Search Documents

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

By M Jones

Legacy tailings storage facilities exist within operating mine sites across Australia. These tailings storage facilities are often viewed as rehabilitation liabilities but with considered assessment may prove to be a resource. Extraction of such a resource might add value to operations by providing cash flow during the development of new mines; providing supplementary mill feed for existing mines undergoing step changes in operations; and supporting mine closure activities. Hellyer Gold Mines is successfully extracting and reprocessing sub-aqueous material from legacy tailings storage facilities at their Hellyer operation in north-west Tasmania. The Hellyer tailings storage facilities contain poly-metallic material from the Hellyer and Fossey underground deposits dating back to the 1980s as well as material from tailings reprocessing activities by other operators of the Hellyer site. Hellyer Gold Mines is reclaiming sub-aqueous material using cutter-suction dredgers and reprocessing on-site. Hellyer is the only operation of its type in Australia and few such operations exist worldwide. Key learnings around the estimation of a resource for legacy tailings storage facilities have been acquired at Hellyer that can be applied to the assessment of other tailings storage facilities. The application of dredging as a mining method at Hellyer is delivered through collaboration with experts from outside the mining industry under the direction of a mining engineer. Key elements required for the planning and delivery of safe and efficient dredging inside tailings storage facilities have been identified at Hellyer and are presented to provide a road map to the development of other dredging operations.

Sep 1, 2024

By Hatcher MI

Exploration undertaken at Copley diapir has located several occurrences of oxidized supergene and primary sulphide copper mineralization at the margin of the diapir or in adjacent country rocks. The mineraliza- tion is related to carbonate-rich epigenetic solutions which moved along major structural features closely associated with the intru sive diapir.

Jan 1, 1975

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

On Wednesday 11th November, 1970, a series of violent explosions occur-- red within No.1 Basic Oxygen Steelmak- ing (B.O.S.) furnace at the Whyalla Works of the Broken Hill Proprietary Co. Ltd., (B.H.P.) when the furnace was moved immediately prior to tapping. Water from a burnt out flux chute had flooded the bath while the furnace was tilted slightly towards the tapping side waiting to tap. Although no one was injured, dam- age in excess of $54 000 was caused to the hood and superstructure. The water hydrated the burnt dolomite refractory lining some of which sub- sequently collapsed exposing bare fur- nace shell over part of the cone.

Jan 1, 1975

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

Lake Kopiago is located some 71km northwest of Tari in the Southern Highlands Province and lies on the northern edge of the Papuan Fold Belt. The area is underlain by middle Miocene carbonate and fine grained clastic sediments intruded by late Miocene hornblende gabbros.Two mineral deposits occur to the south of Lake Kopiago. These are the Bisamu gold prospect and the Wunaki zinc-lead gossan.The Bisamu deposit consists of a calcic skarn assemblage which is geochemically anomalous in gold, silver, copper, zinc, cobalt, bismuth and tellurium. The prograde mineral assemblage includes garnet, clino-pyroxene and epidote whereas the retrograde assemblage includes epidote, quartz, actinolite and chlorite. Pyrrhotite is the dominant sulphide with minor pyrite and marcasite and trace chalcopyrite and sphalerite. Minor magnetite is also present. The Bisamu skarn shows many of the features typical of gold-skarn type mineral-isation.

Jan 1, 1994

By McBride N

Location The Boddington Gold Mine (BGM) is located approximately 120 km south east of Perth, Western Australia. (Figure 1). Located within the picturesque Darling Ranges, the land was previously used for forestry activities prior to mining commencing in mid-1987. Mineralisation is hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt.

Jan 1, 1995

Copper refining electrolytes are maintained in the range 60-65¦C to ensure an efficient operation. The heat energy required to meet these temperatures has been traditionally derived from the electrical energy required for the electrolytic process and supplementary steam energy. In 1983, experiments were conducted at Copper Refineries Pty. Ltd. (CRL) to determine the effects of insulating the Tank House cells, and fully covering the cells. The results of these experiments showed conclusively that greatly reduced steam consumption would be required to maintain electrolyte temperatures. These positive results led to an Energy Conservation Programme for the Tank House, and this was implemented in 1984. A computerised cell cover monitoring system was developed, and is used to control cell coverage and fluid balance. The experimental work and the benefits obtained since implementation of the programme are discussed.

Jan 1, 1985

By J F. C L Costa, J C. Koppe

It is recognised by the major international codes that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological and grade continuity, etc. However, the difficulty in quantifying the degree of uncertainty associated with mineral resources estimation has led to the creation of a large suite of methodologies, terms and definitions, with almost every mining company having its own set of standards. It is also intuitively known that several traditionally used methods to evaluate resources do not take into account the spatial continuity of the grades, being unable to provide a reliable measure of the error associated with their estimates. Since they do not provide an error assessment, these methods are inappropriate to assess local or global uncertainty associated with an estimate. Faced with these problems, this work aims at developing a methodology for either quantitative or qualitative analysis of mineral resources estimation, through incorporation of uncertainty and the correct definition of the associated risk or error. The proposed methodology includes the development of a software code incorporating all the main classification techniques used by the mineral industry. A comprehensive study about each technique was conducted allowing a comparison of the parameters affecting mineral inventory assessment. A case study was conducted with a typical iron ore deposit data set from the Conceitpo mine of the Itabira Complex in the Iron Quadrangle, Brazil. The results showed the specific limitations of each classification system and the influence in selecting their key parameters, always based on subjective choices.

Jan 1, 2009

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

By Ramsay WRH, Morand V

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (Dl) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with Dl and the plunge of the Fl fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late Dl. S'80 values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By Eddy B. W, Washusen J. A, Wulff R. T

The State Electricity Commission of Victoria (SECV) has been con- tinuously involved in the extraction of brown coal from open cut mines in Victoria's Latrobe Valley for over 60 years, but have not completed a major mine. Detailed consideration for rehabilitation at this stage has only been able to be given to overburden disposal areas. Increasing interest in rehabilitation in the 1980's led the SECV to review its existing policies and practices and to embark in 1985 on a public consultation process to establish an agreed and accepted policy. This was extended in 1986 to the consultation process for the rehabilitation planning for the Mor- well Open Cut External Overburden Dump. This paper covers the con- sultative process developed and the lessons learned by the participants.

Jan 1, 1989

By McKenzie C, Michaux S

Modern quarrying operations focus attention on blasting operations as a critical component in the overall cost-effectiveness of quarrying. Generally, optimisation of blasting has been linked to the processes of drilling, explosive consumption, secondary breakage, and product haulage to the primary crusher. This approach gives no consideration to the impact of primary crusher feed size distribution on downstream processes, or on the quality (ie shape and strength) of the final product. Blasting operations can be manipulated to produce a wide range of muckpile size distribution. This paper presents the results of studies into the impact of muckpile fragmentation on downstream crushing and screening operations, and includes measurements of primary blast oversize and muckpile fragmentation, together with measurements of size distribution, circulating loads and flakiness for various process streams throughout a quarry processing plant. This paper is an extension of other studies investigating the prediction and control of fragmentation from blasting, and the role of explosive performance in controlling muckpile fragmentation.

Jan 1, 1995

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

HIGHWALL MINING - DECISION TO MINEUlan had completed operations in the first Open Cut area due to high stripping ratios and the presence of geological features which destroyed a significant portion of the coal in the upper part of the seam. The pit had been abandoned in 1994 and operations had moved to a new location to the north west.

Jan 1, 1998

By F Diaz, G Hovestadt, B Friedrich, D Latacz, M Sommerfeld

The metallurgical sector significantly contributes to the global carbon footprint and encounters the challenge of developing more sustainable production methods. This study introduces novel approaches aimed at reducing CO2 emissions within the industrial sector, some of which have been developed up to the demonstration scale. In two case studies, urban waste from the agricultural sector (corn, olives, coconut etc) and waste electrical or electronic equipment (WEEE) recycling residues (shredder light fractions (SLF)) were subjected to thermal treatment. The resulting materials were then used as substitutes for conventional fossil-based reducing agents in both the copper and ferroalloy industries. Furthermore, hydrogen was employed at different scales to assess its efficacy as a reducing agent for recovering metal oxides from fayalitic copper slags. Our findings reveal promising prospects and defined specific challenges for the integration of these alternative reducing agents in the industry. The synergistic use of pyrolysed SLF, bio-coke, and hydrogen presents a viable pathway to significantly diminish CO2 emissions while simultaneously improving the sustainability of the metallurgical sector.

Jun 19, 2024

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By McKenzie C. K

During a programme of explosive performance evaluation at Hamersley Iron, Mount Tom Price Mining Operations, the relative performances of a range of heavy ANFO explosives were compared during normal production blasting operations. In addition, a number of heavily instrumented single hole blasting trials were conducted with each product type. The blasts were monitored in terms of blasthole velocity of detonation (VOD), measured using multi-point plasma conductivity probes with up to 16 measurements per blasthole. Up to 16 blastholes were monitored in each production blast. The results of measurements show a marked difference in performance of all heavy ANFO products between single blastholes and full production blasts, indicating a significant degree of interaction between blastholes in production blasting. The interaction is shown to result in a loss of detonation pressure of explosive, and considered to lead to a loss of fragmentation. The degree of interaction is seen to increase with increasing emulsion content in the products, and is more pronounced in some explosive types than others. The paper presents the methods of measurement and analysis, and the results of monitoring, together with implications on blast design and application of heavy ANFO products.

Jan 1, 1990