Search Documents

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The current talk of risk management as a separate discipline and management function is like earlier imposition of Quality Control (QC) as an overlay on shoddy production management. Risk management is vital, but is integral in the way we marshal our staff, make decisions, then monitor and review and make crucial secondary decisions. New leaders must not assume that hiring experts ensures good decisions. It is only the essential step one. The worst company I worked for had more expertise than the best. The difference was in culture and decision-making processes. Failed feasibility studies, persistent technical factions in a company that cancel each other, heaps of expert consultant reports piled up like a dump of bricks, even great but half-managers in large and small companies cancelling expertise at their disposal, are the worst manifestations. Just daily foul-ups are common even amongst smart people. We miners have made a great industry but are content to drift far below excellence, even where that word is bandied around. All the management literature and management courses will not right the situation û we have been sending budding managers to this good stuff for two generations and the effects are worthwhile but marginal. A few key ideals, ideas and slogans are not the way. These make inspiring books that work about as long as the Christmas spirit does in the real world. What we need is a coachesÆ manual and a standard of the essential package of culture and work processes that make excellence possible and show how to maintain it long term. It has not been written until now because most managers want to remain dilettante amateur managers without the discipline that creates excellence. First, believe excellence is possible and worth any effort; then commit to it.

Jan 1, 2007

By D Hunter, N Cusworth, J Miller

"Recent project failures have called into question the use and relevance of benchmarking and independent reviews, forcing a rethink of traditional processes and procedures.With cost estimates and schedules dramatically varying from lows seen around the global financial crisis to peaks experienced in the recent mining boom, benchmarking has ranged between essential and misleading.Profound shifts are now underway in future project delivery strategies as the market moves away from cost-plus engineering, procurement and construction management. The current trends in project implementation are to utilise more lump-sum design and construct or fixed-price supply and construct contracts. This trend will remove transparency in detailed cost information by reducing the sources and clarity of cost data.Independent peer reviews (IPRs) of studies and investment recommendations performed over the last decade have both failed to prevent flawed or deficient projects from proceeding to approval and funding, and been successful in ensuring that owners did not proceed with doomed investments.In recent times, it has been recognised by some owners, contractors and engineers that traditional benchmarking checks or IPRs, or a combination of both, will not necessarily produce reliable assessments of study conclusions and of the forecasts of project outcomes. To be of value, the benchmarking process now also needs to recognise the highly volatile responses from the engineering and construction industry to the current and future markets for their services.Similarly, reviewers who draw upon benchmarks of past project experiences on an understanding of the things that shaped and influenced their outcomes need to be more aware of how a future dynamic market may impact the outcome of the projects and raise warning flags accordingly.With the commodity cycle currently approaching what is hoped is its bottom, ensuring that benchmarking and independent reviews evolve into reliable, transparent and worthwhile processes becomes even more important. This can only be achieved with more transparent and analytical benchmarking and business-orientated reviews that both recognise and calculate the impacts of dynamic markets on project implementation.CITATION:Cusworth, N, Hunter, D and Miller, J, 2016. The role of benchmarking and independent reviews, in Proceedings Project Evaluation 2016, pp 249–259 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By J Jeffery, P G. Knott, F Velge, C Evans

A trigger action response plan (TARP) provides a structured response to escalating levels of risk. In mining, TARPs are typically applied to primary hazards such as inrush, strata failure or heating. Necessary for the creation and deployment of a TARP is a monitoring system capable of detecting deviations from normal conditions. The advent of real-time instruments capable of measuring diesel particulate matter now permit decision-making within shifts to address possible overexposure. Deploying a TARP for diesel exhaust emissions can lower the probability of a person’s average exposure (over a full shift) exceeding the exposure standard by detecting deviations of diesel particulate concentrations from normal conditions. This enables pre-emptive action to mitigate or protect. Another goal is to drive ambient air concentrations lower through the application of corrective actions as a result of instances where concentrations exceed ‘normal’.CITATION:Knott, P G, Evans, C, Velge, F and Jeffery, J, 2015. Trigger action response plans for diesel exhaust exposures, in Proceedings The Australian Mine Ventilation Conference, pp 129–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Horeth, E Duggan, B Versiani, A Gooch

Iron ore screening plant productivity is strongly affected by the performance of the shuttle operation, with the control system robustness and associated strategies having a direct impact on utilisation and throughput rates. A number of aspects intrinsic to the methods and technologies traditionally applied on the motion control of shuttles are often observed to decrease the efficiency of the ore distribution process across multiple screening modules, which ultimately impacts the plant’s production. Those include the number of operational scenarios that are unmanaged by conventional discrete control logics which may intermittently lead to undesired events, such as ‘high level alarms’ and ‘low level interlocks’ in the screening bins. This outcome usually demands excessive manual intervention by Control Room Operators. A Reinforcement Learning (RL) Artificial Intelligence (AI) solution was deployed to control the motion operation of the scalping and products screening shuttles in an iron ore handling plant. The RL algorithm was trained in advance to handle multiple operational scenarios and generate optimised outputs. In nominal operation, the shuttles are moved in a modulating and highly predictive fashion over the whole range of safely reachable bins. When the need occurs, the AI control agent deviates from that modulation behaviour, limiting its travel range or moving to other groups or clusters of available bins by employing ‘bin jumping’ or ‘ore break’ strategies. The RL platform capabilities include the ability to learn in real time to account for and auto-adapt to new operational patterns and process changes whilst applying improved strategies for shuttle dwelling times, target setting and speed control. The deployed Reinforcement Learning AI solution has better managed the existing challenges associated with the shuttle operation and control, and resulted in a more efficient ore delivery process, superior operations stability and increased production rates.

Nov 8, 2021

By Gomm SA

The Mount Tom Price Concentrator, which contains a heavy medium cyclone plant for beneficiation of the -6+0.5mm fraction of low grade iron ore, is described. Testwork was carried out on an opportune basis over a period exceeding twelve months, to evaluate the separation performance of the heavy medium cyclones. Plastic density tracers were used and ore samples were taken and analysed. The effect of operating medium specific gravity (S.G.) on the separation parameters, the iron grade of the sinks product, and the mass and iron recoveries were investigated. Also examined were the differences in perform- ance between particles of different size. The implications of the findings for plant oper- ation are discussed.

Jan 1, 1987

By M W. I Visser Æt Hooft, R C. Schimmel

Until recently the Corus IJmuiden pellet plant produced approximately 4.5 Mtpa of pellets. Corus IJmuiden is currently running a program to increase its pig iron production to 6.4 million tonnes HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50 per cent high basicity sinter and 50 per cent acid pellets, both produced in-house. To accommodate the increased pig iron production, the capacity of the pellet plant needed to be increased to 5.0 Mtpa. The productivity was increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

Jan 1, 2007

South Crofty's ventilation network is large and complex. Of the total exhaust air quantity 40% enters the mine by leakage routes through old workings, this air carries high concentrations of radon gas and results in the mine becoming a classified work place under the Ionising Radiation Regulations 1985. Improvements in the control of the ventilating air and dilution by increased air quantity have reduced the average contamination to aelow-0.2 WL. The major part of the radon originates from ground water inflows and from concentrations of radium within the mine with direct emanation from rock surfaces being negligible. Of 600 kBgs-1 total radon leaving the mine 93% cannot be accounted for from known and accessible sources.

Jan 1, 1988

Samples weighing 0·5 g are fused with sodium hydrogen sulphate, leached with 5 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is boiled with concentrated nitric acid and then 2 ml. of a phosphotungstate solution are added. After dilution to 10 ml. with water, the solution is heated in a boiling water-bath for not less than 10 min. When cold, the solution is extracted with 2 ml. of iso-amyl alcohol and the yellow phosphotungstovanadate complex is compared with a standard series. Concentrations down to 4 p.p.m. may be analysed at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By K L. Brown

The concentrations of trace metals in deep hydrothermal solutions (~1 km depth, 200 to >300¦C) from modern hydrothermal systems in the Taupo Volcanic Zone, New Zealand, and Ladolam, Lihir Island, Papua New Guinea were obtained using a purpose-built downhole fluid sampler and ICP-MS analyses. The results range widely: gold (<0.1 - 23 ppb); silver (<3 - 2400 ppb); arsenic (100 - 18 000 ppm); antimony (2 - 1200 ppm); mercury (<1 - 78 ppb) and provide the basis for quantifying the flux and fate of metals as well as assessing their sources (Simmons and Brown, 2006, 2007). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Y Wu, F-J Ping

Today, coal production accounts for about 65 per cent of the nationÆs gross energy in China. By the year 2010, the output of coal is planned to increase to 1.65 billion tonnes and by the year 2020 to 1.9 - 2.0 billion tonnes. To meet these energy needs the Chinese coal industry is developing underground coal production on a massive scale. The new drive introduced by using direct torque control (DTC) is now proven technology for mine shaft hoisting. The drive offers unequalled speed and torque control performance as well as a low impact on the supply network by controlling the power factor to unity with a minimum of harmonics distortion.

Jan 1, 2005

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By J Fewings, T McCredden, S Seet, C Fitzmaurice

"Flotation of nickel sulfide ores are generally constrained by nickel grade and impurity concentrations (notably magnesium and arsenic) in the product delivered to smelters. Being a physical separation process, flotation recoveries and grades are limited by the grade recovery curve of a particular operation, where increasing product grades are invariably associated with lower recoveries. Impurities put further pressure on this relationship, as removal of impurities from the final concentrate is almost always associated with nickel losses.Western Areas Ltd are developing a proposed expansion to its Cosmic Boy concentrator to treat an impurity stream, that is high in nickel and would otherwise report to tails. Through the use of BioHeap® technology Western Areas aims to recover the nickel and discard the arsenic to tailings. This expansion will consist of a biohydrometallurgical plant that leaches the nickel arsenic minerals, removing the arsenic as a stable iron/arsenic hydroxide, while recovering the nickel as a high-grade nickel sulfide product (at approximately 50 per cent nickel). This can then be blended with final concentrate to improve nickel grades and recoveries, while simultaneously reducing impurity levels or used to produce high value products like nickel sulfate.The introduction of a small microbial leach plant may be beneficial to base metal concentrators constrained by impurities or grade.Citation:Fewings, J, Seet, S, McCredden, T and Fitzmaurice, C, 2016. BioHeap® - Breaking the Grade/Recovery Curve for Nickel Concentrators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By P F. Hodkiewicz, J de Lacey, M Stewart, R Lane

"Implicit modelling is an approach to spatial modelling in which the distribution of a target variable is described by a unique mathematical function that is derived directly from the underlying data and high-level parametric controls specified by the user. This modelling approach may be applied to discrete variables such as lithology (after converting the discrete codes to numeric values) or to continuous variables such as geochemical grades. This paper discusses the estimation of continuous (grade) variables using implicit modelling.One of the underlying engines of implicit modelling for producing this mathematical function description is the radial basis function (RBF). In essence, the RBF is a weighted sum of functions positioned on each data point. A system of linear equations is solved to derive weights and the coefficients of any underlying drift model coefficients. Once derived, the RBF may be solved for any unsampled point or averaged over any volume to provide an estimate of grade. It is possible, for example, to query the RBF on a regular grid to derive an estimate of block grades. Given the ease of creation of an RBF, and its ability to predict grade, the question arises as to how the grades derived from the solution of an RBF compare with grade estimates derived from conventional geostatistical interpolation methods (eg ordinary kriging (OK)).The purpose of this paper is to describe in lay terms: the basic structure of an RBF the role of parametric choice in the solution of RBFs and how this influences the character of the solution the fundamental similarities and differences between RBFs and conventional geostatistical estimators.Using a high-resolution conditional simulation, we show that in many situations RBF and OK estimates are very similar.CITATION:Stewart, M, de Lacey, J, Hodkiewicz, P F and Lane, R, 2014. Grade estimation from radial basis functions – how does it compare with conventional geostatistical estimation?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018