Search Documents

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

The Mining Foundation of the Southwest will host its 24th Annual American Mining Hall of Fame Awards Banquet at the Tucson El Conquistador Golf & Tennis Resort in Tucson, AZ on Saturday, Dec. 9. The Mining Foundation of the Southwest is a non-profit organization whose objectives are public education about the mineral industries. It also recognizes outstanding accomplishments in and contributions to the fields of fuel and mineral resources.

Jan 1, 2006

By J. R. Piper

“Old Borate,” located in the Calico Mountains east of Barstow, California, lead domestic colemanite production from 1884 through 1907. Mineral exploration at “Old Borate” in the early 1980's, examined borate mineralization in Tertiary lacustrine strata. Surface sample and drill hole locations, geology and structure, were hand-drafted on paper maps. To re-evaluate this data, the information was digitized using Geographic Information Systems software. Digital Elevation Model based terrain modeling integrated surficial samples with drill hole data to locate favorable drilling targets. Structural relationships were used to identify hypothetical resources formed by the leaching of boron from surface exposures, redeposited at depth.

Jan 1, 2001

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By Pat C. Hautala, J. R. Hoskins

This is a new era for the minerals industry. Never before has there been more need for effective communication. So said Robert Anderson, chairman and chief executive officer of Hanna Mining Co. He was speaking to the American Mining Congress's Communication Workshop. The question is whether there is enough industry concern to meet the challenge. Anderson observed that increased workshop attendance, in continuing tough times, reflects the industry's concern for communication. But, why were students, faculty, engineers, supervisors, and managers not at the conference? Communication applies to every manager, Anderson said. But he was the only operating manager present. And only one company sent operating supervisors. The remaining conference participants were public relations personnel, generally with nonmining backgrounds. And the program dealt mostly with public relations issues. Role of Communication in the Minerals Industry. It is well known that the minerals industry faces economic, political, and social problems. Economic shifts and foreign competition have created an international minerals industry and an international marketplace. This, in turn, calls for worldwide communication. Other factors effecting communication are: • Governmental protectionism as well as regulatory reforms call for increased interaction with governing officials. • Changing social values have created environmental issues and anti-industry attitudes. This intensifies the need for improved public relations. • Traditional work values are shifting towards self-actualization and humanistic movements. The work force is better educated and more informed. Employees demand more satisfaction, equality, and job autonomy. • The mining industry's task of managing its human resources is complicated by layoffs, job uncertainties, and bleak outlooks concerning employee morale and motivation. Technology and Information for a New Era As noted, this is a new communications era, one propelled by technology and information. Technology has led to reduced demand for raw materials by developing substitutes. Copper demand, for example, will never fully recover. Copper cables are replaced by fiberoptics; copper transmission lines, with aluminum. Technology has shifted the US from traditional to high tech and service industries. The speed, frequency, and scope of information transmission have greatly increased. But the most significant characteristic of this information is not the pace of advancing technology. It is the dramatic increase in the importance and frequency of our personal transactions. Knowledge has replaced raw materials and capital as the strategic resource. Information has replaced energy as the transforming resource. And the game against nature has become an interpersonal game (D. Bell, Post-industrial society, Physics Today, '76). In Megatrends, John Naisbitt says that information will soon double every 20 months. So, professionals will become "information workers." And communication will be the life channel of the information age. Thomas Wolfe said you can't go home again. Hanna Anderson said we are, indeed, facing a new day. It will never again be "business as usual." We must move into the information age with the rest of society. We cannot trust that the world will continue to rely on our products. Nor can we place the responsibility and control for problems and solutions outside the minerals industry. Improved communication is not a panacea. But, Anderson said, it is critical to the minerals industry. What is Communication? The word communication is overused. It is applied to every aspect of our lives. Satirist Tom Lehrer got sick of hearing about the need to communicate. He said, "It seems to me that if someone is having all that trouble communicating, the very least he can do is shut up!" Obviously, we cannot follow that advice (though we might wish that some others would do so). Communication is always going on. It is inevitable. Yet we have many misconceptions about com-

Jan 1, 1985

The two candidates in the upcoming presidential election in the United States each say that they have their own solution to the nation?s energy problems - solutions that will increase the amount of energy available, lessen the nation?s dependence on foreign sources and reduce the amount of pollution released to the atmosphere. Democratic nominee Sen. Barack Obama and Republican candidate Sen. John McCain both advocate research funding for coal-to-liquids and clean coal technologies. McCain also supports increased oil and gas drilling offshore. And Obama has even made some noises in that direction, although his plan leans heavily on the increased use of renewable energy sources. The energy debate is not new to this election. Congress and whichever party is in the White House has for years been trying to craft a comprehensive energy policy. One difference in this latest debate is that the increased use of nuclear energy has gained more attention. Current President George W. Bush has said he favors the increased use of nuclear power as part of the nation?s energy package. And McCain said he supports the building of more nuclear power plants. Obama has not said much about that. The American public is also showing signs of changing its stance on nuclear energy. To be sure, images of Three Mile Island and Chernobyl are still alive in some minds. However, the American public has said it wants cheaper energy and they want it produced more cleanly. With nuclear, the nation can have both. In the United States, nuclear accounts for slightly less than 20 percent of the electrical power used (see interview with Gary Steele of Energy Fuels on page 27). Globally, that figure is about 15 percent. And there are several nations that derive better than half of their power from nuclear sources. Add to that the world?s increasing need for more energy and the future of nuclear is bright.

Jan 1, 2008

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By G. A. Calboreanu

One way of cost reduction is attained when using materials with improved erosion ? corrosion resistance. For many years hard irons successfully answered the Mining Operation needs however application ranges were limited due to the low chemical resistance of such alloys. Corrosion resistance of any hard iron increases when microscopically homogenizing chromium and generating passivation conditions throughout and between all metallographic phases. Chromium distribution of the new material called Max10 was analyzed with EDS ? energy dispersive spectroscopy. At critical depleted chromium carbide ? matrix interfaces chromium increased to 31.72% which is well within passivation levels. Generally the corrosion resistance of high chromium hard irons provided by Metal Casting Industry is limited to 0.5% sulfuric acid and 28 PPM ionic chlorides. Such restrains increased when using Max10 to 2.0% sulfuric acid and 100 PPM ionic chlorides. Max10 contains 35% carbide volume fraction, has excellent corrosion resistance within pH = 1.15 ? 13.6 while fracture toughness under plain - strain conditions and Mode I opening is KIC = 20 KSI.(inch)1/2. Wear rate was calculated with the pin-on-disk apparatus using a diamond indenter per ASTM G99 recommendation. After years of research, experimentation and implementation the Max10 castings were service installed in slurry pumps and mixing equipment. In some applications the life time of slurry pumps manufactured in Max10 tripled versus previously used materials.

Jan 1, 2012

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By Tim O’Neil

Dressed in black tie and Victorian attire, some 200 people came to Leadville, CO, for a September weekend featuring a National Mining Hall of Fame and Museum (NMHF&M) induction banquet and a scenic mountain train trip to Fremont Pass and the Climax Mine. The 18th annual induction banquet on Sept. 17 began with cocktails and a open house. It was a chance for visitors to tour the National Mining Museum including the new Hennebach Wing, opened in February. The new wing is named in honor of Ralph Hennebach, retired chairman of Asarco. Formerly Leadville Junior High School, the Hennebach Wing encompasses more than1,440 m2 (15,500 sq ft) of floor space in two stories. One prominent feature is a 1923 Wills Sainte Claire touring sedan. Climax Molybdenum donated this first all-molybdenum steel motorcar. Docents were available throughout the museum to give banquet attendees directions and answer questions.

Jan 1, 2005

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005