Search Documents

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a part of the 21,296-acre Million Hills Wilderness Study Area (NV-050-233) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 46 miles south of Mesquite, NV. The area is on the east edge of the Gold Butte mining district and has had minor production of copper and zinc from the Azure Ridge mine in the early 1900's. Assessment work was being done on the Esperanta claims, which covers the mine workings, in March 1987.

Jan 1, 1988

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By Francis E. Federspiel

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resource potential of the Log Cabin Saddlebag, Hall Natural Area, Horse Meadow, and Tioga Lake RARE II areas in Mono County, California. These areas, along the east slope of the Sierra Nevada, are underlain by Paleozoic metasedimentary and metavolcanic rocks of the Log Cabin Mine and Saddlebag Lake roof pendants. The roof pendants are in Cretaceous granitic rocks. Pleistocene volcanic flows cap some of the older rocks, and glacial till and outwash locally cover the bedrock. The region was eroded by alpine glaciers. Four parts of the Log Cabin Saddlebag area have moderate gold and silver resource potential. Moderate potential for gold and silver resources was identified in one part of the Hall Natural Area and low potential for tungsten and molybdenum in two other parts (fig. 1).

Jan 1, 1982

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

By Forrest T. Moyer

INJURY experience in the metal and nonmetal mineral industries during 1964 was better in rates of occurrence but worse in severity rates than in 1963. The frequency rate of injuries per million man-hours was improved at metal mills, nonmetal mines, and sand and gravel operations, and was virtually unchanged at metal mines; however" the rate of occurrence of work injuries at nonmetal mills, stone operations, nonferrous reduction and refining plants, and slag plants was higher than in 1963. The severity rate of injuries during 1964, data for which are presented for the first time in this chapter, was better at metal mills, nonmetal mines, stone operations, and slag plants. However, the severity rate was worse at metal mines, nonmetal mills, sand and gravel plants, and nonferrous smelters.

Jan 1, 1965

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

By Frank G. Horino

This report presents a method of utilizing the Coulomb strength criteria for estimating the strength and stability of pillars and pit slopes containing planes of weakness. It is assumed that the Coulomb theory, as a special case of the Mohr envelope, is a satisfactory first approximation of failure in uniaxial compression or triaxial loading with low lateral loads. Accepting this assumption for brittle materials, an expression for the strength decrease of rock pillars containing a plane of weakness or fracture at any angle of orientation is derived. As few as six samples (three solid cores and three fractured cores at a failure-oriented angle) are required for testing uniaxially and triaxially to statistically determine the coefficients of friction and the shear strengths of both the solid rock and the fracture plane and the range of failure angles of the fracture plane. Interpretation of the data shows that the mean normal stress and maximum shear stress technique of analyzing the data is superior for solid core and that shear and normal stress values using angles of failure should be used for fractured specimens with failure-oriented angles. Plots of either the strength or strength ratios against fracture angles obtained from oriented drill core samples give a useful first approximation of strength decrease due to fracture. Using the same test conditions for both fractured and unfractured material increases the validity of the tests.

Jan 1, 1970

By Donald R. Alvic

For electric utilities serving the aluminum smelter industry in the United States, sulfur oxide (SOx) abatement legislation could bring about increases in the costs of generating electricity. This paper documents the method and assumptions used in estimating these increases, and the contains the results of the estimation. 1.2 SMELTER INFORMATION The smelters used in this study were identified by the Bureau of Mines (BOM) and are listed in Table 1.1. Also included in Table 1.1 are the electric utilities that serve these smelters. Compliance costs were estimated for these utilities. Some of the utilities are unique in the way that the information is handled or in the way the utility is operated; these are discussed below. 1.2.1 Big Rivers and Associated Co-ops, Data for Big Rivers and Associated Co-ops were gathered by George Mason University (GMU) students for BON and are included in this study.

Jan 1, 1988

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable capacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine owners and environmentalists alike.

Jan 1, 1976

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977