Search Documents

By Steve P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39 instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6 m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor varia¬tions in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

Jan 1, 2001

By Leo Gilbride

Western U.S. longwall operators face increasing challenges with optimizing ground control and productivity as mines reach greater depths and coal bursting hazards increase. Some western U.S. mines, many known to be bump-prone, achieved a successful balance between ground control and productivity by transitioning to side-by-side longwall panel mining combined with a yield pillar gateroad system. With this design, development footages could be minimized and pillar bumping averted by controlled yielding at moderate depths, generally in the range of 450 to 600 m. Over the past four decades, the yield pillar system has won wide acceptance among western mines facing pillar bursting hazards, particularly those in the Wasatch Plateau and Book Cliff coal fields of central Utah. However, recent attempts among the deepest Utah operators to mine side¬by-side panels with yield pillars at depths in excess of 600 m have been met with mixed success and, in some circumstances, with serious difficulty. Challenges include violent face bursting and excessive tailgate convergence outby the face, which can be crippling to ventilation. The use of interpanel barriers, i.e., barriers left between longwall panels, offers one possible solution to mining under deep cover with bump-prone geology. Interpanel barriers have already been adopted by Utah's deepest longwall mine, and others are considering their use. The geomechanical implications of mining with and without interpanel barriers, and the competing tradeoffs between ground control and ventilation are discussed.

Jan 1, 2004

By Robert R. Thompson

Retreat pillar mining is highly productive but dangerous. The primary danger during pillar removal is premature caving of the roof. Because the safety of the miners is dependent on successfully controlling the roof, the roof must cave in a predictable and dependable manner. Temporary support during retreat is usually obtained by setting posts. They are set manually by a miner working in a dangerous area. A solution to this problem would be a system which could set and retrieve roof supports remotely and safely. The Bureau of nines has developed a remotely operated Mobile Roof Support (PIPS) machine which will place and retrieve temporary roof support. Two PIPS machines were fabricated under a cost-sharing agreement with Southern Utah Fuel Company and mining equipment manufacturer. Each machine carries four 50-ton jacks and is remotely- Controlled by radio. The machines are presently being used by Southern Utah Fuel Company under a long-team cooperative agreement. Not only have there been material and manpower cost savings in not having to set posts, but also the time saved bas resulted in increased productivity. The projected costs of mass-produced machines with tethered remote control rather than radio remote control are estimated at $150,000 each. The radio remote control is more expensive and is considered an optional extra.

Jan 1, 1986

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mine workers. Skin failures do not usually involve failure of the support systems but result from rock or coal spalling from between the support elements. For instance in 1997, over 800 miners were injured by roof and rib falls, of which 98 pet were the result of skin failures. Also, nearly 80 pct of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and roof and rib failures, in general, is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper features a review of the roof and rib accident statistics resulting from skin failure, highlighting the incidences by average days lost, in-mine location, state, MSHA District, and worker activity at the time of injury. A detailed analysis of recent fatalities caused by skin failure is included. Also discussed are the causes of roof and rib skin failures, current methods and support materials for skin surface control, as well as a historical literature review of skin failures and control methods.

Jan 1, 1999

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By David I. Hoyer

It is shown that by monitoring longwall leg pressures in real time, warning can be given for significant weighting events and the formation of roof instabilities, such as roof cavities, several hours in advance. Longwall Visual Analysis (LVA) is a software package that continuously monitors shield pressures and shearer position in longwall mines. LVA has been running on 19 Australian longwalls for up to four years, and as a result a very substantial database of shield pressure trends in a wide range of longwall situations has been collected. This database has been analyzed to develop indicators that will give operators and geotechnical engineers advance warnings of developing conditions such as weighting events and difficult roof conditions. LVA displays live charts of data, such as shield leg pressures, loading rates, and yield frequencies. Data analysis techniques were applied to historical data records from multiple longwall sites in order to develop a ?Cavity Risk Index? (CRI). The CRI indicates the risk of roof cavities developing, and it is based on pressure trends that indicate significant yielding and loading rates spanning a region of relatively low support. Case studies from different longwalls are given, showing how the CRI can give real-time advance warning of the formation of roof cavities with their anticipated location on the face. The limited number of case studies done so far indicate that the predictions have a high degree of reliability, but more work is required to quantify this.

Jan 1, 2011

By E. Bane Kroeger

Rib failure is a hazard that has resulted in many injuries and fatalities in underground coal mines, especially in soft coal seams. Conventional rib control methods including rib boarding, shotcreting. steel meshing and geogridding, are fairly expensive and time consuming to install. Some methods, such as rib boarding, have met with marginal success at controlling rib failure. Under this research, the Rib Strap System (RSS) introduced by Dr. Chugh in 1999, was modified and new components were added. Both bench scale and full size prototypes were tested in the labs at SIUC to determine the best materials for fabrication and easier methods for assembly and installation. This laboratory research has developed new methods of securing the strap ends to smaller rib hoards, a new device to post-tension two straps together, and a technique for replacing straps without having to drill new rib bolts or for retrofitting straps to rib hoards that are already in place. The method used to secure the strap end to rib boards developed during bench-scale testing was dubbed the wrapped staple technique. It is very simple, requiring only 10-15 staples, with the end of a strap secured to a rib board in about 45 seconds. Several different prototype designs for a new device to join the strap ends together and tension the strap were fabricated and tested in the labs at SIUC. The device, dubbed the rib strap buckle, was very easy to install and held the straps firmly. One specific buckle design worked extremely well during testing and exceeded all expectations. The laboratory research also developed a method of replacing a damaged rib strap that can also be used to add rib straps to existing rib boards. The technique uses nails, spacer blocks, and band clamps to secure the new board and strap. This technique was developed to allow one person to replace a strap using only a hammer and screwdriver, negating the need to drill and install a new rib bolt using mine equipment such as a roof bolter or scoop. In addition to the technical feasibility, the cost of materials for the rib strap system was compared to the rib boarding method currently being used at a mine in the Illinois Basin. The mine is using 20 rib boards on each pillar at cost of about $223.60. The costs for the rib strap system depend on the materials chosen for fabrication but for the base case, were about $97 per pillar.

Jan 1, 2004

By Lisa Burke

In underground coal mines, concrete block stoppings are widely used to control mine ventilation. Although stoppings are not intended as roof support, they are subjected to roof to floor convergence, and may fail as a result of this loading. Premature failure of stoppings can significantly affect mine ventilation, limiting the amount of fresh air reaching the working faces and increasing the risk for methane explosions. Softening materials are often used in stoppings to reduce the damaging effects of roof to floor convergence. However, to date, research has not focused on the behavior of stopping construction materials subjected to roof or floor loading, leaving the design process to trial and error. A combination of numerical simulations and large scale physical tests were employed to develop a scientific understanding of stopping performance. The first series of physical models were constructed using standard CMU (concrete masonry unit) blocks and tested in a load frame. The behavior of these walls was simulated with a distinct element model. A key finding was that very small variations in block size and irregularities in block shape significantly affect wall performance. These variations, which are inherent to the type of blocks typically used underground, create stress concentrations that initiate the failure of stopping walls. A second series of models employed concrete stoppings that incorporated woos planks, a shredded wood material, and foam planks like those commonly used underground. Numerical models were again able to match the physical test data. Analysis of the softening layers used in stopping construction indicated that the strength and stiffness of the material relative to that of the wall is crucial in determining the amount of roof to floor convergence the wall can withstand prior to failure. The product of this study is a numerical model that can be used to evaluate the performance of stopping materials and different wall geometries in a controlled environment. Testing was done in a laboratory setting with walls constructed on flat, parallel surfaces and subjected to uniform loading at a constant rate. Parametric studies with the model indicate that in this ideal environment it is possible to control the amount of vertical displacement the stopping can withstand by adjusting the number of softening layers built into the wall and the thickness of the layers. Additionally, under these conditions, the position of softening layers within the wall appears to have little effect on the amount of displacement walls can withstand prior to failure.

Jan 1, 2004

By C. A. Vining, J. R. Nopola

"Evaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. Evaporites are subject to continual creep and no amount of ground support can successfully arrest this process. Common ground-support techniques that are useful for most rock types may reduce the effective life of bolts in evaporite mines and can create unseen hazards. A different approach to ground support must be applied to provide long-term support in areas where high creep rates are present. The goal of effective ground-support designs in these situations is not to contain the rock and prevent it from moving; rather, the ground-support design must be able to move along with the rock and contain any fully detached slabs until additional remediation measures can be undertaken. The most appropriate ground-support designs will consider both the expected movement of the rock and the duration that the area needs to remain accessible.INTRODUCTIONEvaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. The factors that must be considered in design stem from the deformation behavior of salt, which can fail in a brittle manner, akin to most rocks, but can also deform in a slow, ductile manner, resembling the stretching and elongation of steel. The deformation behavior of salt has been well established in technical circles where it has been studied for decades (Hardy and Langer, 1984). Much of the research in salt mechanics is related to repository science, specifically at the Waste Isolation Pilot Plant (WIPP) in southwest New Mexico. RESPEC has been continually involved in the WIPP from the initial design considerations (Gnirk, Grams, and Zeller, 1977) to the current day (Keffeler, 2016) and has been able to leverage cutting-edge research of salt mechanics into practical solutions for mining operators. While a detailed description of salt mechanics is not provided in this document, Fossum and Fredrich (2002) include a fine overview of salt mechanics. The following list paraphrases their chapter on basic facts about salt to provide some context for the reader unfamiliar with salt mechanics:"

Jan 1, 2018

By M. V. Kurlenya

The experience of application of geomechanical investigations for substantiation of extraction of undermined ore deposit in the north of Siberia is discussed. The finite element method was used for forecasting the state of massif during the development of mining works. The results of calculations were compared with the experimental data of observations in situ for evaluation of authenticity of numerical modelling.

Jan 1, 1990

By S. N. Zhow

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. The strong outbursts often occurred in active tectonic lanes and areas of high stress concentration. In this paper, the author describes some characteristics of the strong outbursts and analyses the effects of ground stress, gas pressure and the properties of coal in outbursts.

Jan 1, 1987

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By Tim Burgess

Patton Mining, LLC and J.H. Fletcher Company recently collaborated and mechanized the sometimes hazardous, and always labor intensive, process of installing standing steel supports during the construction of a slope entry of a new mine. The new innovation is a beam setting machine design that can lift and maneuver heavy steel beams into place over and around the belt and vent tubing. In addition, the machine is designed with an integral double extending lifting work platform to allow workers a stable work area from which to install metal sheeting between the beams. The previous method to install the heavy steel supports and the steel sheeting included multiple workers lifting heavy loads frequently on stepladders. This paper will inform the reader of how Patton?s major goal to develop the safest, most continuous slope development process possible was achieved and the beam setting machine that evolved from the project.

Jan 1, 2011

By S. Q. Yang

Rotary radial jet improves greatly the pulsing velocity of airflow along each direction everywhere in the entry, intensifies transverse migration of air, eliminates effectively the local gas accumulation, and distributes methane concentration in airflow evenly and rapidly. According to the theoretical analysis of heat-transmission, mass-transmission and momentum-transmission, not only the similarity between heat-transmission and momentum-transmission, but also the similarity between mass-transmission and momentum-transmission exists in turbulent flow field, When the analogical equivalent ratio of heat transmission and mass transmission meets a certain criterion and remains a certain value, the temperature field can be used to simulate the methane concentration field. After hot airflow being released, thermograph instrument can be used to monitor the changing patterns of heat transmission and temperature distribution which simulates the changing patterns of methane transmission and methane distribution respectively. By analyzing these patterns and parameters of airflow field and methane distribution field during the process of local gas accumulation discharging by rotary radial jet, the dependability and validity of this discharging method are tested and verified.

Jan 1, 2004

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987