Search Documents

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By Anderson Ayres Bittencourt

O monitoramento de sistemas e ativos de automação sempre existiu de forma rudimentar e descentralizada. A análise desses dados tanto quanto sua obtenção é um desafio para as empresas atuais. Foi a partir deste princípio que nosso projeto foi desenvolvido.Este trabalho tem como objetivo demonstrar a solução de Monitoramento online e preditivo implementada na ArcelorMittal Aços Planos da América do Sul, onde desde o início de sua implementação pudemos capturar benefícios operacionais, melhoria dos processos, otimização, eliminação e/ou diminuição de indisponibilidade de plantas, entre diversos outros retornos que serão apresentados.

Oct 30, 2017

By M. Ounpuu

"Gold, because of low head grade and recovery, is usually of minor importance in the economics of base metal flotation mills. Because of the above little metallurgical attention is usually provided to gold in these mills. But collectively, the gold losses can be significant. For instance, Noranda presently has interest in 13 base metal flotation mills with a collective gold recovery of only 50%. Gold losses are in the order of 150.000 oz per year!The Noranda Technology Centre, in cooperation with Noranda's milling operations, has been investigating the potential of gravity concentration of gold from base metal flotation mills. This paper outlines the pilot and plant testing conducted at three operations with distinctly different ore types; porphyry copper, complex massive sulphide and polymetallic semi-massive sulphide. Testing has been with the Knelson Concentrator which has proven to successfully recover fine gold in a simple, trouble free circuit. Discussion of issues which have risen from the testwork is included. INTRODUCTIONGold, because of low head grade and recovery, is usually of minor importance in the economics of poly-metallic base metal ores. TABLE I presents gold heads and recovery for some of Noranda's base metal mills. It should be noted that the stated recoveries are to payable concentrates, but does not reflect the actual payable gold recovery which in cases is significantly lower. Noranda's average gold recovery into a gold payable concentrates is about 45%. This equates to a collective loss in the order of $57 MM per year of gold"

Jan 1, 1992

By Ariel Medina, Alvaro Rendón, César Moscoso

El presente trabajo tiene como finalidad explicar la importancia de adoptar un enfoque híbrido en los modelos clásicos de molienda, abriendo paso a nuevos modelos híbridos que habilitan la determinación de información clave para la optimización del proceso y de la forma más oportuna posible: en tiempo real. Luego, se expone la metodología utilizada para el desarrollo y validación de un modelo híbrido particular capaz de predecir en tiempo real, con alta efectividad y precisión el nivel de llenado de bolas (Jb), nivel de llenado total (Jc) y potencia consumida de un Molino SAG en operación.

Sep 30, 2022

By Rob Barber

This paper shares the experience of the Alberta Energy and Utilities Board (EUB) Field Surveillance Branch over the past few years in building relationships with Aboriginal communities. Our goal is to provide and encourage best practices that may benefit you and your organization and result in strong, mutually beneficial relationships with a focus on Aboriginal communities. Historical information provides insight that aids in establishing effective working relationships with Aboriginal communities. An important component is appreciation of the perspective of these communities, which is achieved through awareness training. The use of local Aboriginal resource people as part of the training is recommended. A plan that is supported by management and staff is essential and lays the foundation for successful relationships. However, the plan must be flexible enough to change as circumstances warrant. The concept of having local people in communities address local issues is essential. This ?grass roots? approach, combined with the goal of exceeding a community?s expectations with respect to addressing issues, will go a long way to establish trust and credibility. Measuring the effectiveness of this work is the final building block to complete the picture.

May 1, 2004

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By A. de Meyer

Zincor experienced significant losses of metallic zinc to dross during the melting of zinc cathode plates. In this study five factors affecting the formation of dross are identified from literature. Dross from both the plant and that produced in the laboratory is characterized using XRD. An empirical model, based on laboratory-scale investigations, was developed to quantify the effect these factors on their own or in combination with each other has on the amount of zinc loss to dross. The predictive capability of the model is evaluated based on the laboratory-scale investigations. Predictions are made on the effects that heat treating the cathode plates prior to melting, increasing the cathode plate thickness, washing and drying prior to melting, and loading the furnace in a controlled manner have on the amount of zinc loss to dross. Keywords: Zinc, dross, optimize, smelter, yield, losses, empirical, model, XRD.

Jan 1, 2010

Hydrogen and carbon monoxide reduction data were obtained on pelletized materials of the type currently being prepared commercially in Australia.Pellets, approximately 1 cm diameter, made from Deepdale, Iron Prince, and Mt. Newman iron ore were reduced by hydrogen over the temperature range 500°-900°C and the reduced pellets were examined by thermogravimetric, microscopic, electron probe, and x-ray techniques. After an initial time delay it was found that up to 95 per cent reduction the data could be described by a porous model where gaseous diffusion through the solid is rate controlling. Independent measurements of effective diffusivity supported the values obtained from the reduction data. Above 95 per cent reduction the rate decreased markedly due to the formation of retained wustite or fayalite.Comparison with reduction by carbon monoxide over the temperature range 750°-900°C showed that the rate of reduction was approximately five times slower than for reduction by hydrogen.The rate of reduction was found to be a function of the initial properties of the pellets which may account for the widely conflicting results that have been obtained with previous investigations on porous pellets.

Jan 1, 1971

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 4 and 5, 2005. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. Important topics discussed among the attendees included the price of copper, community relations and education.

Jan 1, 2006

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

Biosorption of Cr(VI), Pb(II) and Zn(II) from Aqueous Solutions by Immobilised Phanerochaete chrysosporium Biomass in a Fixed-Bed Column The continuous-flow adsorption of Cr(VI), Pb(II) and Zn(II) from aqueous solution by immobilised Phanerochaete chrysosporium biomass in a fixed-bed column was studied. The effects of flow rate, influent concentration of Cr(VI), Pb(II) and Zn(II) and bed depth on breakthrough curves and biosorption capacity were investigated. The experimental results showed that the breakthrough time decreased with increasing flow rate, increasing influent concentration and decreasing bed depth. The data also indicated that the equilibrium uptake of Cr(VI), Pb(II) and Zn(II) increased with decreasing flow rate and increasing influent concentration of Cr(VI), Pb(II) and Zn(II). Two models were employed to predict the breakthrough curves and to determine the characteristic parameters of the column useful for column design. The Thomas model was able to predict the breakthrough curve in the range of relative concentration(Co/Ci) higher than0.3, Cr(VI), Pb(II) and Zn(II) whereas the validity of the Bohart-Admas model was limited to the initial part of breakthrough curve at all flow rates and influent concentrations of Cr(VI), Pb(II) and Zn(II). The feasibility of reusing the immobilised fungal beads through five adsorption/desorption cycles in fixed-bed column was investigated.

Sep 13, 2010

By Carlo Vargas Bolívar

Dado que en el 2003, se publicó la primera serie de estándares para la aplicación y certificación del Código Internacional para manejo del cianuro, se incrementó el número de compañías qe buscan certificarse con este estándar. En ese sentido, el presente texto describe el proceso para la certificación de este Código del Cianuro, evolución, ventajas y marco legal. El objetivo del Código es mejorar el manejo del cianuro utilizado en la minería del oro y ayudar en la protección de la salud humana y reducción de impactos ambientales. El programa se centra exclusivamente en el manejo seguro del cianuro, relaves de molienda de cianidación y soluciones de lixiviación.

Sep 1, 2014

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By Jim Peterson

Raising equipment that is commonly used include handheld drills such as Jacklegs or Stopers, Alimak raise climber also using handheld drills, drop raises using long-hole drills whether top hammer or ITH drill systems, Raise Bore machines and gang hammers or cluster drills such as the V-30 MRI attachment tool. Sometimes as a community we forget successful techniques used in the past and need to rediscover them.

Jan 1, 2014

The Kalgoorlie Tailings Retreatment Project (or "Kaltails") involves the reclamation and retreatment of approximately 50 million tonnes of gold tailing situated on the Golden Mile at Kalgoorlie, Western Australia. Tailing is reclaimed and retreated at the rate of 42 million tonnes per annum. The project is a Joint Venture between Poseidon Limited and Gold Corporation, with Poseidon being the major participant (90%) and manager of the operation through its wholly owned subsidiary Kaltails Mining Services Pty Ltd. The marginal nature of the tailing retreatment project dictated that a detailed feasibility study be undertaken. Extensive sampling and metallurgical testing of the tailing permitted the development of an optimum economic processing route. A sensitivity analysis undertaken as part of the feasibility study indicated the project to be very sensitive to gold price and unit operating cost variations, and relatively insensitive to capital cost variations.

Jan 1, 1990