Search Documents

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013

By Ellis Thomson

The microscope is now used extensively not only in the examination of solid ore but also in the determination of fragmental mill products. It has therefore become a matter of paramount importance to be able to mount and polish fragmental as well as solid specimens in the easiest and most efficient way, so that the minerals present may be readily determined. In the case of the solid ore the ordinary mount of plasticine set on a glass or metal slide serves for most practical purposes. An improvement on this is furnished by the small brass container inside of which the specimen is mounted in a cementing medium of sealing wax. The latter is the method in use at Harvard University. It has the advantage of uniform height, thus obviating the necessity of a slide of any sort. It is also easily catalogued as the brass holder may be stamped with a convenient series of letters and numbers that will serve as a label. Other advantages of this type are the ease with which any particular part of the section may be re-located, the excellent storing facilities afforded by mounts of uniform size, and the possibility of polishing ten or a dozen sections at the same time by means of a holder which is placed over the polishing wheel, is geared with it, but revolves the opposite way.

Jan 1, 1926

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By Norman J. Tienkaivip, Christopher J. Preston

"This paper describes the use of electronics for physical measurement and computer analysis in both open-pit and underground mining operations for the ultimate purpose of optimizing production blasts. Techniques in monitoring single borehole blasts using both pressure and vibration sensors to establish in-situ dynamic rock properties are outlined, including characterization of multiple borehole production blasts with regard to stress generation.Once field derived measurements are computer analyzed, they are channelled as input parallel to other data, such as the explosives thermochemical performance properties generated by a sophisticated computer program called ""HT-65"" into BLASPA . BLASPA, a blast simulation computer program, then couples these input with a mathematical model which defines the blasting processes. Aspects such as the blast geometry, explosive loads and distribution, hook-up, and costs are studied. The final output table gives specific blast performance or quality factors for each blast procedure. These results are then easily compared and rapidly optimized to achieve maximum performance at lowest blasting and drilling cost."

Jan 1, 1984

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By R. M. Clowes

"As part of LITHOPROBE's multidisciplinary earth science research program to understand the evolution of the North American continent, studies have been undertaken in a number of key areas in Canada. In the Trans-Hudson Orogen of Manitoba and Saskatchewan, LITHOPROBE results require re-evaluation of tectonic models related to its origin. In the Abitibi greenstone belt of Quebec and Ontario, results indicate a more complex evolution for the southern Superior province, one that links with the development of gold and massive sulphide deposits. As part of the program, the seismic reflection profiling method is being adapted for the mining industry. Three examples demonstrate the subsurface information that can be obtained. In Noranda, the base of the volcanic Blake River group is imaged and reflectivity is tied to geology through well logs; in Matagami, the zone of mineralization is shown to be downdropped along a majorfault; in Sudbury, a new structural model is developed, one that shows marked asymmetry at depth and indicates that some ore-bearing units on the margins of the igneous complex may be repeated at depth. IntroductionLITHOPROBE is Canada's national, collaborative earth science research project, established to develop a comprehensive understanding of how the North American continent has evolved. Ten transects, or study areas, were chosen to investigate pivotal geological features to their deep lithospheric roots. They span the country from the Pacific to the Atlantic Oceans and from the U.S. border to the Yukon and Northwest Territories, and geological time from four billion years ago to the present. A multidisciplinary approach, which is spearheaded by seismic reflection techniques, is essential to developing complete interpretations and outstanding scientific results. LITHOPROBE also has pioneered the use and demonstrated the value of using reflection technology to determine subsurface geology in mining camps.This paper provides an overview of the transects and their significance for the tectonic evolution of North America. Two specific examples demonstrate how we detennine present three-dimensional lithospheric structure and past geotectonic processes which formed it. The application of the reflection method to imaging complex structures in ""shallow"" crystalline rocks has been developed with funding and other support from the mining industry and provincial geological surveys. Sustaining funds, however, are derived from the Natural Sciences and Engineering Research Council and Geological Survey of Canada. Emphasis has been placed on developing deeper penetrating tools for exploration of deeply buried, but economically retrievable, mineral resources near existing mines, where an expensive infrastructure already is in place. Three examples, Rouyn-Noranda in western Quebec, Matagami in northwestern Quebec and Sudbury in northeastern Ontario, illustrate these developments."

Jan 1, 1994

By Yan Germain, Université Laval, Bernard Dallaire, Jocelyn Bouchard, Peter Radziszewski, Gilles LeBlanc, Michelle Levesque, Nicolas Tremblay

"The comminution process is estimated to be only 1% efficient, resulting in waste energy dissipated as heat, noise, and vibration. Energy recovery from grinding circuits has not been implemented mainly because recovering heat from the surface of the grinding mill or from mill slurry can impede operation, increase maintenance requirements, and prolong plant shutdown time (and production). However, currently very little information is available in the public domain regarding the amount of waste energy and that potentially recoverable in the grinding circuit of a mineral processing plant. Availability of such information could drive innovation and improve decision-making regarding opportunities for waste energy recovery. The Canadian Mining Innovation Council (CMIC) has initiated a study with CanmetMINING and mining industry partners to develop a model to map the energy flows in grinding circuits and to quantify the potential for energy recovery. The paper outlines the underlying fundamentals and data requirements for use in the model and then focuses on quantifying the energy recovery potential of the semi-autogenous grinding and ball mill circuits at the Agnico Eagle Goldex Division. Results show that most of the electrical energy (over 75%) is used to heat the slurry, leaving only a relatively small amount of it to achieve mechanical work (~9%). INTRODUCTIONCanmetMINING commissioned a study in 2013 to better understand the barriers for adoption of new technologies in the mining industry (MNP, 2013). The conclusions highlighted the importance of enhancing industry/regulator engagement and communication to raise awareness and improve the industry’s comfort level with new technologies.In November 2014, the Green Mining Innovation Advisory Committee (GMIAC) held a workshop to explore the possibility of accelerating the uptake of green mining technologies by bringing together key stakeholders among the mining value chain to address industry priorities. Participants included representatives from mining companies and associations, academia, provincial governments and federal departments and organizations. Two key priority areas emerged at the workshop: i) energy saving, and ii) water management."

Jan 1, 2016

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By W. D. Watson

"Early in mine development at Quintette Coal Limited major problems were encountered with the fleets of primary equipment which seriously hampered production. These major fleets (cable shovels, hydraulic shovels, hydraulic drills and electric trucks) have consequently been the focal point of maintenance efforts. Some were prototypes in the Canadian mining scene and brought with them new concerns to test their skills. The problems were studied and the category and areas which were having the greatest impact on the reliability of the equipment were determined. Once defined, priorities were established and a program was initiated which was designed to accomplish a resolution. Resulting from implementation of this systematic approach, over the past three and one-half years, the fleets are now giving good reliability and industry standard availabilities. Along with these significant achievements, cost per operating hour on some of the equipment fleets has decreased substantially and continue a downtrend through 1987. This paper identifies the problems and describes the resolutions. IntroductionIn the early years of the mine development, Quintette Coal Limited (QCL) experienced production shortfalls due to problems with the major excavator and haulage fleets. A large fleet of hydraulic excavators had been purchased, and QCL was among the first northern users of all hydraulic blasthole drills. They were also using some prototype equipment and encountered problems which were not common on other types of equipment or were unknown.Because of these unique problems and lack of experience from other mines to draw on, an analytical approach was taken to areas and associated causes of the delays affecting the availability and reliability of equipment. This was done by dividing the equipment downtime into seven classifications of delays, i.e. maintenance, electrical, hydraulic, mechanical, damage, service and preventative maintenance, and tires; and then each was expressed as a percentage of total downtime. Subsequently each of the delay classification was divided into categories e.g. electrical to six categories - wheel motors, main alternator, relays, cards, no propel, lighting and 24 V system. Then, the basis for further study had been established.From this preliminary analysis of historic records, it was possible to determine the areas which were causing the majority of the downtime. These areas were then analyzed to evaluate causes and to determine possible solutions to the problem s. This paper addresses the major fleets, their problems and eventual solutions. Plea se bear in mind that the over-all objectives were to increase physical availability and reliability."

Jan 1, 1988

By P. R. Cook

Thunder Bay Terminals&apos; plant, now in operation, cost about 70 million dollars and was completed on time and under budget. The paper is the project manager&apos;s account of this accomplishment. From site selection through feasibility, engineering and construction to realization, he emphasizes the necessary philosophies for the control of time and money. The computer as a tool is discussed, as well as techniques for procurement.

Jan 1, 1979