Search Documents

By Jeremy Bosman, Niel Lourens

"Cyclones are used in four main applications in primary wet heavy mineral processing plants i.e. upfront desliming, densifying, and concentrate stacking and tails deposition.UPFRONT DESLIMINGMany heavy mineral ore bodies are associated with high slimes varying from 15 to 60%. The increased viscosities arising from the slimes impact negatively on heavy mineral recovery in the spiral plant. Recoveries can be reduced by up to 10%. Cyclones have proven to be able to remove slime efficiently with acceptable loss of valuable heavy mineral in the overflow. For low slime applications, typically below 25%, it is possible to achieve the desired results using a single stage of cyclones, whilst for higher slimes, two stages of cyclones are required. The overflow of the primary stage is retreated through a second stage to minimize heavy mineral loss."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels."

Jan 1, 2003

By Peter N. Holtham, Geoffrey J. Lyman, The University of Queensland, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong

"The cyclone would have a claim to be the commonest, least understood and most abused piece of mineral processing equipment available for study by researchers. It has certainly generated its fair share of publications – 1,000 in the last 60 years would be a fair estimate. However this remarkable degree of interest and scale of investigation is not reflected in our understanding of how they work; cyclones are still installed inappropriately and run poorly, which suggests that there are still things to learn about this deceptively simple process.In mineral processing there are two broad classes of cyclone: the hydrocyclone, used in classification, thickening and dewatering, and the dense medium cyclone, used for concentration by density. Although rarely studied together, the laws of physics presumably apply equally to both and so it seems that there would be interesting things to learn by considering them as a single class of device. The good news is that in recent years there have been spectacular advances in the computational and measurement tools available to study these devices, including computational fluid dynamics (CFD), tomography, and laser doppler anemometry (LDA), and some good progress has been made in an understanding of the fundamental principles involved.The JKMRC has made many experimental studies of hydrocyclones and DM cyclones, leading to useful empirical models. However some recent CFD and tomographic work, in association with work of other institutions, has thrown important light on the workings of these processes. Progress has also been made in novel designs of cyclone to achieve improved separating efficiency, based on an attack on the subprocesses believed to contribute to inefficient operation. This paper describes the work to date.Modelling of the dense medium and classifying cyclone was conducted using the Fluent computational fluid dynamics code. Three phase simulations of the dense medium application (air/water/medium) showed appropriate medium segregation effects but over-predicted the level of segregation compared to segregation measured by gamma-ray tomography. This is believed to be because the basic Algebraic Slip mixture model in Fluent does not model any back-mixing of the dispersed phase due to turbulence."

Jan 1, 2003

By Johan C. van Dyk, Johan W. van Zyl, Martin J. Keyser

"Coal is a crucial feedstock for South Africa’s unique synfuels and petrochemicals from coal industry and it is used as the main feedstock to produce synthesis gas (CO and H2) via the Sasol-Lurgi Fixed Bed Dry Bottom gasification process. Detailed coal characteristics are essential to predict gasification behaviour when a specific coal source is to be gasified.The principle aim of this paper is to highlight and discuss those specific coal characteristics, which affect gasification behaviour and stability.In order to determine the suitability of a coal source for gasification purposes, the coal is characterized and the results compared with historical data. Benchmark data, where it was possible to operate the gasifier with ease and relatively high stability, is used as a reference.Coal sources with extreme properties (i.e. low reactivity, ash content <10% as is used by Dakota Gasification Company, or “brown coal” with moisture >30%) can probably be gasified in a Sasol-Lurgi Fixed Bed Dry Bottom gasifier provided that certain operational changes are implemented. Other properties, like high caking and extreme ash content for example, require blending to acceptable levels."

Jan 1, 2003

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By Konstantin Fedotov, Victor Beloborodov, Anatoly Potyomkin

"There are areas in Russia, which cover huge territories and they are north, and Siberia. These difficult to access regions with cold climate are rich in a great number of distant deposits of valuable and rare metals, gold and platinum. The development of such deposits requires highly effective technologies of mineral processing which could be realized in modular and quick-built processing plants.The work presented includes the results of long term research in the development of new technologies of processing of zirconium (in the form of rare mineral Baddeleyite – natural zirconium dioxide) bearing ore of the Kovdor deposit which is located in the Polar region of the Kola peninsular and also in Siberia deposits of of ledge ores of gold."

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

By Wang Xiaotie, Yu Yongfu, Che Liping, Zhang Fuguang

The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.

Jan 1, 2003

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By Harri J. Lehto, Marja I. Oja

"The purpose of grinding circuits is to produce a particle size distribution that has as much as possible the wanted particle size class. In practise, however, the production of the wanted size class is not at all as simple as it sounds. In the case of industrial minerals for example the end user may give very tight specifications for the particle size distribution and for the chemical composition of the product. This leads in many cases to a very demanding grinding process, if we want to reach and maintain these specifications. In other words, the required size distribution is not necessary the best possible for the chemical composition.Screen models aim to predict the size distribution and flow of the products when a feed size distribution, feed tonnage, and grade efficiency curve are known. The approach used in this study was to select the most suitable empirical model for classification. Suitability of the existing models has been evaluated and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model.The performance of a screen was evaluated in order to minimize the amount of fine material in the screen overflow. The experiments were carried out using Derrick single-deck screen, first alone with recycling and then in the closed circuit with a rod mill using two different scales. The separate screen tests showed the expected behaviour of the grade efficiency curves. In the pilot tests the Leonard screen efficiencies stayed almost constant. This suggests that the screen works better in a milling circuit. However the loading of the screen turned the product of the mill coarser that helped screening. The grade efficiencies obtained from the pilot tests had the same general shape. The regression analysis of the pilot test runs did not give an acceptable correlation for the parameters. This suggests that pilot tests cannot be directly used to scale or to optimise industrial milling circuits. However they can be used to predict the trends of behaviour of an industrial circuit."

Jan 1, 2003

By Jochen Petersen, Harro von Blottnitz

"The landfill disposal of slags is common practice in the metallurgical industry. Chromium may be a minor constituent in many cases. It is present mostly in the form of chromites, which are considered environmentally benign and hence safe for disposal. Wastewaters from metal finishing operations are most commonly treated by reduction and precipitation of dissolved metals, including chromium, by lime addition, and subsequent landfill disposal of the resulting sludge. The metals contained in such sludges are mostly in the form of hydroxides, and as such considered environmentally stable.Thermodynamically, trivalent chromium, which is the predominant form in these waste materials, can be oxidised to the hexavalent form by atmospheric oxygen. Detailed research work on both slags and sludges has shown that a gradual emergence of hexavalent chromium can indeed be observed. The mechanism is governed by close physical contact between chromium oxide (or hydroxide) phases on the one side and calcium oxide (or hydroxide), which is present as flux in slags and residual lime in sludges, on the other. If oxygen can migrate to the points of contact, gradual formation of calcium chromate ensues.Hexavalent chromium is associated with high environmental toxicity, and hence undesirable in landfilled materials. Moisture migrating through landfill deposits can mobilise the highly soluble chromates and thus potentially transport them into natural waterways. Such gradual release from stainless steel and ferrochromium slag deposits has been demonstrated in a column experiment."

Jan 1, 2003

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By Daniela Venter, Stephen Chryssoulis, Ken Stowe

"A sampling campaign was conducted at Kemess in order to identify and assess the chemical and physical factors, which control free gold flotation kinetics in the rougher and cleaner circuits. The rationale behind this approach was that accurate knowledge of the parameters affecting free gold flotation kinetics, can be used to determine how to accelerate free gold flotation. Collected samples were composites of 5-6 cuts over a four-hour period, at steady plant conditions.In the rougher circuit, coarser equidimensional gold particles floated ahead of the finer grained and the flaky gold. Sulphur followed by molybdenum and to a lesser extent silver enhanced gold flotation kinetics, while hydroxyl followed by carbonate ions induced depression."

Jan 1, 2003

By Chris A. Bennett, Glenn S. Dobby, David A. Bulled

Establishing reagent dosing strategies for new ore bodies has traditionally involved a combination of experience and empirical experimentation using standard laboratory tests. The grade and recovery data resulting from these lab tests have historically been used as direct indicators of plant performance despite the obvious differences between the flotation environments. A reagent scheme selected in this way would subsequently be employed to generate the grade and recovery information for the geometallurgical model which in turn was used for metal production and cash flow forecasts. If the reagent scheme was sub-optimal then so too would be the forecasts and the resulting cash flow.

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of some silicate minerals (i.e., feldspar, quartz and wollastonite) after contacting different triboecharging medium made of different materials were studied. The charge acquisitions by different size fractions of minerals were monitored and accordingly the energetic work function values, i.e., the main parameter determining the entity of triboelectric charges acquired by mineral grains, of the examined minerals were estimated. Moreover the separation behavior of different size fractions of these minerals through the electric field of a laboratory free-falling separator when the mineral grains are charged by different tribochargers were observed and considered as the electrical separation potential of the examined minerals.Furthermore, the role of adsorption of different chemical species on triboelectric charge characteristics and charge acquisition of mineral samples were described from theoretical point of view and the effects of some chemical reagents on triboelectric charge acquisition of the examined minerals were studied. In addition the separation behavior of chemically conditioned quartz, feldspar and wollastonite minerals, using different anionic and cationic reagents, through the electric field of a free-fall electrostatic separator before and after chemical conditioning were monitored.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing mainly of feldspars, quartz, and wollastonite. Different separation tests under various conditions were conducted to this complex silicate ore. Before passing through the separation device, the ore sample was conditioned by different cationic and anionic reagents and then was triboelectricaly charged by different tribocharging medium in order to find the effective reagent and tribocharging medium for separating silicates. Besides the role of temperature and humidity of the surrounding ambient in separation behavior were considered."

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003