Search Documents

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Daudi R. Waryoba

Keywords: Wire Drawing, OFHC Copper, Recrystallization, Orientation imaging Microscopy (OIM), Texture inhomogeneity Textural inhomogeneities have been investigated in oxygen free high conducting (OFHC) copper wire drawn at room temperature to a true strain of 2.31, and isothermally annealed at 250°C and 750°C for annealing times ranging from 10 s to 1 hr. Local orientations were mapped by means of orientation imaging microscopy (OIM). The microtexture of the drawn wires showed a strong <111> + weak <100> duplex fiber texture at the inner core, whereas the mid and surface regions had a comparatively weak texture. Annealing at 250°C resulted into a recrystallization which originated from the mid section, proceed towards the surface regions and ends in the inner core. Recrystallization resulted into a strong<100>+weak<111> duplex fiber texture. A similar textural inhomogeneity was observed during short annealing at 750°C. However, prolonged annealing gave rise to abnormal grain-growth that proceed from the inner core to the outer surfaces with a dominant <111> fiber component at the inner region and mixed components of <111>, <100>, and <112> at the outer surfaces.

Jan 1, 2005

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Helga Larravide

A new on-line database of literature about copper has been created through a joint undertaking by the Copper Development Association Inc. and PROCOBRE-Chile, with funding provided in part through the International Copper Association, Ltd. The new database will permit Spanish-speaking technologists to access publications maintained by PROCOBRE-Chile by means of standard keyword searches. In addition, a new Spanish- English thesaurus has been written to enable Spanish-speaking individuals to search d access the Technology and Environmental databases of the Copper Data Center, which together comprise more than 80,000 publications dealing with the production, properties, uses and environmental effects of copper. Planned expansion of the new Spanish literature database is described.

Jan 1, 1999

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Thomas Prietl

The use of gas stirring systems through the furnace bottom is common for anode and holding furnaces in the copper industry The first implementation of a gas stirring COP KIN® system in a Peirce-Smith converter was performed at the New Boliden smelter, Rönnskar, Sweden. In addition to other benefits, a decrease in process time and a decrease of the oxygen content in the blister copper were observed. To determine the effects of the gas stirring system and the process endpoint, an optical production control ?Semtech OPC system? was used. The light emission of the converter flame as an optical process parameter provides qualitative on-line process information, and is also used for endpoint determination of the slag making process, on-line control of iron content in white metal, quality control of slag etc. The results, benefits and risks of using the COP KIN® and OPC system for a Peirce-Smith converter are reported.

Jan 1, 2005

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By Heikki Jalkanen

The mineralogical composition and morphology of solidified copper smelting and converting slags are of some interest from slag cleaning (by froth flotation), impurity elimination, and environmental points of view. Properties result from both the state of molten slag before solidification and processes taking place during solidification and cooling. In solidification and cooling, copper and sulfur dissolved in molten slag are .precipitating substantially from the silicate phase. Even in water quenching of slag, dissolved copper is pushed out of the solution in the form of finely divided precipitate. Elements present in the raw materials are distributed in a distinct manner between the solidified slag and non-silicate solidification products. Arsenic, antimony, and tin are strongly accumulated in copper precipitate, but not the other metallic constituents common in copper concentrates. Smelting and converting slags differ remarkably on their mineralogical composition and morphology although resulting principally of same chemical processes. Converter slags are more inhomogenous; they often contain solid particles and copper content is .as a rule higher than in matte smelting slags. The final copper content of converter slags was observed to be in a distinct manner dependent on iron oxide - silica ratio. Slag forming, solidification, and precipitation phenomena are discussed on the basis of mineralogical and morphology analysis of smelter slags and laboratory scale experiments.

Jan 1, 2002

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By P. A. Olubambi1

Representative samples of the hydrothermal vein deposits of the bulk complex sulphide ore deposit, 10 km south of Ishiagu, in Ebonyin State, South Eastern part of Nigeria were collected from two small scale mining companies. The samples were mixed and successively crushed in a jaw crusher and cone crusher, and ground in a rod mill. Characterization was carried out with SEM, EDX, XRD, XRF and ICP-OES. Mineralogical analysis revealed the presence of sphalerite, galena, siderite, pyrite, quartz and chalcopyrite. X-ray Diffractometry showed that sphalerite mineral in the ore occurs as sphalerite ferrous with varied percentage of Zn and Fe within the various sizes while chalcopyrite occurs as a chalcopyrite group mineral with chemical formula Cu2MnSnS4. Results of the elemental analysis showed variations in elemental composition within the different sizes.

Jan 1, 2006

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By Zhang Chuanfu

Keywords: solid solution, Ni-Co alloy powders, thermal decomposition, fibres. Synthesis of fibrous Ni-Co alloy powders was achieved by thermal decomposition of precursor of complex Ni-Co oxalates solid solutions obtained via modified coprecipitation method among intimate mixing solution of NiCl2?6H2O , CoCl2?6H2O and H2C2O4?2H2O in the presence of surfactant polyvinylpyrrolidone (PVP) and organic solvent ethanol. Scan electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), disperse energy X-ray analyses (EDX) were used to characterize the structure features and chemical compositions of the as-prepared fibres. The influences of decomposition conditions, including temperature, time, the flow rate of N2+H2, and the heating rate, on the morphology, average size and specific surface area of the Ni-Co alloy powders were investigated. It is found that a trend of the mutual alloying of nickel and cobalt: the formation of perfect solid solution for any compositions NixCo100-x was indicated and corresponding NixCo100-x alloys with fcc phase can be obtained under the optimal conditions.

Jan 1, 2005