Search Documents

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By Russell McIntosh

"The Madsen mine is in the southeastern part of Baird township, in Red Lake area, Ontario. It lies about 6 miles southwest of the town of Red Lake, with which it is connected by an all-weather road.The Madsen Red Lake Gold Mines Company was formed in March, 1935, to take over the holdings of the Falcon Gold and Jomac Gold syndicates. During 1935 an4 the early part of 1936 No. 1 shaft was sunk and drifts driven on four levels, all on a narrow quartz vein in a granite dyke.In July, 1936, the Austin zone was discovered about half a mile north of No. 1 shaft by Austin McVeigh, a prospector employed by the Company. Diamond drilling showed that the zone included an orebody worth development, and in 1937 No. 2 shaft was sunk, three levels opened up and sufficient ore outlined to justify the installation of a mill. Milling commenced in August, 1938, at the rate of 300 tons a day, which was later increased to 400 tons a day.The total production from 1938 to 1946 was 1,116,307 tons from which gold and silver having a value of $9,949,010 were recovered. The gold produced ranged from a minimum of 0.1910 oz. a ton in 1939 to a maximum of 0.2827 oz. in 1944. The average grade in 1946 was 0.2345 oz. to the ton."

Jan 1, 1954

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By T. Schmidt, H. Assadi, F. Gartner, H. Kreye

Among all spraying processes, cold spraying has attracted a special attention in recent years, both as a coating - and more recently - as a rapid manufacturing technique. The interest in this process is mainly because of the fact that the deposition of spray material takes place at moderately low temperatures, and thus, oxidation and unfavourable microstructural changes can be alleviated. In this process, a highly compressed gas, flowing through a de Laval nozzle, accelerates the particles of the spray powder to high velocities of up to 1200 m/s. Although there is no melting of particles prior to impact on the substrate, cold-sprayed deposits can be denser and more tightly bonded as compared to the equivalent deposits produced by conventional thermal spraying methods. The present contribution focuses on this unique aspect of cold spraying. Modelling of particle impact, combined with various experimental observations, is employed to illustrate that bonding of particles and hence material deposition occurs through shear instability - associated with severe plastic deformation and localized heat generation - at the interacting surfaces of particles and substrate. The results of modelling also provide an insight to the influence of material and process parameters on the critical velocity and on the microstructural properties of cold-sprayed deposits.

Jan 1, 2006

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y&apos; phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys&apos; resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens&apos; resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By E. W. Johnson

"The current increase in gold price may presage a resurgence of gold milling plants in Canada similar to that of the thirties. Because the industry has been at a low ebb for almost two decades, future operating responsibilities will likely devolve upon personnel with limited cyanidation experience. My comments, which may seem elementary to experienced operators, are directed towards these industry newcomers to highlight operational features in cyanidation which forty years' experience has shown me to 0e of importance. A brief review of what actually takes place in a cyanide circuit may help give a better understanding of the topics to be discussed.These will include: (1) expose the gold (2) dissolve the gold(3) make solid/liquid separation(4) recover the gold from solution.1. Expose the GoldThe chemical key to gold recovery by cyanidation lies in the ready solubility of the metal in a relatively weak solution (0.04%-0.075% NaCN equivalent by weight) of calcium or sodium cyanide. Obviously, dissolution cannot start unless the cya1ide is in contact with the gold. As an analogy, the yolk of a hard-boiled egg can oe taken to represent the gold particle and the egg white and shell, the surrounding gangue or sulphide host. As the sl1ell and white must be fractured to expose the yolk, similarly the surrounding gorngue or sulphide host must be broken or fractured to enable the cyanide solution to contact the gold."

Jan 1, 1979

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006