Search Documents

By R Fleming, G Jones

An ocean outfall is currently under construction in Christchurch, New Zealand to transfer treated wastewater from the existing treatment ponds at the city wastewater treatment plant to diffusers located 3 km offshore. The New Zealand $85 million project comprises a new pump station and 5 km of 1800 mm diameter pipeline with a design capacity of 6.0 cumecs. The pipeline comprises 2.3 km of concrete pipe installed by microtunnelling and 2.7 km of polyethene marine pipe installed by dredge and lay. This paper describes the consent process, key environmental and community constraints, the tender process, risk provisions included in the contract, the type of contract, partnering provisions, geotechnical design issues and the pipejacking construction activities and issues.

Jan 1, 2008

By Q Xin, X Shengming, C RuÆan, Z Zhigeng a

The optimum defluorinating conditions for Sichuan bastnasite crude ore were determined by orthogonal experiments. Over 95 per cent fluorine in the crude ore was stripped by roasting 30 minutes of the crude ore with Na2CO3/ore =0.25 at 650oC. The stripped fluorine crude ore was further treated by NH4 Cl to recover rare earth. Above 95 per cent rare earth can be leached by water after the stripped fluorine crude ore mixed NH4Cl(NH4Cl/ore =1:1) roasted 1 h at 325oC. At the same time, the rare earth leaching solution contains little Fe, Si and Al. Therefore it is propitious to further purify the solution and recover rare earth.

Jan 1, 2000

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Floyd JM, Richardson P

The extension of theoretical and laboratory studies of the roasting of tantalite and cassiterite concentrates from Greenbushes Tin Limited to pilot and semi- commercial plant developments is detailed. A rotary pilot furnace was used to prove the feasibility of the process and a semi- commercial plant was constructed at Greenbushes to produce large quantities of roasted calcine. The additions and conditions of the laboratory study were employed to achieve marketable grades of calcine from the two materials. As well as producing calcines with less than 0.1% Sb, most of the tin in tantalite was recoverable to a separate fume product. Tin fumed during cassiterite roasting on a semi-commerical scale amounted to less than 1% of the tin in feed.

Jan 1, 1986

By Warren R. P

When the original Mount Gunson joint venture, between CSR and United Uranium ceased operations in December 1971, an intensive ex- ploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the discovery of the Cattle Grid deposit. A comprehensive sampling programme proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu, calculated at a 1.0% Cu cut-off. The planning and development programme that followed this discovery included not only the mining and metallurgical aspects of the exploration of the deposit, but also the en- vironmental aspects. Preliminary work included data collection with respect to meteorology, soil types, and existing flora and fauna.

Jan 1, 1976

By Ciminelli VST

Thiourea leaching has been applied to a refractory gold concentrate previously treated by bacterial oxidation. Following the bio-oxidation, gold has been leached in acidic thiourea solutions, under different pH(1 - 2.4), thiourea concentrations (2 - 15 g/1), ferric ion concentrations (0.04 - 3 g/1) and temperatures (298 - 333 K). Through this procedure, it was possible to increase gold extraction from 40 to 77 per cent. The increase in temperature raised gold extraction and reduced reagent consumption. Sodium sulphite addition was also very effective in lowering thiourea consumption. Staged leaching operations with interstage acid washing and carbon-in-leach experiments were tested, in an attempt to increase gold extraction. The results of thiourea leaching were compared with those obtained with cyanidation.

Jan 1, 1993

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By S Thomas, S Ricketts, R Hassell

Northern Star Resources (NSR) operates several operations utilising narrow vein stoping operations in the Kundana area. Stope dilution performance is variable across these operations, with unplanned dilution reducing individual stope economic viability, increasing risk to personnel and machinery operating in and around the stope and delaying the overall stoping sequence. Technical investigations were undertaken to objectively understand the variables which had the largest impact on stope performance and then use the findings to help develop mining strategies to reduce dilution. A stope reconciliation process was developed to compile key stope performance information such as stope design parameters, geotechnical and drill and blast factors. These were compared against the measured dilution. Production targets necessitated a high turnover of stopes in the operations, and hence a requirement for an expeditious process and mine design software with automated tools. The output of these results, together with numerical variables from geological, geotechnical and drill and blast data were analysed via multivariate regression. The analysis identified the factors with the greatest influence over stope dilution, and a forecast model was consequently created. Confidence was gained in the model when the subsequent stopes performed in line with prediction. Different drill and blast designs were subsequently trialled and found to reduce dilution. The model was then updated with the new practices, facilitating further regression analysis to identify revised key controlling factors. The subsequent production results however, displayed a poor correlation with the prediction from the revised model. Inconsistencies in drill and blast designs and execution were identified as key factors in the dilution performance. This was an important finding as the correct implementation of the design is critical and this has become a key focus for future stoping. Overall the technique presents an objective process to identify causal factors of stope dilution resulting in improved economic metrics for stope production. The process will be applied to other similar Northern Star operations.

Mar 15, 2021

By G Pasin, F Wirfiyata, G Khomaeni, W Valery, A Maclean, A Jankovic

The grinding circuit at PT Newmont Nusa Tenggara (PTNNT) – Batu Hijau mine consists of two SABC (semi-autogenous milling, ball milling, pebble crushing) trains, including four 20'?×?33'6? ball mills that have been lined with steel liners since the commissioning of the plant in 1999. During 2011 and 2012 an industrial trial was conducted to evaluate Poly-Met liners (a combination of rubber and steel liners). These new liners were installed in two of the ball mills (ball mills 1 and 2) and operated in parallel with ball mills 3 and 4 with steel liners.The objective of the trial was to compare the plant performance with the Poly-Met and steel ball?mill liners with regards to wear life, mill throughput, grind size and total unit costs. The trial was conducted over the entire life of the liners. The evaluation methodology implemented consisted of frequent spot sampling around the ball mill circuits, complete surveys/audits in both ball mills, and detailed analysis of process data. This paper presents the results of the industrial trial and main conclusions.CITATION:Maclean, A, Wirfiyata, F, Khomaeni, G, Jankovic, A, Pasin, G and Valery, W, 2014. Ball mill Poly-Met liner evaluation at PT Newmont Nusa Tenggara – Batu Hijau mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A E. Petts

Record iron ore prices and a renaissance of infrastructure in the Pilbara have Flinders Mines poised to move from explorer/developer to an iron ore producer. The potential of the company’s Pilbara Iron Ore Project was first highlighted by the announcement of Rio Tinto’s Caliwingina North deposit to the north and the Fortescue Metals group’s Serenity deposit in the southeast. The success of Flinders Mines’ exploration has been based on incorporating landscape studies into an existing geological framework, and using this to understand the iron-rich materials that were emplaced during the Tertiary. The development of the Delta and Eagle deposit resource models highlights this process. There are three main mineralisation styles at the project; detrital iron, channel iron and bedded iron deposits. They have textural and mineralogical similarities with comparative deposits in the region. Gaining an insight into the geological processes unique to detrital iron deposits and more distal channel iron deposits has been important to understanding the geometallurgy of the mineralisation. The model sits comfortably with other regional oregenesis models and allows a contextual framework to be developed around the timing of deposition of the Fe-rich detritus and pisolitic nodules that dominate the deposits. The exploration model also allows Flinders to explore more effectively for bedded iron mineralisation developed prior to, and since the development of the Tertiary weathering landscape.

Jul 11, 2011

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By A Penney, M J. Pascoe, R M. Stephenson

The empirical McCracken and Stacey stability and risk assessment method has been in use for more than 20 years to assess geotechnical stability issues for raise bored shafts. The methodology has been applied with various levels of success. Increasingly, trends in mining and civil tunnelling have been towards larger diameter, single pass, raise bored shafts to rapidly provide means of ventilation, material movement (ore passes), or emergency egress. Identifying and assessing potentially problematic zones before raise boring commences can allow for appropriate risk-based decisions on construction, or to investigate alternative solutions. The implementation of a proactive solution to raising through an identified weak zone is preferred to the application of an engineered solution to an area subjected to substantial instability or failure. Methods for investigating potentially problematic areas are discussed in this paper based on AMC’s benchmarking data. Proactive investigation programmes resulting from these investigations are also discussed. Previous publications discussing the benchmarking data have concentrated on Australian case studies. Increased efforts and recent updates have been made to expand the database to include international case studies. This has provided further refinement of lower bound ‘raise bore rock quality index’ (QR) values, and various rock mass parameters for stability assessments. CITATION:Penney, A, Stephenson, R M and Pascoe, M J, 2018. Raise bore stability and risk assessment empirical database update, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 434–445 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By M Wagner, H Assimi, F Neumann, C Garcia, B Koch

Run-of-Mine (ROM) stockpiles are the inventory of valuable materials extracted from the mine. Depending on the customer requests, a selective addition of ore from stockyards should be selected at the required tonnage. In the stockyard, stackers and reclaimers are the machines which load and unload ore, respectively. Currently, humans determine the reclaiming/stacking planning sequence in the stockyard by rules of thumb. However, this is a complex task subject to multiple operational constraints, such as where undesirable mineral properties should not exceed certain limits in a request. Human planning can lead to limited decision support and lower ability to consider the upcoming blends and requests. This kind of decision making can cause perturbations in the assumed profit and unexpected loss in practice. Therefore, an intelligent decision-maker and sequence planner would be highly valuable to automate stacking and reclaiming operations in practice. The benefits are reducing variability in decision-making and operation costs. This paper considers a stockyard with available mineral information in the stockpiles using load and dump locations from GPS data feeds. We present an optimisation problem to find a solution which results in reclaiming more ore in a shorter time. To solve the problem, we develop an automatic search strategy based on the greedy search algorithm independent of the type of machine used in reclaiming. The proposed method plans a sequence for stockyard recovery blend optimisation to meet multiple customer demands in a timeframe. Blend optimisation is subject to various constraints such as the elemental composition of the valuable materials and penalty elements. We present three case studies using EKA’s simulator, to fulfil two to four requests from four stockpiles. We compare the obtained results with a pilgrim step reclaiming heuristic and we show how our proposed search strategy outperforms the current strategy used in practice.

Nov 10, 2020

By J King, T Hunter, R Coleman

"The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.Trends amongst service providers will be put forward as well as developing options and alternatives. These embrace a whole gamut of agile alternatives in the areas of partnering, alliances, commercial and shared risk models and mutual innovations. These will be discussed with some case studies and suggested approaches.Particular emphasis will be upon brownfield expansions and upgrades which have emerged recently as a preferred lower capital and focused way to achieve best practical outcome at lowest cost. There are a number of specific features of such brownfields projects including the requirement for very close cooperation between the execution team, operators, maintenance and suppliers and a maximum usage of site resources and ingenuity. Often, required investment hurdle rates are high, downtime allowed is minimal and site resources usage is maximised. This requires mutual trust, good planning and high health, safety, environment and community (HSEC) standards and practice. In many ways the practices and skills needed are the exact opposite of the historical ‘big greenfields’ project with which the industry has been geared for more recently.Another developing area has been with innovative commercial models and practices. These have been as a direct result of the more challenging investment criteria being adopted and the relative hunger of service providers. It has become more common to look at these commercial/costing alternatives very early in the project cycle as an essential project tool and not just as a possible option. These commercial solutions cover such alternatives as leasing and rental, deferred payments, build–own–operate–transfer (BOOT) and build–own–operate (BOO), whole-of-mine preferred spares and maintenance terms, and aggressive performance targets with real assurance penalties. Once again this requires very close mutual dealings and trust, and sufficient time allocation compared to a conventional approach.Citation:Coleman, R, King, J and Hunter, T, 2016. Upgrades, Modernisations and Expansions... Where Will the Expertise, Capability and Skills Come from in the Future?, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011