Search Documents

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By A. D. McMahon

This survey is one of a series of Bureau of Mines publications designed to serve the needs of Government and industry for comprehensive information on mineral commodities and activities. Copper, a versatile metal, has been vital to all civilizations from pre-historic times to the present. Its essential value in antiquity and until the nineteenth century arose from its malleability and ease of working, its corrosion resistance and durability, its attractive colors in alloyed and unalloyed forms, and, of course, its availability. The principal uses were for tools, utensils, vessels, weapons, pipe, statuary and other objects of art, and for building and architectural purposes where formability, permanence, and beauty were necessary qualities. Utilization of copper based on these physical and mechanical properties has grown tremendously for commercial, structural, mechanical, architectural, and art items; and its capacity for forming numerous alloys has led to a myriad of applications from miniature copper and brass eyelets to huge bronze battleship propellers. The early nineteenth century marks the epoch of the greatest use of copper, transmitting electrical energy. This particular property of copper is fundamental to the spectacular growth of the electrical industry and all associated industries relying on electricity for power, light, and heat. More than half of all copper produced is used for transmission of electricity.

Jan 1, 1964

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By R. W. Van Dolah

A premature detonation of an explosive charge occurred on January 30, 1961, at a face being prepared for blasting in the underground Jefferson Island Salt Mine, Diamond Crystal Salt Co., Jefferson Island, Iberia Parish, La. The accidental blast injured the powderman fatally; his helper was injured also, but recovered. The accident represents the first fatality reported to the Bureau of Mines in connection with the use of ammonium nitrate-fuel oil (AN-FO) blasting agents in underground mining in the United States. Representatives of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activity conducted the investigation, upon request of the manufacturer of the ammonium nitrate being used and with concurrence by the mine management.

Jan 1, 1962

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By Rudolf E. Greuer

This study concerns itself with two topics of the mine ventilation - mine fire interface which, when the work for this study began, did not seem to receive sufficient attention. Section 1: Comments on Spontaneous Combustion of Coal in Mines It is attempted to describe heat generation, heat and oxygen transport, in such a way that existing experimental data for U.S. coals can be used to assess conditions inducive to spontaneous heatings quantitatively. Investigated are, in particular, critical air velocities, minimum sizes of coal accumulations, moisture contents and the influence of mining factors. An extensive, practice oriented literature survey is included. Section 2: The Early Detection of Mine Fires by Assessment. of Mine Gases The suitability of the major constituents of combustion products for an early detection of fires is discussed. The same is done for gas concentration ratios. Since it was felt (at least at the time when this report section was written) that the value of the carbon monoxide/oxygen deficiency ratio was overestimated, the usefulness of monitoring this ratio as compared to monitoring CO concentrations was critically investigated. The state of art concerning instrumentation and organization of fire detection systems is reviewed also.

Jan 1, 2011

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By Christopher Mark

This proceedings volume contains papers presented at W U.S. Bureau of Mines (USBM) technology transfer seminars on New Technology for Longwall Ground Control. These seminars were conducted in Washington, PA, on April 12, 1994, and Denver, CO, on May 10, 1994. The papers herein describe several new, highly practical USBM technologies now available for ground control in longwall mines, including lie Coal Mice Roof Rating (CMRR), cable bolts, the MULSIM/NL model, and the Wood Crib Performance Model. Other significant topics addressed include longwall panel layout, coal pillar design, horizontal stress in longwall mines, roof support selection for gate entries, and ground control monitoring.

Jan 1, 1994

According to contemporary psychophysical theory, the relationship between the strength of a perceived sensation (S) and the intensity of a physical stimulus (1) is best expressed by a power relationship.(1) S=kln (1) This psychophysical principle has been applied to many practical problems, including the development of scales or guidelines for effective temperature, loudness, brightness, and ratings of perceived exertion. Based on the results of a number of experiments using a variety of scaling methods and a number of different muscle groups, the pooled estimate of the exponent for muscular effort and force is 1.7.(2) When applying this principle to work situations, it is assumed that individuals are capable and willing to consistently identify a specified level of perceived sensation (S). For manual materials handling tasks, this specified level is usually the maximum acceptable weight or maximum acceptable force. These phrases are defined by the instructions given to the test subject:(3) You are to work on an incentive basis, working as hard as you can without straining yourself or becoming unusually tired, weakened, overheated, or out of breath. If the task involves lifting, the experiment measures the maximum acceptable weight of lift. Similarly, there are maximum acceptable weights for lowering and carrying. Such tests are isoinertial in nature; however, in contrast to the tests described in Chapter 3, they are typically used to test submaximal, repetitive handling capabilities. Data are also available for pushing and pulling. These are reported as maximum acceptable forces and include data for initial as well as sustained pulling or pushing. Why Use Psychophysical Methods? Snook identified several advantages and disadvantages to using psychophysical methods for determining maximum acceptable weights.(4) The advantages include: • Realistic simulation of industrial work (face validity); • Ability to study intermittent tasks (physiological steady state not required); • Results are consistent with the industrial engineering concept of "a fair day's work for a fair day's pay"; • Results are reproducible; and • Results appear to be related to low-back pain (content validity).

Jan 1, 1998

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By David C. Benson

This Bureau of Mines report is an update of IC 8725 and comprises tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 535 projects for which information is provided, 429 concern coal mines and electric generating plants (including Energy Supply and Environmental Coordination Act (ESECA) coal conversion notices).

Jan 1, 1978

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined to determine through evaluations in two mining companies whether it would achieve measurable improvements. This volume describes the model, how it was applied in the field, and how it was evaluated. Anecdotal data to illustrate common kinds of safety problems and their solutions are included. The literature and field research that preceded the model definition is discussed in Vol. 2, which covers the period of September, 1980 to September, 1981.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983