Search Documents

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

As an indication of the overall quality for the three periods the expected run of mine ashes are given. Operating Period R.O.M. Quality Years 1 - 4 22.0% Ash (db) Years 5 - 14 18.8% Ash (db) Years 15 - 20 17.3% Ash (db) The size distribution of the coal was found to be generally as predicted in the 1980 study. However the ash, particularly in the smaller fractions, was found to be higher due to the previously mentioned friable nature of contaminant material. Following evaluation of this additional information, the proposed washery design was reconsidered. Three basic process schemes were examined. 1. A jig with two-stage heavy medium cyclones and spirals for treatment of three different size ranges. 2. A heavy medium vessel, two-stage heavy medium cyclones and spirals for the different size fractions. 3. A jig for initial treatment of the total feed (that is all sizes) with single-stage heavy medium cyclones and spirals for rewashing of the intermediate and smaller size Fractions.

Jan 1, 1986

By Kapoor M. L

Emf measurements on SE galvanic cell: SS; Ni-NiO I solid electrolyte/ZrO2 + CaO I [Pb + Bi]liq alloy; (PbO); SS were made in the temperature range 913-1034 K to determine the thermodynamic properties of oxygen dissolution in liquid lead. Bismuth alloys with bismuth in the dilute concentration range of 0 to 3.08 mass per cent and oxygen in the alloy varied by equilibrating the metallic system with a suitable (PbO) slag. Wagner's interaction parameter approach was used to calculate the ternary interaction parameter, eBiO at temperatures of 913, 953 and 993 and 1034 K and to observe the temperature dependence eBiO = 19 200/T - 17.454. Quasichemical fonnulation was employed to yield lnf BiO and reveal the effect of bismuth on oxygen in lead. The results obtained are discussed on the basis of theoretical models and the value of Wagner's energy parameter 'h' estimated to predict the results in a Pb-Bi-O system.

Jan 1, 1995

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

By Onal G, Celik MS, Dogan MZ

Chromite tailings assaying 21.2 per cent Cr2O3 was upgraded to 48.7 per cent Cr2O3 at a recovery of 72.0 per cent using column flotation with a mixture of anionic collectors at pH 11. Electrokinetic methods were used to elucidate the mechanism of collector adsorption and correlate the findings with the optimum flotation conditions. Multivalent constituent ions such as Cr3+, A13+, Fe2+ and Mg2+ were found to adsorb on chromite surface and shift the zpc of chromite in the direction of oxide form of the mineral. The anionic collectors also imparted a negative charge to chromite in the entire pH region. The higher zeta potentials obtained upon adding the anionic collectors is ascribed to the adsorption of anionic surfactant onto the positively charged chromite surface. The positive sites are generated through formation of significant amount of hydroxy complexes of magnesium at pH 11. Complementary infrared data reveal the absence of a shift in the spectra indicating the possibility of physical adsorption in the system.

Jan 1, 1993

During the intial two years (1972 - 1974) of exploration at Telfer, water require- ments were limited to supporting a 50 man camp and diamond drilling to verify thickness and grade of the stratabound ore deposit. Water bores were drilled to intersect the Middle Vale Reef down dip from its outcrop about 70 metres below surface. The MVR reef is an oxidized pyritic horizon which contains 30% - 65% sulphide below the zone of oxidation and forms a highly porous leached gossanous zone to a depth of 100 metres. Surface run-off water from the low hills associated with the Main Dome structure have led to annual re- charge of this extensive aquifer which MAP AREA Lake Waukarlyearly Permian rocks Precambrian basement - - ~;; rocks Sand d.n.s pò. _ « Drainage sg 1 qo~ (`-~.~ ? ò;+ Palaeochannel and 1 d {- subsurface drainage % GLENN BOREFIELD PASSMORE FAULT ;òTsI1. G-OId MIns BOUNDARY oChr~st as t .` Pool 4, 1 j`` Lake Dora òt ~daN 22' 0, 50 Niter KILOMETRES Fig 1. Telfer district map, Great Sandy Desert, Western Australia.

Jan 1, 1988

This paper reports on the field results of using electronic detonators to improve blast outcomes. OricaÆs electronic detonator, the i-konTM Digital Energy Control System, allows exact and precise timing in 1 ms increments from 0 to 15 000 ms. This gives the blast engineer and shotfirer the ability to fire a blast using any possible desired sequence. In the three years that have followed the release of the i-konTM System, Orica has been re-exploring ways of initiating blasts using the abilities of electronic detonators to improve fragmentation, diggability and crusher throughput. This study began with revisiting fundamental blast theory, lead to generation of new state of the art computer fragmentation modelling and ended with many iterative field trials of i-konTM blasts across a wide selection of mining methods and rock types. At three sites a detailed measurement process was undertaken to compare the results of pyrotechnic blasts with i-konTM blasts. This paper will detail the significant improvements in fragmentation, diggability and crusher throughput that was found at these sites.

Jan 1, 2003

By C O. Gomez

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

By Lewis IE

Copper-lead dross is a by-product of the refining of lead bullion produced by the Imper- ial Smelting Process. This dross contains some 27 percent copper, 50 percent lead, four percent zinc and one percent sulphur. An ammonium carb- onate leach at atmospheric temperature and pressure removed the copper from the dross while the lead zinc and precious metals remained in the leach residue for return to the smelter. The leach solution containing the copper was then purified by liquid-liquid ion exchange using LIX64N in a kerosene diluent. ("LIX" is the registered trade mark of a range of hydroxy oximes marketed by General Mills Inc.) The pilot plant had a capacity of 0.7 kg/h of CuSO4,5H20 and was operated for some fifty days on a two shift basis. Copper sulphate of excellent purity was produced, and the results obtained indicated that a copper recovery of ninety percent from the dross could be expected from a commercial installation.

Jan 1, 1975

By G J. Sparrow, M J. Fisher-White

A mineral and chemical characterisation study was conducted on ilmenite-rich heavy mineral concentrates sourced from the western sector of the Eucla Basin in southern Australia. Test work involved using X-ray diffraction (XRD), scanning electron microscope (SEM) and electron microprobe-based characterisation methods. Results showed considerable variability in the degree of ilmenite alteration between deposits with TiO2 contents varying from 53 - 63 wt per cent TiO2. Notwithstanding variability between individual deposits, the samples all had [Ti]/[Ti+Fe] ratios >0.5 consistent with a mineral assemblage of hydrated ilmenite or the hydrated, Ti-rich alteration phase pseudorutile (Fe3+2-x Ti3O9-3x (OH)3x). Accessory phases consisted of rutile (primary and secondary), zircon, aluminosilicates, quartz, Fe oxyhydroxides and spinels. Results for the most altered material are broadly comparable with data for ilmenite concentrates from the eastern margin of the basin. The mineralogy of the western Eucla Basin concentrates and the minor element composition of the ilmenite grains suggest they could be upgraded to synthetic rutile by a modified Becher process.

Jan 1, 2008

By Liu H, Chen S

Natroalunite is one of colouring minerals in kaolin. In this investigation, natroalunite, on which Ca(II) was adsorbed, was flocculated by HPAM and kaolin was depressed in suspension. The adsorption of Ca(II) on the natroalunite surface was studied by zeta-potential measurement and Auger Electron Spectroscopy analysis. Ca(II) was adsorbed more on the natroalunite surface than on the kaolin surface. The mechanism of Ca(II) adsorption was considered to be chemical adsorption on natroalunite and to be physical adsorption on kaolin. It has been found that Na6P6O18 and Na2Si04 can strongly affect Ca(II) adsorption on the surface of kaolin, but weakly on the surface of natroalunite. The effects of degree of hydrolysis and the molecular weight of HPAM, the effect of pH and the effect of Ca(II) have been studied. The kaolin ore, containing SO3 1.05 per cent has been processed with this method. The products only containing S03 0.36 per cent and the weight ratio of concentrate 52.27 per cent were Obtained.

Jan 1, 1993

From December 1994 to November 1997 Odin MiningÆs Estero Hondo alluvial gold mine in western Ecuador washed almost 3.2 million bank cubic metres of gravel to produce just over 2600 kilograms of pure gold at a recovered grade of about 0.8 grams per bank cubic metre. The operation was a simple open pit. Draglines stripped the overburden, backhoes mined the gravel, and trucks transported the ore to a stationary, gravity-based wash plant for processing. At start-up the planned throughput was 55 000 bank cubic metres/month, but a year later this had been increased to 100 000 bank cubic metres/month. From April 1993 to July 1997 a total of 440 churn drill holes and 15 pits were sunk to test the property. The methods used to prepare the resource and reserve estimates from the raw field data are described, and seven sets of completed estimates are used to track the evolution of the projectÆs resource/reserve base through the exploration, feasibility and production stages.

Jan 1, 2003

By J I Stewart

The Copper Canyon deposits, occur in proximity to the regionally distinctive formational boundary between the Staveley Formation and Marimo Shale. The mineralisation here is associated with breccias, veins, and alteration zones near the base of the Marimo Shale unit and in the underlying evaporitic dolomite-dololutite dominant Staveley Formation. The Marimo Shale unit, in its basal 60 metres, is highly carbonaceous and hosts ubiquitous but minor diagenetic (?) copper-pyrite, and on occasion, extensive albite-microcline alteration centres, pyritic (cobaltiferous)-quartz veins, and microcline-quartz_+plagioclase veins or veinlet arrays. The most significant mineralisation, such as at the Greenrnount prospect, consists of a shallowly dipping package of alteration zones overprinted by multiple generations of pink-orange microcline-quartz-chalcopyrite-pyrite-(arsenopyrite) and albite-calcite- phlogopite veins. Accessory mineralogies in most of these mineralisation styles consist of tourmaline, monazite, rutile, and apatite. Chalcopyrite (and secondary chalcocite) and gold are associated with each generation of alteration but are best developed in the later stages of veining. In the underlying Staveley Formation, which is a conformable transition between the Corella Formation limestones and the Marimo Shale, chalcopyrite (cobaltiferous)-pyrite mineralisation occurs as disseminations in pre- and syntectonic breccias, and with disaggregated silica pseudomorphs (after thinly bedded evaporitic sulphate beds) and associated dolomitised limestone-calcilutite. Although this mineralisation may be partly diagenetic in origin the 200 in thick evaporitic packages are also host to a locally widespread (2 to 4 km long and 200 to >500 metres wide) and pervasive 'redrock' styled microcline-dolomite¦hematite alteration. Within this gross alteration package there also seems to be a consistent association with narrow (10 to 100 metres wide), linear (stratabound) semi-massive magnetite-hematite-microcline and quartz-chalcedony replacement zones. Like much of the nearby Corella Formation the Staveley Formation, under the Marimo Shale, has undergone dissolution, paleo-solution karsting (breccias) and tectonic brecciation such that the precursor lithological details have been progressively obliterated. The post-diagenetic to post-tectonic fluid pathway development and metasomatic alteration history of this important lithostructural package of rocks has been traced from preliminary studies only. The ability to do so is largely due to the absence of significant regional and contact metamorphic overprinting, and the local preservation of precursor sediment profiles. It is proposed that both the base of the Marimo Shale and parts of the underlying evaporitic-limestone-dololutite have acted as conformable fluid pathways for hydrothermal and (perhaps) diagenetically derived, Cu-Au-(¦Co ¦As) K-Na-Ti-REE bearing, fluids and brines.

Jan 1, 1994

By B McFadyen, Y Potvin, K Woodward

The Australian Centre for Geomechanics (ACG) held two workshops in 2019—one in Australia and one in Canada—to discuss processes and methods currently used in the mining industry for stope design and reconciliation. In practice, this work strives to optimise stope performance and aims to maximise ore recovery (minimise underbreak), while minimising dilution (overbreak). One of the key findings from the workshops was that current stope design practices, almost exclusively, rely on some versions of the empirical Stability Graph methods developed in 1980s. Although robust and useful at the feasibility study stage, there are a number of inherent shortcomings with this approach. The Stability Graph’s limitations first lie in that it cannot assess underbreak, which is a very important measure of performance. Furthermore, the method doesn’t consider a number of factors which often have a critical influence on stope stability, for example, drilling and blasting or the presence of faults. Given the current industry standard practice, there is a great opportunity to reinvent the stope design process to optimise performance. A finding of the workshops was that every mine quantifies stope performance in terms of volume reconciliation with a focus on dilution and ore losses, and reconciling metal tonnes recovered from the mill. Many mines further investigate stope performance by looking at individual stope faces and the causes for the deviations between the planned stope shape and the measured cavity. Recent research at the ACG has shown that investigating overbreak and underbreak at a higher resolution is a powerful way to identify the root causes of overbreak and underbreak. Finer scale assessment is achieved using an octree analyses, which effectively divides the relevant stope volume into cubes on the scale of a metre and produces many tens of thousands of data points. The octree data structure and subsequent analysis underpins a data-driven stope design methodology. The ACG is currently developing a design approach based on multivariate modelling methods that can account for the many variables that influence stope performance and forecast stope overbreak and underbreak results. Back-analysing stopes based on octree reconciliation results provides a rich database for training the model. Once the model can achieve reliable forecasting of overbreak and underbreak, an interactive drill-and-blast design will allow for the assessment of different firing strategies to optimise stope performance.

Mar 15, 2021

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By K Sanematsu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore deposits of rare earth elements (REE) in South-East Asia are classified into four types: carbonatite, allanite, ion-adsorption and placer. Occurrences of the carbonatite deposits are confined almost exclusively to the Red River Fault Zone of northern Vietnam. Since the carbonatites contain dominantly REE fluorocarbonates (eg bastnasite) and lesser amounts of monazite, they are rich in light REE but poor in heavy REE. The ion-adsorption type deposits and prospects were found in Myanmar, Vietnam and Thailand. The ion-adsorption ores generally show lower REE grades than those of the carbonatite type and placer deposits; however, they could be enriched in HREE, which are more precious and scarce commodities than LREE. The ores consist of weathered granites with a significant amount of ion-exchangeable REE, which are extracted by using a dilute electrolyte solution. The ion-exchangeable REE are likely to be sourced from REE fluorocarbonates, allanite and titanite because these minerals are relatively susceptible to weathering and release REE3+ ions into soil water. In contrast, monazite and xenotime are resistant to chemical weathering and could form placer ores. Placer monazite and xenotime have been processed as by-products of placer Sn, Zr or Ti in Malaysia, Thailand and Indonesia, although the current production is small.CITATION:Sanematsu, K, 2015. Rare earth element deposits and prospective areas in South-East Asia, in Proceedings PACRIM 2015 Congress, pp 671–678 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015