita la transformación del control remoto a una operación automática, generando decisiones lógicas. En ese sentido, el presente texto señala la importancia de los Sistemas de información de operaciones en el sistema de automatización de Cerro Verde - en tanto es soporte de la implementación de un completo sistema de instrumentación y de la instalación de una red de PLC’s que colectan la información y en base a esta, desarrollan una lógica de operación manteniendo interconectados todos los circuitos operativos. Posteriormente, con el uso de software se crea una interfase de conexión entre la red industrial y la red Administrativa, permitiendo adjuntar la información en una base de datos que junto a la otra base administrativa, constituyen un ERP que da vitalidad a nuestra operación. De forma que los sistemas de informacion instalados en Cerro Verde consideran a los sistemas de instrumentación como los ojos del operador de planta.

Jul 17, 2000

By Edgar Carlos García Flores

El presente texto señala al Perú como modelo de sistemas de explotación minera para Bolivia -en tanto desarrolle, prepare y explote las minas con calidad y así incrementar la producción de sus operaciones mineras. Asimismo, describe los procedimientos idóneos para seleccionar las tablas geomecánicas, la ingeniería de explosivos, equipos de acarreo y los elementos de sostenimiento adecuados para las excavaciones subterráneas con el objetivo de tener operaciones de calidad, seguras y óptimas.

Feb 1, 2015

By Harold M. Wrigth

El siguiente estudio refiere al diseño y costo de construcción de las plantas concentradoras, así como el de plantas de beneficio realizadas en la provincia de British, Columbia. Para ello, el autor, quien diseñó aproximadamente 16 plantas para el tratamiento de minerales en el mencionado lugar, propone la dfusión y aplicación de este tipo de máquinas en nuestro país, considerando los tonelajes, las ubicaciones, resistencia del terreno, el flow sheet, para sentar las bases del diseño de los equipos.

Jun 20, 1954

By Edgardo Rabanal, Mario Adrianzén

El presente trabajo nos permitirá demostrar las bondades del potencial que tiene el enfoque de Newmont para la gestión de riesgos integral que es el Sistema de Gestión de Riesgos (RMS Risk Management Sistem) uno de los principales componentes es la Gestión de Riesgos de Fatalidad (FRM, por sus siglas en inglés de Fatal Risk Management) que es una herramienta primordial de gestión para evitar fatalidades. En los proyectos de Newmont Yanacocha (Proyecto Yanacocha Sulfuros YSP y Proyecto de Tratamiento de Aguas WTP2) se utiliza el FRM para brindar asesoramiento, acompañamiento y empoderamiento en la salud y seguridad de las empresas locales y sus colaboradores.

Sep 29, 2023

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978