Search Documents

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By Jerry Peterson

Mine maintenance planning, scheduling and daily workflow communications are crucial elements for enhancing overall efficiency and reducing costs. Equally important, it helps identify time periods that equipment will be unavailable so conflicts with production demands are avoided. The current CMMS Kennecott Energy Corporation (KEC) utilizes does not perform these functions in an effective manner. A solution to this problem was to develop an intuitive web-based maintenance planning, scheduling and work flow system call E-MESA. This paper will discuss the E-MESA'S system structure and advantages and disadvantages of using the web based E-MESA solution to perform the maintenance functions described above.

Jan 1, 2002

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By Gilles Cachia, Foteini Vasilikou, Seth Pollak, Hannes Lagger

"INTRODUCTION The Shatin to Central Link (SCL) is a new rail line being constructed by the MTR Corporation for the Government of Hong Kong to cater for the growing passenger demand between the North-East New Territories and the urban areas of the city. Contract 1103, which will provide the 4 km of running tunnels between the new Hin Keng and Diamond Hill Stations, was tendered in a design-build framework and awarded to Vinci Construction Grands Projets (VCGP) in October 2012, with Arup as Vinci’s lead designer. One of the most challenging pieces of work on the contract involved the construction of 133m of SEM mined tunnel on the northern end of the project. The Northern Mined Section (NMS) is an undrained, twin-track, single bore profile, broken out through the southern pipe pile wall of the Hin Keng Station cut-and-cover box, Figure 1. The tunnel has maximum excavated dimensions of 14.5m span x 12m height, with track spacing of 6.175m. The general excavation sequence consisted of 3 stages; a 6m high top heading (73.1m2), followed by bench (27.3m2), and invert (26.7m2). A risk-based approach to the design was taken given the large variation in rock level, cover, and an active stream course above tunnel crown. Ultimately, six different temporary support types were utilized in order to optimize the construction process through continually changing ground while maintaining a safe and stable excavation. Three main support types were developed during the initial design phase, along with a “contingency” case, which utilized a partial heading excavation sequence and enhanced face support. The purpose of the contingency support type was to have a robust, engineered design available for immediate implementation should unexpected ground behavior develop, leading to the breaching of instrumentation trigger levels. This support type was never implemented on site. Drill- and-blast tunneling commenced once 6m of rock cover was verified through forward probing. A robust instrumentation and monitoring scheme provided valuable data throughout excavation and the means to carry out a geotechnical back-analysis of the ground behavior and support performance."

Jan 1, 2016

By Peter E. Price

Salt dome hosted metallic sulfide deposits are the product of a complex evolutionary system involving halokinesis, cap rock development and diagenesis, and the generation, migration, and accumulation of basinal brines and hydrocarbons. Hydrocarbons play an important role in: (1) the production of calcite cap rock which hosts some of the metallic sulfide and sulfur concentrations, and (2) the generation of the reduced sulfur available for metallic sulfide precipitation and sulfur formation. Hydrocarbons and related fluids also are involved in the transporta¬tion and remobilization of the metals. Hydrocarbon consumption, in the course of cap rock development and sulfide mineralization at Hockley dome, is estimated to have been 6.4 million barrels of oil or 114 million cubic feet of methane. Mineral textures, including cap-rock banding, sulfide bands in anhydrite, and fine sulfide mineral banding indicate both episodic fluid influx and fluid compositional differences through time. Features such as pyrite "shells" and sphalerite and marcasite hemispheres may have been localized by hydrocarbon droplets and /or bacterial colonies. Marcasite mineralization in shallow strata above and flanking Hockley dome is best developed over the western and southern parts of the dome. This pattern mimics the known distribution of sulfide mineralization, which is dominantly marcasite, in the underlying cap rock. The iron sulfide paragenetic sequence in the sediments is pyritohedral and cubic + pyrithohedral pyrite followed by marcasite which is encrusted by cubic pyrite. Sulfur isotopic averages for the three stages are +20.8, -20.2, and +6.4 per mil, respectively. These values generally coincide with cap rock sulfate (+20 per mil), cap rock hosted metallic sulfides (-20 to +4 per mil), and sulfur in hydrocarbons (+5.8 per mil). Hydrocarbon compositions indicate provincial variations in oil composition and generation history. Long Point and Boling domes, which have an intergrown sulfide-sulfate-sulfur mineral assemblage indicative of mixed reducing-oxidizing environment, contain oils that are less mature than Hockley dome which appears to be more mineralogically segregated. Sterane biomarker compositions of the oils at Hockley, Long Point and Boling domes indicate a local, dominantly terrestrial source. An oil sample from supracap sandstones on the northeast flank of Hockley dome contained over 750 ppm combined Fe, Zn, Pb, and Co, indicating that hydrocarbons are carrying or remobilizing metals. Cap rock calcite and anhydrite also exhibit provincial variations in strontium isotopic ratios. Calcite and anhydrite cap rocks from several sulfide mineralized domes in the Houston diapir province have strontium isotopic ratios that are more radiogenic than Jurassic sea water (>0.7078). A calcite sample within massive sulfides at Winnfield dome also has a high 87Sr/86Sr ratio (0.7085). Variations in strontium isotopic ratios with strontium content indicate the mixing of at least three Sr-bearing fluids in the cap rock environment, one of which may have been the metal carrier. Anhydrite residues from diapiric salt have strontium ratios up to 0.7100, considerably more radiogenic than Jurassic seawater. These high ratios indicate either that salt and anhydrite recrystallized sometime post-Jurassic in the presence of a fluid with a high 87Sr/86Sr ratio, or that they precipitated in the Jurassic from a fluid with a higher 87Sr/86Sr ratio than Jurassic seawater. Salt domes with cap rocks containing metallic sulfides have only been found in basins that have geopressured zones. Waters from geopressured zones in the vicinity of mineralized salt domes have salinities that are two or more times higher and iron and base metal concentrations that are three to one thousand times higher, than geopressured fluids from other parts of the basin.

Jan 1, 2013

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By G. H. Roybal

Humic-acid-rich deposits exist in Arkansas, Florida, Louisiana, New York, North Dakota, Michigan, Minnesota, Texas, and Wyoming (Burdick, 1965) and in New Mexico (Shomaker and Hiss, 1974). New Mexico humic deposits are associated with coal in the northwestern part of the state where humate and weathered coal are presently mined. Discussion of the humic -acid industry in New Mexico requires an understanding of complex terminology and coal geology. TERMINOLOGY Humic material is not a pure substance so an ambiguous and complex terminology is in use by geologists, chemists, soil scientists, agronomists, and producers. Material mined for its humic-acid content is an extremely variable mixture of base-soluble humic, fulvic, and ulvic acids and their salts, formed during partial or complete decay of organic matter. This decay releases a high-molecular-weight organic material which is darkly colored, partly colloidal, and weakly acidic.

Jan 1, 1985

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Dominique Francois-Bongarcon

The rational and optimal determination of the design of a mining exploitation is a very intricate and difficult problem : the parameters are numerous, some technical, some economic or technico-economic which cannot be fully controlled; beside, deposits are estimated from very limited information and the choice criteria are not always quantitative, the economic context has to be anticipated by several years, and even the technological limits can change tomorrow. So, although very clever and performing numerical algorithms have been developed in recent years for open-pit design, we consider that this problem has not really been solved satisfactorily until now. The reasons are that people have concentrated their efforts on informatical algorithmical problems, and have assumed that the technical and economical data are well defined at the time of the study, which is generally not true. In particular, the mere fact of assigning dollar- values to blocks in order to maximize the total cash-flow is generally unrealistic because of the uncertainty of the data used. Consequently, the significance of the unique pit obtained as a result of these algorithms is questionable.

Jan 1, 1981

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By Richard Snyder

Secretariat of the Coal Mining and Mining Executive Committees' of the National Safety Council (NSC) and Manager of the memberships to both Mining Sections; Senior Consulting Safety Engineer, NSC; member of several committees for consensus Standards of the American National Standards Institute (ANSI); a Certified Safety Professional (CSP) of the Board of Certified Safety Professionals of the Americas, Inc. and a chief proctor for CSP testing and certification procedures, et al. It appears that the tunneling trade is merging into its own renaissance for the decade of the 1970s', and most likely on past the year 2001. Federal interest in underground excavation, and more specifically, rapid excavation expertise has been on the upswing since the latter part of the 1960's, mainly due to the pressing national needs for more raw materials based on the rise for material goods and the projective gloom of possible power shortages. On the pure tunneling side the national needs encompass, in the mainstream of priorities, rapid transportation and water supply excavation as the two top contenders. For instance, the estimates for tunnel mileage for the period 1968-1975 are:(1) Subways---85 miles Urban Highways--- 123 miles Intercity Highways---210 miles Water Supply Routes---528 miles at a total of 946 miles of tunnels. The estimated cumulative underground excavation demand in dollar amounts for the period 1970-1989 are:(1) Construction Oriented Demand--- $35 billions Mining Oriented Demand---$34 billions (which includes the coal-oriented demand on the order of 26 billions.

Jan 1, 1997

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By David B. Gladwin

Regional characteristics in the coal resource base have resulted in application of different mining methods across Canada. Longwall methods predominate in eastern Canada, whereas open pit, hydraulic and room-and-pillar methods are utilized in the west. Both provincial and federal agencies have regulatory responsibilities and both also share in the development of R&D programs. This paper outlines the scale and scope of the various agencies involved with health and safety R&D in our expanding coal mining industry. Specific R&D activities in ventilation, dust control, explosion hazards, tunnel boring, strata control and truck braking, which form part of the national program, are outlined.

Jan 1, 1982