Search Documents

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By Thomas Clark

This report presents a review of the distribution and exploration potential of platinum-group elements (PGE) in Québec; it is based on published and unpublished analytical data. This qualitative evaluation of the PGE potential, whether in PGE-dominant deposits or in Ni-Cu-dominant deposits with co-product PGE, is based on interelement ratios such as Ni/Pd, Cu/Ir, Cu/Pt, and Cu/Pd. Good PGE targets, i.e., deposits associated with magmas fertile in PGE, are identified. Less favorable PGE targets, i.e., deposits associated with PGE-depleted magmas, are also mentioned. The importance of exploring for deposits similar to those at lac des Îles and East Bull Lake (Ontario) is emphasized.

May 1, 2001

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By A. R. Pasieka, J. C. Wilson

"Compressed air still remains an essential source of power in underground hardrock mining. As a power medium it has a high convenience factor, although, in many cases, it is expensive to generate and maintain. Until new methods of breaking rock and/ or satisfactory alternatives to air-driven rock drills are developed, compressed air is indispensable. It is essential to utilize this source of power to a maximum by keeping all pneumatic tools supplied with air in adequate quantity and at optimum pressure.In search of the optimum operating air pressure, con-trolled drilling tests were undertaken at dynamic pressures ranging from 90 to 140 psi.Test results show the effect of increasing air pressure on: the performance of various jackleg drills at varying pressures, the life cost of drill steels and TC bits, and drilling efficiency at varying pressures. From the fore-going, a criterion is proposed for selecting efficient rock drills, and, also, optimum air pressure at each mine can be determined for its particular conditions."

Jan 1, 1966

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By C. G. McLaughlan

The Noranda concentrator was placed in operation in October, 1928, and the object of this paper is to outline operations during the twelve months which have elapsed since that time. The ores milled are massive sulphides carrying copper and gold, and, in certain cases, zinc. These ores have a specific gravity of about 3.8. The average assay of the copper-gold ore so far treated has been 2.0 - 3.5 percent Cu; 0.10 - 0.20 oz. Au; 40 - 51 percent Fe; and 6 - 15 percent SiO2. In this ore the copper occurs almost entirely as chalcopyrite, and the iron which is not combined with the copper is present mainly as pyrite and pyrrhotite. ?some iron is also combined with the silica, the ratio being about 1 to 4, and a small percentage is present as magnetite. The occurrence of the gold has been shown by microscopic work carried out by Prof. L. C. Graton, of Harvard University, to be very variable. Some of it is free, and is included within the base-metal sulphides or occurs at their boundaries. A similar distribution also holds for a portion of the gold which is combined as a telluride. Little is so far known of the occurrence of the silver other than that some of it may be combined with the gold in the telluride, petzite. The copper-zinc ore contains up to 6 percent copper, and has a very variable zinc content. The copper in such ore is present as chalcopyrite, and the zinc as sphalerite. In starting the mill we had three conditions to face; the first of these was climatic, the second was the lack of skilled flotation operators, and the third was the ore itself." The last of these three proved much more difficult to contend with than the other two combined.

Jan 1, 1930

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By F. F. Langford

"The Athabasca Basin occupies about 100,000 km2 of the northwest corner of Saskatchewan with its western margin extending about 50 km into Alberta (Fig. 1). The basin is filled with a Helikian sequence of predominantly fluvial sandstones up to 1600 m thick. The sandstone beds are generally flat-lying, and rest unconformably on a crystalline basement which consists mostly of granitic intrusive complexes and quartzfeldspar- biotite gneisses. The basement rocks represent Aphebian sediments and Archaean basement rocks that were metamorphosed and remobilized to varying degrees during the Hudsonian Orogeny (ca 1800 Maj.Since 1968, three mining camps and several substantial unconformity-type uranium deposits have been discovered in the area (Figs. 1 and 2). These deposits lie along the unconformity surface, partially enclosed in sandstones, and partially in the basement rocks. The major deposits have elongate, pencil shaped orebodies that are parallel to the strike of underlying graphitic biotite gneisses. The total tonnage of uranium is in the order of 150,000 to 200,000 tonnes and mining grades range from 0.5 to 2.5 per cent U3O8.IntroductionUranium exploration started in Saskatchewan in 1945 when Jolliffe and Murphy headed field parties to investigate uranium occurrences on the north shore of Lake Athabasca (Kupsch, 1978). Their investigation lead to the development of the Beaverlodge camp in the following years. Some of the early prospectors were impressed by the fact that the uranium occurrences at Beaver lodge were centred on a thick sequence of unmetamorphosed arkosic redbeds which are now called the Martin Group. This sequence was referred to as the Athabasca Series by Christie (1949), and although some occurrences of uranium were found near Stony Rapids and Black Lake, the vast expanse of Athabasca sandstones south of Lake Athabasca was generally regarded as unpromising."

Jan 1, 1986

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By L. Kilburn

A survey of 281 mineral exploration agreements examines the ratios among three ways that may be used to purchase an interest in a mineral property, viz: pay cash, pay shams and make future expenditures on the property. The dollar value of the future expenditures exceeds that of cash or shams by about nine times in most of the 110 agreements that contain cash-expenditure or share-expenditure components. Results suggest that cash and shams are treated about the same in terms of value. Buyers and sellers haw opposing priorities for the way that they prefer to purchase a mineral property. These opposing priorities should give rise to a perceived 50:50 balance between cash/share payment and future expenditures to satisfy the idealized situation described by most definitions of fair market value (FMV). This balance between cash/share payments and future expenditures appears to be rationalized in negotiations to a FMV when expenditures are nine times greater than cash and/or payments. On this basis, it is proposed that the FMV of a property may be determined by aggregating the dollar amount of the cash/share payments plus one-ninth the dollar value of future expenditures, as set forth in the respective purchase agreement, and proportionately applying such aggregate to full property value.

Nov 1, 2005

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV."

Jan 1, 2017

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d'amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d'oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d'assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d'amiante chrysotile, en vue de I'incorporer éventuellernent dans une matrice métallique. La fibre d'amiante est constituée de fib rilles élementaires d'un diamètre d'environ 0.02 um qui ont une résistance en tension de I'ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf'ort d'un matériau composite doit d'une part, avo ir des propriétés mécaniques intrinsèques élevées, et d'autre part, adhérer solidement â la matrice pour que Ie transfert de charge s'effectue sans qu'il y ait décohésion entre les composantes du matériau.La fibre d'amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l'adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu'elle est employée avec une matrice polymere. Dans Ie cas d'une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d'où l'intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d'amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By W. A. Lang

"IntroductionCARBONIZATION, gasification, and chemical utilization of coal are interrelated topics, which makes it difficult to review one without indicating its connection with the others. Hence, in Progress in Coal Technology, Series No. 5: Carbonization, reference was made to gaseous products recovered in the carbonization of coal, and .to a number of chemicals made from the tars, light oils, and ammoniacal liquors which are by-products of coal carbonization.In this, the sixth paper in the review series, prime consideration will be given to the complete gasification of coal to give a fuel for domestic industrial, or power purposes and a synthesis gas suitable for the manufacture of gasoline, Diesel oil, and chemicals. The hydrogenation of coal, an alternative source of liquid fuels and of chemicals, will be reviewed, as will be a number of processes for •the recovery of chemical products from coal by extraction and chemical treatment."

Jan 1, 1952

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025