Search Documents

By Hennie F. T. Barnard

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes? operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

By Hennie F. T. Barnard, Theodore E. B. Vorster

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes’ operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

Jan 1, 2017

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By Dempsey S. Thieman

The Kuparuk River Central Channel Bridge on the North Slope of Alaska provides critical access for oilfield service vehicles in the largest oilfield in the United States. The original sloped spill-through bridge abutments were protected by articulated concrete revetment. After 27 years of heavy service, ice impact, deep river scour, and high floods, the revetment required replacement. An OPEN CELL SHEET PILE® abutment was selected to replace the existing erosion protection and provide increased performance and structure life. Project engineers and contractors successfully addressed the challenges of low overhead sheet pile installation under the bridge, extremely heavy vehicle loads, and arctic winter construction conditions through innovative design and construction techniques. The project was successfully completed on schedule with minimal disruptions to critical bridge traffic. This paper provides a detailed discussion of the design and construction techniques utilized to address the challenges of the project, many of which could be adapted to other projects.

Jan 1, 2008

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By M. Hesham El Naggar, Tony Sangiuliano, Alper Turan

"Bridge abutments supported on pile foundations are often constructed over weak and compressible soils. The consolidation settlements induced by the embankment loads are known to result in downdrag and lateral forces on the piles supporting the bridge abutments. The performance of a pile group including inclined piles embedded in consolidating soils was investigated numerically considering surcharge loads from approach embankment construction. A two-dimensional numerical model was constructed using commercial finite element software PLAXIS and calibrated against field measurements of the abutment movements observed on Brookdale Avenue Underpass Structure located on the Macdonald-Cartier Freeway in Ontario between Cornwall and the Quebec border. The soft soil model (SSM) was used to simulate the constitutive behavior of the compressible soil deposit. The SSM model parameters were determined based on the laboratory tests. Subsequently, time dependant development of downdrag effects was comparatively evaluated for vertical and inclined single piles as well as a pile group that included both vertical and inclined piles.Results showed that drag loads increased with the consolidation time. However, majority of accumulation of drag loads took place within first 120 days after installation of piles. The results also indicated that the shear forces and bending moments are controlled by the lateral spreading of foundation soil and their accumulation is proportional to consolidation time. The large axial strains caused by large downdrag forces are considered to have yielded the piles and this is a possible reason for unusual abutment movements. The results presented in this study are considered to be of interest to researchers and practitioners.1. IntroductionDeep foundation units are widely used for supporting bridge piers and abutments, where weaker surficial soils preclude shallow foundations. Particularly in Ontario, semi-integral and integral abutment bridges are typically supported on end-bearing steel driven piles. The construction of approach embankments over weaker, compressible soils results in significant vertical and lateral soil movements, which induce additional loads on piles supporting the abutments. In order to minimize such effects, preloading and surcharging are commonly employed approaches to avoid unanticipated settlements prior to the installation of piles. Other alternatives such as aggregate pier supported approach embankment are also being studied as the schedule restrictions imposed by preloading and surcharging becomes cost prohibitive (Turan et al. 2012)."

Jan 1, 2015

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By Deepak Pappusetty, Miguel A. Pando

This study is motivated from the increased interest in recent years to explore use of Ocean Energy Converters (OEC’s).OEC’s can be tidal or generate electricity from wave or current action. Design of foundation systems for these OEC’s is a key consideration as it can represent about 35% of the initial installation cost. The primary focus of this paper is related to foundation systems involving monopiles where a key design consideration includes gradual accumulation of pile head deformations beyond serviceability limits of the OEC. This design consideration is important since these foundation systems are often subjected to more than 108 low amplitude repetitive dynamic load cycles during a normal 30 year design life. Research on single model piles installed in sand and subjected to over 104 low amplitude lateral load cycles have shown that pile head displacements and rotations tend to increase gradually with increasing load cycles. This gradual development of pile head deformation is related to plastic strain accumulation in the soil in the vicinity of the monopile. Analytical methodologies based on conventional p-y curves typically cannot predict these accumulated pile head rotations and displacements. Even 3D dynamic Finite Element Analyses may not capture this response for several conventionally used soil constitutive models. This manuscript presents predictions using p-y based methods as well as 3D dynamic finite element analyses. The different numerical predictions are compared to available experimental data. Results from this study show that conventional p-y methods do not predict the gradual pile head displacements observed experimentally. Modified p-y curves, developed for cyclic loading, do a better job than conventional p-y curves but tend to greatly under predict deformation. This is believed to be related to the cyclic load test data used to develop these cyclic p-y curves which involved at most up to 500 cycles and did not include high frequency contents or partial unloading cycles. The 3D FEA captured reasonably well the general observed trends of gradual accumulation of pile head rotation and lateral deformation with increasing constant amplitude lateral load cycles.

Jan 1, 2015

By Edmund J. Cardoza

The Detroit Water and Sewerage Department (DWSD) provides water and wastewater services to the Greater Detroit Metropolitan Area. Sewerage is treated at the DWSD Wastewater Treatment Plant (WWTP) located at 9300 W. Jefferson Street south of the City of Detroit, Figure 1. PARTICIPANTS Engineering and design of the project for the DWSD was performed by Harza Engineering Company, Inc., C.C. Johnson & Malhotra, P.C. and their sub-consultants, including Worley Engineering and Wade Trim. The Prime Contractor is a Joint Venture of Traylor Brothers, Inc. and Jay Dee Construction. The shaft drilling and riser installation was performed by The Millgard Corporation in joint venture with the Prime Contractor (MTJD). The selection of specialized drilling equipment and the supervision and performance of the access shaft and riser installations was primarily the responsibility of The Millgard Corporation (TMC).

Jan 1, 2001

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By David R. Sutfin, Joseph Lodde

110 N. Carpenter is new commercial building located in the West Loop neighborhood of Chicago, Illinois. The new home to the McDonalds Corporation work headquarters, accelerated project delivery methods were essential to meet the scheduling demands for this project along with other projects slated to start in the region. As such top-down construction methods were utilized to allow for above and below grade construction to proceed in parallel in lieu of more conventional bottom-up construction methods, thus compressing the project schedule. To achieve this plan, perimeter secant pile walls were constructed in conjunction with interior columns/drilled shafts and a shear wall core constructed from inside a temporary cofferdam. The use of secant pile walls allowed for efficient accommodation of a variety of loading conditions including: exterior curtain walls loads, perimeter column loads, tower crane foundation loads, and in-plane shear loads. Furthermore, this system allowed for efficient and fluid operation of equipment on site in order to accommodate the 90-day window allotted for initial foundation construction. INTRODUCTION 110 N. Carpenter is a recently-constructed 9-story commercial building located on the old Harpo Studios property in the West Loop neighborhood of Chicago, IL. The construction of this 55,750m2 (600,000 ft2) structure is significant to the continued commercial development of Chicago as nearly 46,450m2 (500,000 ft2) of the building houses the new world headquarters for the McDonald’s Corporation, which had moved from Chicago to the suburb of Oak Brook in 1971. McDonald’s recommitment to this urban environment is not only a reinvention of the long-established fast food giant but the anchor for a broader redevelopment of the West Loop neighborhood. Since the opening of this building was seen by the developer, the City of Chicago and others as a key to future local projects, innovative solutions were required to showcase forward-thinking design as well as expedite the construction process. The final result of the design/planning process is a structure consisting of nine levels of above-grade commercial space and two levels of below-grade parking, providing approximately 300 parking spaces. The above-grade structure consists of a reinforced concrete flat plate system, including two-way slabs, columns, and two core/shear wall systems for lateral support. With an average depth of 7m (23ft), the below-grade structure consists of interior components similar to the above-grade structure (structural slabs, columns, shear walls) but includes a perimeter secant pile wall that was designed to support lateral earth pressures; vertical forces from the exterior curtain walls, perimeter columns, and the construction tower cranes; and in-plane lateral forces to reduce the demand on and quantity of interior shear walls. The use of a secant pile wall is a key component to the project because it accommodated the use of top-down construction methods to accelerate the construction schedule.

Jan 1, 2019

By Gianfranco Di Cicco

Seepage problems were recorded for more then 40 years at the Walter F. George lock and dam. In 2001 the Mobile district of The U.S. Army Corps of Engineers turned to the installation of a 200 feet deep cut-off in a final attempt to remedy the situation. The advertised design-built contract requested the installation of the cutoff wall in front of the concrete structure of the dam starting from 90 feet of water, cutting through a concrete lock structure, a submerged retaining wall and extending on both sides on the earthen embankments. This paper summarize the history of the project and the installation of the first recorded cut-off wall constructed under deep water, upstream to an existing dam structures and under an existing concrete lock. The technology used combined with the project's results may be considered a milestone in the marine foundation and the marine cut-off wall construction technology.

Jan 1, 2013

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009