Search Documents

Jan 1, 1893

By G. M. Ritcey

Sulphuric acid leaching has been up to the present, the most popular of the leaching routes. Oxide ores are usually leached with sulphuric acid directly by dump leaching, as practiced at the Bagdad or Bluebird Mines in Arizona, or by vat leaching as done at Inspiration Mining in Arizona. Upgrading of the low-grade oxide ores by dump leaching followed by cementation of the copper from solution by scrap iron has been replaced by the leaching-solvent extraction-electrowinning route which results in a high purity product at the mill site at reduced production costs compared to previous practice. High-grade oxide ores, vat leached with H2SO4, can contain, for example, 25 g Cu/l and 25 g H2S04/,l, or higher concentrations of both, and are presently fed directly to electrorefining plants. Advantages of coupling solvent extraction-electrowinning with the low cost dump leaching instead of using cementation, are as follows (1): a) the production of high purity electrolytic copper rather than cement copper;

Jan 1, 1978

By K. Unrug, G. Herget, A. Smith

SUMMARY Statistics on roof falls indicate that the cost of just removing the unwanted waste from roof falls in US coal mines amounts to about $20 M per year. Almost 40 percent of fatal accidents occur under permanently supported roofs, indicating that the assessment of roof stability is still a very difficult task. In an effort to obtain a better understanding of roof fall occurrences, rock strength and ground stresses were determined in the roof of one mine each in Western Kentucky, northern West Virginia, and Eastern Kentucky. Triaxial ground stress determinations clearly show that horizontal stresses were higher than vertical stresses, and that maximum stresses in the horizontal plane were concentrated between the NE-SW to E-W direction, with the exception of the Eastern Kentucky site which was above the drainage. Magnitudes of stress components may vary considerably in one drlll hole. Strength tests of roof strata materials were done on core samples. Mapping of roof falls showed that the geometry of an opening or maximum span were not the overruling factor because in the same general area, a roof fall was observed in a room (entry) which connected two stable four-way intersections. It should be noted that, in very wet areas, the roof can break up to the bed where water is carried, and a very low ratio between extent of roof fall to height of roof, fall is observed. Geometry is, however, a contributing factor because nearly 70 percent of roof falls are intersection falls. The frequency of fractures parallel to bedding in failed roof strata is much higher than that observed in the original strata, indicating a significant amount of working in the roof before failure.

Jan 1, 1984

ALABAMA Alabama City.-Eddy, L. Altoona.-Cain, J. America.-Foreman, J. T. Anniston.-Foster, R. N. Ashland.-Sturdevant, J. C. Bessemer.-Ball, E. M. Calhoun, F. W. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr. Ashton, J. J. Aufderhaar, H. C. Ball, T. L. Biddison, P. M. Blair, C. S. Brown, T. S. Bush, M. W. Clark, G. H. Crawford, G. G. Crockard. F. H.

Jan 1, 1929

By Toshihisa Adachi, Shosei Serata, Shunsuke Sakurai

The present state of knowledge of three-dimensional rock properties does not provide an adequate basis for evaluating the safety of under- ground structures in situ. Most of the triaxial studies reported in the past have dealt with crushing strength, but have failed to consider the intergranular behavior and triaxial strain state of rocks. Without this information, the structural competence of rocks cannot be accurately assessed. The absolute three-dimensional testing method (ATT) was conceived for the purpose of analyzing the three-dimensional states of stresses and strains in aggregate rocks under conditions commonly encountered in underground structures. In-situ stress-strain states are not simple, even in the simplest possible form of opening, excavated in a homogeneous and isotropic rock medium. In general, there are four basic stress-strain states which are present in underground openings, regardless of the complexity of their geological conditions. They are the yielded, brittle-fractured, stress-relieved, stress-concentrated states, as illustrated in the schematic diagram, Fig. 1. The ATT machine was designed to create and study all these states in the laboratory. A theory describing the aggregate behavior of rocks under these diversified states is essential to evaluate the safety of underground structures. The Griffith theory is limited to tensile failure of ductile materials and therefore does not apply to behavior of aggregate rocks under compression. The Griffith theory also fails to consider the grain boundary characteristics of aggregates, which is the determining factor of rock behavior. The Mohr-Coulomb theory of failure ignores the importance of the intergranular behavior of rocks. An application of the continuum theory to

Jan 1, 1972

By Henry S. Drinker

THE Musconetcong tunnel is situated in New Jersey, near the line of the Central Railroad of New Jersey, about twelve miles from Easton, on the Easton and Amboy Railroad, the latter being the extension of the Lehigh Valley Railroad to tide-water. Up to the present time, the terminus of the Lehigh Valley Railroad has been at Phillipsburg, N. J., opposite Easton, passengers connecting there with New York by the Morris and Essex (D. L. and W.) and New Jersey Central lines; freight and coal being forwarded by the Morris and Essex to tide-water at Hoboken, and by the Central Railroad to Elizabethport and Port Johnson ; also, by the Belvidere and Delaware connections through Trenton to South Amboy.

Jan 1, 1875

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916

The writing that is effective is woven with a he texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned treatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of transmitting thought from man to man. To be understood beyond question, you should know not only what your words denote' but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home. The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called 'syntax'; and from the original Greek form, [s?ta???] (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By Frank Corwin

I. INTRODUCTION. SINCE the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 7, 1913

By Donald Barton

THE theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e. A= K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass.

Jan 1, 1928

By Charles R. Keyes

PAGE. I Introduction,........674 11. Occurrence............ 676 III. Geology of Death Valley BoRate-Region,....677 1. Surface.Relief ......677 2. Geologic Formations,....680 3. Geotectonics,..684 IV. FURnace Canyon Deposits..686 1. General Features..686 2. Geologic Structure..688 3. Ores.....690 4. Typical Section ...691 V. Lost Valley Deposits...693 VI. Mojave Desert Deposits..693 1. Distribution....693 2. Geologic Structure ........694 3. Ores............ 696 VII. Santa Clara Valley Deposits .699 1. Distribution....699 2. Geologic Structure..700 3. Ores.....700 VIII. Ventura County Deposits..701 IX. Geologic Occurrence of Borax .701 1. Original Sources...701 2. Solfataric Borax...702 3. Lacustrine Borax...703 4. Marsh Borax....703 5. Terranal Borax...704 X. Chemistry of Natural Borates.... 705 1. General Considerations.....705 2. Composition of Saline Waters...706 3. Solubility of Components....707 4. Time-Element in Water.Concentrations . 707 5. Effect of Temperature.....708 6. Effect of Pressure......709 XI. Occurrence of Other Commercial Salines,.... 709 I. Introduction. A complete transforrnation has taken place in the borax industry during the year 1908. A most remarkable factor in

Jan 1, 1910

By William E. Ford, Edward Salisbury Dana

I. Oxides of Silicon. 11. Oxides of the Semi-Metals : Tellurium, Arsenic, Antimony, Bismuth ; also Molybdenum, Tungsten. III. Oxides of the Metals. The Fifth Class, that of the OXIDES, is subdivided into three sections, according to the positive element present. The oxides of the non-metal silicon are placed by themselves, but it will be noted that the compounds of the related element titanium are included with those of the metals proper. This last is made necessary by the fact that in one of its forms TiOz is isomorphous with MnOp and PbOz. A series of oxygen compounds which are properly to be viewed as salts, e.g., the species of the Spinel Group and a few others, are for convenience also included in this class.

Jan 1, 1922

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By C. F. Jr. Tolman

IN February 1913, Prof. L. C. Graton and Dr. Joseph Murdoch1 presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations,. by the organization of a commission to undertake a "secondary enrichment investigation." In this work lie secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. Their report 2 on the chemical phases of the investigation has just been published. Incidental to investigations 3 carried on in my laboratory by advanced

Jan 2, 1916

By L. A. Mekler

THE recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are .constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to that produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack.

Jan 1, 1928

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By J. F. Kemp

PAGE Introductory Description of Deposits of this Type,.....244 Topography of the Ducktown Region,...247 Geology and Petrography,...248 The Mineralogy of the Ores and Gangue,..249 The older minerals : Amphibole, 250 ; Pyroxene, 250; Garnet, 251; Zoisite, 252; Calcite, 258 ; Quartz, 259 ; Apatite, 259 ; Rutile, 259. The Sulphides: Pyrite, 259; Zincblende, 259; Galena, 260; Pyrrho tite, 260; Chalcopyrite, 260. Later minerals, not belonging to the Gossan: Quartz, and certain sul phides, 261 ; Graphite, 261. The Formation of the Ore,...262 The Gossan Minerals,...........263 Bibliography,............265 Introductory Description of Deposits of this Type. Ore-bodies of more or less lenticular shape and lying parallel with the foliation of schists and slates form a group of

Jan 1, 1902

RichaRd PeaRce, Argo, Colo.: This contribution upon the very interesting subject of the origin of the gold of certain lode-formations offers many subjects for thonghtful consideration. The explanation, for instance, of the perplexing features of thin lava dikes seems to me to be in harmony with facts as I have myself observed them elsewhere. At Marshall basin, near Telluride, Colorado, there is an extensive lava-flow. The material of this formation contains a large proportion of fragments of foreign matter in the form of angular pieces of rock. The latter show no signs of having undergone metamorphism, such as would be expected to be due to the direct effects of heat; and the evidence in this particular case would certainly lead me to suppose that the flow was due to causes analogous to those suggested by Mr. Rickard. It was, I believe, a moving mass of material, having a temperatrire considerably below the actual melting-point of the rock of which it is composed. In regard to the theory which the author has built up from the existence of the iodide of gold in sea water, I cannot consider it untenable ; but I would put the question whether any investigations have been made with a view to determining whether gold and silver occur in the beds of rock-salt, formed, as is generally allowed, by the evaporation of bodies of salt water. At Stassfurt, in Germany, there is a very remarkable series of alternating beds of rock-salt and anhydrite, the uppermost members of which are covered with deposits of potash salts. The question occurs to me, why should not gold and silver have been discovered in these deposits? Iodine and bromine, I believe, have been found in the salts last deposited by

Jan 1, 1894

By Walter P. Jenny

I. The Reducing Action of Carbon and of Hydrocarbons,. .. 445 11. Protective Action of Carbon and of Hydrocarbons,. 451 111. Contributory Action of Carbonic Acid Gas,..452 IV. The Stability of Carbonic Acid and of Water,..453 V. Occurrence of Carbon and the Carbon-Compounds,. 455 VI. The Occurrence of Carbon, Alone,.... VII. The Occurrence of Carbon Combined with Hydrogen,. .. 460 VIII. The Relative Reducing Power of Minerals,..487 I. The Reducing Action of Carbon and of Hydrocarbons. Carbon has long been recognized as one of the most powerful reducing agents in the deposition of ores. Investigations, made by myself, of the zinc- and lead-deposits in Southwest Missouri, in the region centering about Joplin, where the formation of the metallic sulphides has been due to the action of bitumen, carbonaceous shales and bituminous coal, have afforded abundant evidence that the solid oxygenated hydrocarbons, particularly when in fine powder and in suspension in the waters circulating through the ore-bodies, are the most energetic and powerful reducing agents known. Bitumen, liberated by the decomposition of the ore-bearing limestone, is found in the Joplin mines in all degrees of fluidity and hardness, dependent on the amount of oxidation it has undergone. From semi-fluid maltha it grades into partly oxidized mineral-pitch, which, by further oxidation, changes to hard asphalt, finally breaking up, from continued absorption of oxygen, into a fine powder resembling in appearance powdered coal. In this condition oxidized bitumen, from its light gravity, is transported readily in suspension in the underground circulating-waters. Bituminous coal and black carbonaceous clays and shales occur as surface formations, often in intimate association with

Jan 1, 1903