Search Documents

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

By Waldram JT

The Kelsey Centrifugal Jig incorpo- rates the principles of operation of a conventional mineral jig, at the same time utilising high centrifugal forces to extend concentration to very fine heavy minerals. The main operating variables which are adjusted to control processing of different types of material are centrifugal force, ragging material and size distribution. Pilot plant trials have been under- taken to examine concentration of a mineral sand in which the heavy mineral particles occur mainly in the minus 0.075 plus 0.032 mm size range. Stage recoveries of greater than 90% were achieved at concentration factors of up to 2, although lower recoveries were obtained with higher concentration factors. A final concentrate containing 65% heavy minerals was obtained.

Jan 1, 1986

By R Bose, M Bovell, G Cheong

Grinding media is a major consumable in mineral processing and therefore decreasing costs associated with its consumption is regularly considered a key goal for the minerals processing industry. Grinding media manufacturers have historically developed steels with improved wear life for their products as a way of delivering incremental media quality improvement. This has included increasing carbon levels from low-to-medium carbon steels up to the eutectoid carbon composition of 0.77% where the relationship between higher carbon and better wear performance is well understood. Producers today will regularly use grades in excess of 0.8% to further improve wear performance particularly for rolled grinding media.This paper first introduces the demonstrated relationship between this increased carbon content and improved wear resistance along with metallurgical rationale behind the high carbon production process and limitations. To test the performance improvement associated with the higher carbon steel grade, a series of Marked Ball Wear Tests (MBWT) were carried out. This paper also explores the relationship between ball properties, test methodology and wear performance and concludes by correlating increased carbon grade with a reduced consumption rate of between 3.1% and 6.1% in the tests conducted.CITATION:Bovell, M, Bose, R and Cheong, G, 2018. Improved forged grinding media performance with carbon content greater than 1.0%, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 559–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The treatment of beach sands in'' the Bunbury/Capel' area for the extraction of ilmenite is a very recent development in the mining industry in'J7estern Australia. Nevertheless since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced. The increasing world recognition of W.A. as a major' Iiroducer of ilmenite is due primarily ' to its low chromic oxide. ; (Cr203 content,, 0,03% to 0.04%, combined with a medium to high grade TiO2 content, 54% - 6 , supported by large reserves, a'. stable government with close access to good shipping facilities.. Ilmenite is produced from-these deposits at low-costs, enabling the industry to compete on world markets despite high rates for sea freights because of the distance from.major markets.

Jan 1, 1964

A wide variety of process streams are sampled for grade control in the mining industry. However, in many instances the overall precision of the resultant analyses is inadequate for the intended purpose, ie grade control and optimisation of resource utilisation. Consequently, special attention needs to be given to the sampling, sample preparation and analysis procedures in place to ensure that meaningful grade control decisions can be made based on the analyses generated. For example, it is virtually impossible to control a process to within, say, ¦0.2 per cent if the overall precision of the analyses is no better than 0.5 per cent. Hence, precision targets appropriate for the task need to be established and the overall precision achieved in practice monitored and controlled on an ongoing basis.

Jan 1, 2008

By Quayle J. E

This paper covers period from 1973 through to 1988 and the mines of West Coast Mines, Elur Mine, North Mine and Risdon Zinc Smelter, now all part of the Pasminco Group. During this period, optimisation started with one mine (West Coast Mines) producing four Product concentrates with constant steady feed to the smelter and progressed to three mines producing eight products and a smelter varying feed inputs to maximise benefits. The initial optimisation was done manually using a desk top calculator and hand drawn graphs. This ultimately advanced to the use of PC plus linear programming software and spreadsheet generating relevant graphics. The financial benefits were achieved with no capital expenditure and increased from an initial $0.5 to $1.0 M/year (1973 $'s) to $5 to $10 M/year (1988 $'s).

Jan 1, 1991

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By Riel RG

Nickel and cobalt mineralisation at the Murrin Murrin deposits, in the North Eastern Goldfields region of Western Australia, occurs within laterites developed on Archaean serpentinised peridotite units. Lateritic weathering of the peridotite has produced a resource of 116.8 Mt at 1.10 per cent Ni and 0.082 per cent Co (resource at May 1996 with a 0.8 per cent Ni cut-off; see Fazakerley and Monti, this volume). The mineralogy of the Murrin Murrin laterites was investigated to identify the minerals hosting significant Ni mineralisation. Laterite profiles were studied using X-ray Diffraction (XRD), impregnated polished thin sections, and Energy Dispersive Spectroscopy (EDS) Electron Microprobe analysis, of RC percussion drill chips. This paper summarises the results of these studies, and briefly discusses the nature of the minerals hosting Ni mineralisation.

Jan 1, 1996

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

Long-range side-scan sonar and conventional geophysical data for the Peru Trench region (8`S-15¦S latitude) have been analysed. The data show that the Peru Trench is a site of sediment subduction where bending-induced normal fault-ing of the Nazca plate plays a key role. The sediments are continually removed from the trench axis region by their inclusion in normal fault-defined void spaces, such as grabens. In the process of subduction, the sediments are often offscraped, folded arid kneaded temporarily at the base of the shoreward trench slope. The subduction complex comprising such sediments is narrower than 20 km and its volume remains more or less constant due to regular removal of its contents along with the down-going plate. Addi-tionally, morphology of the subducting Nazca plate is responsible for subduction erosion of the South American plate, where the horst blocks cause tectonic erosion by abrasion and the grabens provide a mechanism for removal of the eroded material.

Jan 1, 1990

A new experimental procedure for determining the solids flux curve is detailed. The procedure is based on measuring the concentration at various heights of a bed of settled solids formed during a semi-continuous sedimentation test. Unlike conventional thickener area calculations, the test procedure demonstrates the dependence of the flux curve on the system feed flux. At a given feed flux, there was good agreement between the solids flux curve determined by the method and continuous sedimentation results. The widely used method of Kynch was found to be restricted to relatively high effective feed fluxes and consequently there was poor agreement with continuous tests at low feed fluxes. The flux curve determined by the method of Coe and Clevenger was invalid for all feed fluxes. A case study shows how the required thickener area would vary for a number of fine coal processing options.

Jan 1, 1989

By D Schwab, R M. Tosdal

The Quesnell-Stikine arcs, in the Canadian Cordillera, are host to Triassic and Early Jurassic alkalic porphyry Cu-Au and calc-alkalic porphyry Cu-(Mo-Au) deposits formed outboard of ancestralNorth America in island-arc tectonic settings (McMillan, 1991). The majority of the alkalic porphyry Cu-Au deposits are products of a discrete magmatic event at the end of the Triassic, with a second and smaller event in the Early Jurassic (Mortensen, Ghosh and Ferri, 1995). Of the Triassic complexes, the Galore Creek alkalic intrusive suite is one of the largest and most silica-undersaturated intrusive complexes, and host to the most significant undeveloped alkalic porphyry Cu-Au resource in North America (Lang, Stanley and Thompson, 1995). Because of the common presence of feldspathoidal-bearing rocks in the complex (Enns et al, 1995), Galore Creek likely represents an end member example of the alkalic porphyry Cu-Au class. The Galore Creek alkalic Cu-Au-Ag porphyry district, located in NW British Columbia (Canada), contains 12 mineralised prospects (Enns et al, 1995; Micko et al, 2007; Schwab et al, in press) with a total measured and indicated resources of 785.7 Mt at 0.52 per cent Cu, 0.29 g/t Au and 4.87 g/t Ag (NovaGold Resources Inc, February, 2008). The Central Zone is the largest and best delineated. Other economically important mineralised centres include the South-West, Bountiful, West Fork and Junction deposits. The South-West Zone, the focus of this contribution, is a Cu-Au-Ag breccia-centred deposit with a measured and indicated resource of 69 Mt grading 0.42 per cent Cu, 0.69 g/t Au, 2.67 g/t Ag. Hosted in brecciated intrusive rocks, the South-West Zone is distinctly younger than the Central Zone and most of the other mineralised centres (Enns et al, 1995; Schwab et al, in press). The South-West Zone therefore preserves the late stages of hydrothermal evolution at Galore Creek. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012