Search Documents

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

Elimination of zinc by the reduction of iron works dusts is examined. The process consists of blending, filtration, drying, balling, preheating and reduction in the rotary kiln. Dust slurries and dry dusts are mixed and stored in slurry basins and the blended slurry is filtered. In the balling process it is important to make green pellets which will withstand Thermal shock in the preheater and rotary kiln. Preheating to about 2000C is preferred to ensure effective use of coke fines in the blast furnace dust. The coke retained in the pellets accelerates the reduction rate. However, at the initial stage of the reduction the pellets become weakened and have to be heated slowly to prevent ring formation. In order to ensure zinc vaporization, pellets should be heated to a temperature of 1100-11500C in the kiln with injection of l ignite fines from the discharge end. Pellets having a degree of metallization of more than 90% and containing less than 0. 1% zinc have been obtained using a test kiln. The final pellet product is intended for use as blast furnace feed. A new plant with a capacity of 20, 000 tonne of dust per month is now under construct- ion and will be in operation next year.

Jan 1, 1974

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

By R G. Barker, N Mortimer

In New Zealand, platinum group metals (PGM) occur in three main geological environments of economic interest: layered mafic igneous complexes, the Dun Mountain Ophiolite Belt, and in association with placer gold deposits. Most of the layered mafic complexes with PGM potential occur in the Median Batholith. These include the Longwood (Permian), Bluff (Permian), Riwaka (Devonian) and Rotoroa (Jurassic) igneous complexes. Exploration of the Longwood Complex discovered PGM associated with gabbroic rocks. Best assays to date include a 1 m drill intersection of 1 g/t Pt + Pd and float rock with 3.0 ppm Pt and 3.3 ppm Pd. The Greenhills complex at Bluff consists of basal dunite overlain by wehrlite and gabbro. PGM occur with chrome spinel in the basal dunite and Pt geochemical anomalies have been identified associated with the wehrlite-gabbro contact zone. The Greenhills complex has some similarities to Alaskan-Ural type complexes.Reconnaissance exploration in the Dun Mountain Ophiolite Belt has identified PGM geochemical anomalies, but no follow-up work has been carried out. During the late 1800s and early 1900s, PGM were recovered as a byproduct of placer gold mining in Southland. Placer gold prospects with PGM potential include the Waiau River, deposits flanking the Longwood Complex and some Southland beaches.

Jan 1, 2002

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

By E Haren, A Winchester

The CSA Mine has a long and varied history from initial discovery in 1871 through to the present. Lead-zinc mineralisation was mined historically near the surface. Today copper and silver are extracted from the deeper regions of the mine. The mine has passed through a number of owners over this time, each with a unique operating philosophy and understanding of the mineralisation. Cobar Management Pty Ltd re-opened the mine in 1999 and has undertaken extensive drilling programs to expand the resource and gain a better understanding of the mineralisation characteristics. Presently mineralisation has been located over a strike length of 1.2 km and to a depth of over 2.0 km with over 30 mineralised lenses from four identified ore systems. The refinement of geological and mineralisation models led to further discoveries and prompted a review and modification of resource modelling processes. Advanced statistical analyses prompted the implementation of ordinary kriging as a grade estimator. Improved stationarity from enhanced geological domaining has been supported by variography and kriging neighbourhood analysis studies. Resource models at CSA are now quantifiable in terms of mineralisation style and estimation reliability. The new techniques are assisting the definition of more mining fronts, which are creating new opportunities to increase mine output.

Jan 1, 2006

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Hopkins G. M F

Intensive exploration of the Archaean ultra mafic sequence bordering the Kambalda dome has resulted in the discovery of at least ten dis- tinct areas of nickel sulphide mineralisation subsequent to the initial drill intersection in January, 1966. Sulphide ore reserves to June 30, 1972 were 19.36 million tonnes at 3.3% nickel after mining of 3.0 million tonnes at 3:7%,nickel since production commenced in March, 1967. About 75% of contained nickel metal reserves occur in sulphide concentrations located at the base of the-ultramafic sequence, in contact with underlying meta-tholeiitic basalt. The remaining reserve occurs in concentrations of sulphides within the ultramafic sequence, usually within 100 metres of the underlying contact and typically in proximity to contact mineralisation. These hanging wall orebodies are smaller, contain significantly lower con- centrations of sulphide, and generally exhibit higher Ni:S ratios than underlying contact ore- bodies. The majority of contact sulphides concentr- ations form narrow, elongate, north north-west trending bodies, closely coincident with fault bounded depressions in the contact. Detailed study of the Lunnon Shoot ore environment in- dicates that it was a locus of crustal failure during, and subsequent to, emplacement of ultra- mafic rocks. Resultant structures parallel and

Jan 1, 1973

By Denholm WT

The main objective of the experimental study was to investigate the dissolution kinetics of various forms of carbon under iron bath converting or smelting-reduction conditions, i.e., particulate, free moving carbon in contact with a turbulent iron melt. Iron/carbon melts were contained in cast magnesia-lined silicon carbide crucibles heated by a medium frequency induction furnace. The melts were stirred by injecting nitrogen through 2 mm I.D. alumina lances submerged to a depth of 50 mm in the 100 mm deep baths. Particulate carbon in the form of graphite, brown coal char and petroleum coke, were dropped directly onto the turbulent bath. The dissolution rates of the various carbon types were monitored by taking periodic bath samples for subsequent carbon analyses. The effect of carbon particle size (1-6.25 mm), the degree of bath turbulence (nitrogen stirring rates of 0-20 litres/min), and bath temperature (1300-1500¦C) were assessed. The analysis of the results was complicated by particle buoyancy effects, but it was established that the dissolution rates of the three carbon types investigated were similar, and increased linearly with increases in the gas stirring power inputs. Particle size had relatively little effect on the dissolution rates.

Jan 1, 1984

By D Stow, R Goodridge, K J. Molloy

A range of explosives has been specifically developed for soft ground blasting. These explosives can be used in both wet and dry blasting conditions, range in density from 0.3 - 1.2 g/cc and range in VoD from 2 - 4.5 km/s. This range of explosives has the potential to be tailored to ground type and is predicted to be suitable for a variety of applications which include: blasting in soft to medium overburden, coal blasting, wall control, and low vibration blasting. Trials have been conducted in several applications with encouraging results. Several cast/throw blasts have been conducted with these products partially replacing either ANFO or Heavy ANFO. The results from the blast have been equivalent in cast (per cent) and at reduced cost per unit volume. These products have also been used in presplit blasting and have again achieved equivalent or better results when compared to conventional presplit blasting at a lower cost per unit volume. This product has also been used in a vibration sensitive area replacing traditional explosive products, and generating excellent fragmentation and digging whilst maintaining vibration limits. This new range of products, NOVALITE, has shown great potential in many applications either reducing cost per unit volume, improving wall quality or improving productivity in environmentally sensitive areas.

Jan 1, 2001

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R Berry, J Hunt, T Kojovic

Geometallurgy aids the understanding of orebody variability through the integration of geological and processing information, thereby enabling spatial mapping of processing (eg comminution or separation) performance across a deposit. In order to do this, estimates of quantitative geometallurgical attributes are needed so that continuous downhole profiles can be generated for each attribute, providing vital data for the development of processing domains through geostatistical modelling. However, as traditional comminution tests are high cost and/or require large samples, current practice typically results in insufficient data density and distribution of comminution indices making it difficult to model and map deposit scale variability. The aim of this work was to find a method to estimate comminution indices based on data that is widely available at mine sites. This data includes mineralogy and chemistry of drill core samples, plus logging information such as lithology and alteration. Work to date indicates that comminution parameters such as semi-autogenous grinding (SAG) Power Index (SPI), Bond Work Index (BWI) and A*b (Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight test (DWT) Index) can be modelled using chemical and/or mineralogical data. The estimated hardness indices can then be propagated into the mine site database and used in the definition of processing domains that map inherent variability across a deposit. The estimates can thus provide geometallurgical inputs for spatial modelling, mine planning and optimisation initiatives.CITATION:Hunt, J, Kojovic, T and Berry, R, 2013. Estimating comminution indices from ore mineralogy, chemistry and drill core logging, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

THE Company's smelting equipment consists of three blast furnaces, supplied with blast from two sets of vertical piston blowers, each capable of delivering 8000 cub. ft. of air per minute at a pressure of 60 oz. per sq. in. Each blower is belt-driven by a 1:30 h.p. motor. The maximum speed of the blowing engine is 35 r.p.m.No. 1, the largest of the three blast furnaces, has a crucible area of 49.5 sq. ft., and measures 11 ft. 6 in. x 5 ft. at the tuyeres.From tapping floor to feed floor measures 35 ft. 9 in., and holds, when full, 100 tons of charge. Blast enters through thirteen 3-m. tuyeres at 60-oz. pressure. Working normally, this furnace is capable of treating :300 tons of charge, exclusive of returned slag and coke, per 24: hours, with an output of 100 tons of lead. Tapped slag flows into a C.l. forehearth mounted on wheels, where any lead and matte is caught, and the slag overflows into a 3-ton cast-iron pot, in which it is drawn away by an electric locomotive and poured over the dump.

Jan 1, 1918

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

By G Reynolds, N A. Ware, L Lu

Queensland Pacific Metals (QPM) is progressing its Townsville Energy Chemicals Hub (TECH) project to produce nickel and cobalt sulfates for advanced battery materials. Apart from the nickel and cobalt sulfates, the process also generates a hematite by-product (~640 ktpa). The hematite byproduct precipitated from the process, hereafter ‘hematite precipitate’, is high in Fe and particularly low in impurities. However, it is a fine <20 μm crystalline, hydrometallurgical precipitate and is produced as a filter cake containing a high moisture content of about 15 per cent. This is considerably different from natural hematite ore and is expected to change its performance during sintering. In the present study, laboratory scale sintering tests were undertaken to evaluate the potential impacts of substitution of the hematite precipitate for traditional magnetite concentrates and further for Australian hematite-goethite ores in a simulated industry base blend. Substitution of hematite precipitate for magnetite concentrates was found to slightly increase the sintering temperature required to achieve the strength of laboratory sinters. However, further substitution of hematite precipitate for Australian hematite-goethite ores slightly reduced the sintering temperature required to achieve the laboratory sinter strength. These results reflect the reduction in Al2O3 contents of the blends and are consistent with the trend observed in industry and pilot scale facilities. The reduction in sintering temperature generally correlates to a reduction in fuel rate in the larger scale sintering process. The pore structure of selected laboratory sinters was further examined and discussed in conjunction with sinter strength. The pore structure images highlighted the relative difference between the blends with the most obvious difference being seen at 1290°C which correlates well with the laboratory tumble index (TI). The laboratory sinter samples showed an increase in porosity and irregularity of pore shape, as hematite substitution increased demonstrating the correlation between a more porous structure and a lower TI.

Sep 18, 2023

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021