Search Documents

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By M. Churchill, V. R. Degner

"Over the past two decades, declining ore body grades, increased operating costs and increased construction costs have provided an incentive for the development of progressively larger flotation machines. As a consequence, the 60 to 100 cubic foot flotation machine of the l950's and l960's is being rapidly replaced by large volume machines, with a resulting improvement in the flotation machine specific capacity (TPH processed per square foot floor space), specific power (HP per TPH processed) and process control simplicity. The recent development, and satisfactory plant evaluation, of the WEMCO 1000 cubic foot flotation machine provides the means by which further economic and operating advantages may be incorporated in high tonnage mill applications.The systematic development of the large 1000 cubic foot flotation machine, and its subsequent performance evaluation in beneficiating metalliferous ores (copper, zinc and iron) will be reviewed in this paper and recently completed plant results will also be provided."

Jan 1, 1982

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By Stephen L. Chryssoulis, Daniela Venter, Stamen Dimov

"Comparative surface analysis of floated and rejected free gold grains from a number of full scale benefication plants and from pilot plant testwork, has shown silver (the most common impurity in gold) and sulphur invariably in greater concentration on floated gold grains, implying that they assisted gold flotation (gold activators). Collector loading measurements on individual gold grains from concentrates of staged rougher flotation tests on a cyclone U/F product of a pyritic gold ore, revealed first progressively lower concentrations of the collector monomer on gold from each follow-up concentrate and secondly a direct proportionality between the surface concentration of silver and the collector monomer. These two observations leave no doubt that silver activates gold and that collector monomers play a significant, previously not fully recognized role in gold flotation.INTRODUCTIONGold to some degree is naturally floatable in industrial systems, which means that it can be recovered without collector addition (Marsden and House, 1992). This is due to the adsorption of hydrocarbons and deposition of sulphur, which are dependent on the metallic properties of gold, particularly its high electrical conductivity, which allows surface electrochemical reactions to occur catalytically and selectively. Cyclic voltammetry has shown that gold can be rendered hydrophobic by deposition of a surface layer of sulphur (Sº) from S2- and HS- solutions (Walker et al., 1984). Twenty monolayers of sulphur were required to produce a hydrophobic gold surface.However, no sulphide flotation plant relies solely on the natural floatability of gold for its recovery. Gold hydrophobicity is enhanced by the addition of flotation collectors such as xanthates (X), dithiophosphates (DTP), dithiophosphinates (DTPI), mercaptobenzothiolates (MBC) etc., as used in sulphide mineral flotation (Dekok, 1973: Adams et al., 1986). The mechanism invoked in enhancing the hydrophobicity of pure gold with the aforementioned four groups of collectors is similar to that of pyrite, whereby collector anions are oxidized at the gold surface to form dimers (Groot, 1987; Marsden and House, 1992; Basilio et al., 1992) As an example, xanthate ions are oxidized at the gold surface to form the neutral dimer dixanthogen (X2):"

Jan 1, 2003

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By Don A. Toth

Until recently, the fire protection systems used to protect mining equipment were based on generically designed, off the- shelf concepts. These systems were reliant on single agent approaches and were generally comprised of a series of small twenty or thirty pound chemical canisters that would discharge their contents when triggered by thermal detection means. As the equipment grew in capacity, the logic used to increase the protection was to add more chemical canisters to the system. Hydraulic excavators and large-scale mining trucks grew dramatically in size into the 1990?s and beyond; with this growth came the increase in major losses due to fire. This was evidenced throughout this period, and continues to be of great concern today. During this presentation you will learn of the significant changes that have come about as a result of this history. Today, dual-agent products, infrared detection and unit-specific, engineered systems are the primary phrases used when discussing how to best protect this equipment from fire loss. This session is a must for anybody looking to optimally protect their equipment assets and for those looking to renew and/or secure new insurance for high value equipment in the future.

Apr 1, 2005

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985