Search Documents

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

The Kyaukpahto gold deposit is located at latitude 23¦ 47Æ 55" N and longitude 95¦ 56Æ 35" E in the Kawlin-Wuntho district, Sagaing Division, Myanmar. Gold mineralisation is hosted in sandstone of the Male Formation (Eocene) and occurs as stockworks and disseminations. The high-grade gold mineralisation is locally concentrated in a breccia zone. The gold deposit is closely associated with a NNE-SSW trending fracture system that forms tensional open fractures. These tensional zones are thought to be directly related to the Sagiang transfer fault system that experienced several hundred kilometres of northward dextral movement during the post-Upper Miocene. Major sulfide minerals are pyrite and arsenopyrite with minor galena, chalcopyrite and sphalerite. Gold mineralisation is associated with intense silicification, sericitisation and argillic alteration. Primary Type I fluid inclusions in the quartz from the mineralised zone are 5 to 15 ¦m across and yield homogenisation temperatures of 239¦ - 310¦C and salinities of 1.2 - 10.9 wt per cent NaCl equivalent. Laser Raman spectroscopic analysis indicates the presence of CO2 and CH4 in Type II fluid inclusions. Sulfur isotope analysis of disseminated pyrite in the ore zone by the laser ablation method indicates d34S values from -5.48ë to +5.53ë. The geology, alteration, ore mineralogy, fluid inclusion microthermometry and sulfur isotope data of the Kyaukpahto deposit are consistent with an epithermal ore deposit model for the deposit. However, the presence of CO2-liquid bearing fluids and the detectable CH4 in the gaseous phase of the fluid inclusions conflict with a typical epithermal origin for the Kyaukpahto deposit. The host siltstone and mudstone sequence, trace element geochemistry, and the disseminated nature of sulfide and gold mineralisation are also common characteristics of a sedimentary rock-hosted gold deposit, and these features may indicate a Carlin-like affinity. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

By Likar J, Janexic S, Zigman F

When driving mine roadways in the vicinity of tectonic disturbances and fault zones, sudden outbursts of gas, along with ejections of fine coal, occur. Substantial dynamic changes occur around the roadways in the coal and around the support. The problem has several aspects. Studies have been carried out on the technical analyses of the phenomena which occurred in the Velenje Lignite Mine from 1957 to 1988. The second part of the investigation involves systematic laboratory studies of strength and deformability characteristics of lignite samples and "in-situ" measurements of stress changes during the driving of some roadways. Analyses of events (using the model of limit convergence and the finite element method) showed the possibility of gas outbursts, taking into account the deformability conditions when crossing over from compact lignite to the disturbed region. The rate of advance of roadways and the method of support strongly influence the occurrence of the phenomenon. The preventative measures used in driving roadways under such conditions include trial drilling and the use of blasting instead of machine cutting.

Jan 1, 1992

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 µm.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By T Baard, A Pieters

This paper deals with the design and implementation of a 17 MW (nominal) surface cooling installation at Impala Platinum No 14 shaft located in Rustenburg, North West Province, South Africa.The cooling requirements included the installation of a surface ammonia refrigeration plant complete with the storage of hot and cold mine service water for underground use. It was also necessary to install a surface bulk air-cooling facility, which cools 400 kg/s of ventilation air going to the underground workings. Primary cooling is to the surface bulk air cooler. The cooling duty of a surface bulk air cooler is heavily dependent on the ambient wet-bulb temperature. Because of the daily wet-bulb temperature variation in this part of the world, use was made of a cold thermal storage facility of four million litres. The excess chilled water is stored during the night, for use by the main drilling shift during the day. This keeps the refrigeration machines as close as possible to full load during the summer, thus maximising the use of the capital expenditure. This paper discusses the control philosophy used to maximise the cooling output, as well as the thermal process. The project consisted of two phases resulting from the underground development phases of the mine. The first phase started in January 1999 and was commissioned by the end of the same year in record time. The final commissioning of the second phase took place at the end of 2002. The most difficult part of the construction phase was the tunnelling of a subsurface air duct from the bulk air cooler to the operating vertical shaft. This was done without disruption to the hoisting of men, material and ore in the shaft. Owing to the size of the refrigeration machines, the ammonia quantities involved and the application on a mine (no ammonia can go underground, either in the service water or in the mine air) special precautions had to be taken. South Africa has developed high standards for ammonia refrigeration plants used on mines, which will be partially dealt with in this paper.

Jan 1, 2005

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

This paper introduces a classification of gold orebodies, and comments on the importance of cutting high grade values, the choice of an appropriate ore reserve method and the necessity for producing recoverable ore reserves by considering the mining policy. The author stresses the importance of obtaining the appropriate information from the data relevant to a particular deposit as opposed to transfering parameters from one deposit to another.

Jan 1, 1987

By M Pizey, P Lindsay

Coal mining has been occurring on the Stockton Plateau for over 100 years. As a result of both natural conditions and mining activities, surface water on the plateau is known to have low pH and elevated metals concentrations, a condition known as acid rock drainage (ARD). Solid Energy New Zealand Ltd (SENZ), as owners of the current mining operations at Stockton desire to understand the nature and causes of ARD at Stockton to determine whether commercially viable options can be developed to improve the water quality to levels acceptable to the local community and regulators. A series of integrated water quality investigations have been performed towards developing a characterisation of the water quality on the Stockton Plateau and receiving waters. The investigations performed include: design and implementation of a water quality monitoring program to collect a satisfactory base of water quality data from which to develop an understanding of the water quality and its variability, and to collect data regarding the range of flow rates that occur in the principal streams; development of a hydrological model for the Plateau with the ability to predict flow rates at key locations on the plateau and on the Ngakawau River; field investigations of the bio-diversity of the plateau and surrounding areas, to develop a snapshot of the health of aquatic communities and whether streams draining mine workings are æadversely impactedÆ; eco-toxicology; waste dump seepage water quality monitoring at selected basal springs, drilling, investigations and permeability and geochemical testing; data processing of a range of historical data and the newly acquired data for the development of empirical relationships that describe the water chemistry system and its relationship in turn to flow rates in the streams; simulation of the long term water quality record for the measured parameters (pH, acidity and metals concentrations), based on the hydrological model and the empirical relationships developed from the new database; and preliminary development and examination of mitigation options for the ARD issues at the mine. The study has progressed towards design of pilot studies of options for mitigation of the generation of the ARD as well as treatment of the discharges. It is the integrated approach adopted by SENZ from an early time in the investigations, that has enabled fast-tracking of the pilot engineering trials. This paper presents the results of the field investigations and eco-toxicology studies and demonstrates the value of predictive modelling of water quality in the study area, even at a very early stage in the remedial engineering design process.

Jan 1, 2003

By Sibson RH

The gold province of Otago occupies an area of upwarped basement, the Otago Schist, comprising predominantly quartzofeldspathic and volcanogenic metasediments. This assemblage is the product of collisional tectonic deformation and associated metamorphism, mainly to lower greenschist facies, during the Rangitata Orogeny (200-100 Ma). Historically this region has produced 240 tonnes of gold, 4% (10 t.) of which was from the mining of Cretaceous gold- quartz mineralised vein systems. Auriferous vein systems in the Otago Schist are mainly hosted within NW trending normal fault-fracture arrays, however NW trending reverse fault-hosted vein systems also occur. We propose that the Late Cretaceous-mid Tertiary Otago Schist structure represents a regional anticlinorium containing flexural folds of at least two wavelengths. The anticlinorium structure has been quantified by determining variations in angular discordance between schistosity and the Otago Peneplain, a Late Cretaceous-mid Tertiary erosion surface covering most of the Otago district. A structural model for the evolution of the post-collisional anticlinorium requires the cooling surficial zone (carapace) of a retrograding metamorphic belt to behave as an elastic lid. Erosion of topographic load on the carapace drove isostatic uplift, which was greatest in the tectonically thickened core of the orogen. In this way differential uplift produced flexural deformation in the elastic carapace, expressed as a large scale arching of the orogenic belt. Flexure created tangential longitudinal strains in the outer-arc, leading to extension and the formation of mineralised normal faults. These structures are separated by a neutral surface from shortening and associated mineralised reverse faults in the inner-arc. Our structural model predicts that the distribution of auriferous lodes should be localised about zones of maximum flexural curvature, where the tangential longitudinal strains are highest. As a result, NW-SE hinge regions separating schistosity dip domains in the Otago gold province may have new found significance as potential exploration targets.

Jan 1, 1995

By P Pelletier, J Tessier, C Duchesne

This paper summarises research into the study of the control of flotation processes based on froth images. A review of the froth flotation operation background and the relevance and role of the froth phase are presented. The use of numerical image analysis techniques for the extraction of significant patterns from industrial flotation froths is discussed. First, the froth was analysed by the use of the multivariate image analysis (MIA) method to extract the spectral variation contained in a RBG image. The partial least squares (PLS) method was applied to develop an empirical model for the prediction of froth grade. The results of this application are illustrated using an industrial case study. Second, the froth was also analysed by grey-level co-occurrence matrix (GLCM) and wavelet transform analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths. They also provide qualitative information on the changes in the visual appearance of the froth. The pros and the cons of those methods are highlighted. Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses the reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained from the implemented control strategy are highlighted. Finally, the feasibility of implementing a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.

Jan 1, 2005

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003