Search Documents

By S. C. Schaeker, A. W. Schlechten, A. H. Larson

PARRAVANO and Malquori' studied the equilibrium of H2S-Hz with molybdenum and its lowest sulfide which they believed to be MoS2. Mc Cabe' has shown that its composition is actually Mo2S3 and determined its dissociation pressure by means of Knud-sen effusion measurements. Stubbles and Richard- son3 have recently studied the equilibrium of gas mixtures of H2S-HZ with the two-phase solid mixtures of Mo-MozS3 and Mo2S3-MoS2. The latter investigators found that M02s3 deviated slightly from the stoichiometric composition, but they did not determine the homogeneous region of the disulfide phase. Morimoto and Kullerud, studied the Mo-S system by quenching, microscope, and X-ray methods and concluded that the disulfide is stoichiometric. The present investigation was concerned with the measurement of the sulfur vapor pressure variation with composition at 1100°C in the homogeneous region of "MoS2". These measurements were made by reacting: 1) molybdenum powder (99.97 pct Moj with sulfur vapor, and 2) MoS1.g9 (formed by reaction of Mo + H2S) with sulfur vapor in a quartz capsule. Conditions were controlled to form an equilibrated phase within the homogeneous region of the disulfide. The quartz capsule was sealed off initially under a vacuum and the residual gases were gettered by titanium powder contained in one end of the capsule. A mixture of Mo + S or MOS,., + S was in the other end. The section containing the titanium powder was heated for 24 hr at 700°C and then removed by flame sealing. The end of the capsule containing the charge was then heated to 1100°C. The other end of the capsule was maintained at a temperature which would produce the desired sulfur pressure in the capsule (liquid sulfur distilled from the charge mixture was retained in this end). After equilibration, the capsule was removed from the heating assembly and rapidly air-cooled. It is assumed that equality existed between the total sulfur pressures (PT) in the two ends of the capsule and not between the partial pressures of the different molecular species (S, SZ, Three separately controlled heating elements were used to maintain the proper temperature gradient over the length (approximately 12 in.) of the capsule. A thermocouple-Wheelco "Capacitrol" system was used for temperature control of the two end heating elements within 2"C. The center heating element was controlled directly by a " Power -stat". Separate controlling and measuring thermocouples were used for both end heating elements. Pt-Pt(l0 pct Rh) thermocouples were used for 1100°C and Chromel-Alumel thermocouples were used for lower-temperature control and measurement of the assembly. Silver foil was wrapped around the end of the capsule containing the liquid sulfur to insure a constant temperature zone. The thermal gradient over the entire length of the capsule was measured to: 1) ascertain that the length of the constant temperature zone of the liquid-sulfur end and the sulfide end was sufficient, and 2) ascertain that the liquid-sulfur zone was the zone of lowest temperature. The data obtained in this investigation are shown in Fig. 1 and Table I. The total sulfur pressure (PT) and p(S2) were calculated from the data of Braune et UZ.~ The compositions of the equilibrated disul-

Jan 1, 1964

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By T. K. Perkins, R. N. Hoffman, O. C. Johnston

A simplified theory of viscous fingering in miscible systems has been developed. It predicts the correct functional relationship between pertinent variables and permits the calculation of the order of magnitude of fingering behavior for simple systems, such as linear or radial. The theory is based on the following four observations: (1) cross-flow takes place only near the ends of fingers; (2) the relative finger width is about 0.5; (3) fingers can be suppressed by transverse dispersion, the suppression being quantitatively described by a critical ratio of dispersion times; and (4) the widths of extending fingers are close to the minimum size finger that can grow at any stage of displacement. Fingering is studied in two-dimensional linear and diverging radial systems, both theoretically and experimentally. For linear systems, the length of the fingered region is proportional to mean displacement; the finger width is proportional to square root of mean displacement; and there is a small initial region void of fingers because of suppression by longitudinal dispersion. For the radial system, two limiting conditions are recognized. If the mean displacement is small compared with the wellbore radius, the length of the fingered region is proportional to the mean displacement. The width is proportional to the square root of mean displacement. If the mean displacement is large compared with wellbore radius, length of the fingered region is proportional to mean displacement, but the number of fingers approaches a constant value. Also, in the radial case there is a small initial region void of fingers because of longitudinal dispersion. INTRODUCTION The behavior of viscous fingers in miscible systems has been of interest to the oil industry for many years. Previous studies have clearly shown the existence and nature of fingers in small models.1,2,3,4 Engineering techniques for extrapolating to reservoir situations have been proposed. 5,6 Still, because of the lack of a real understanding of the mechanics of fingering, there remains uncertainty and disagreement as to the best way to scale or calculate fingering behavior in the reservoir. In this paper we discuss a study of the mechanics of fingering in miscible systems (i.e., why do fingers behave as they do?). A simplified theory is developed which we believe will (1) predict the correct functional relationship between pertinent variables, (2) permit us to calculate the order of magnitude of fingering behavior for simple systems such as linear and radial, and (3) give further insight into the problem of scaling or otherwise extending the results to more complicated reservoir conditions. The paper includes the following sections: (1) brief summary of the mixing behavior of miscible fluids in linear and radial systems; (2) four fundamental observations of fluid flow (under fingering conditions); (3) based on these four observations, a simplified theory of fingering in linear and radial systems is developed; and (4) the theoretical equations are compared with experimental fingering data measured in laboratory models. A REVIEW OF DIFFUSION AND DISPERSION As will be shown later, the behavior of viscous fingers in miscible systems is controlled in large degree by the mixing between the two fluids. A quantitative description of fingers will first require a quantitative description of mixing. Fortunately, much work has been done to clarify this subject; a fairly comprehensive review has been presented in a previous paper. 7 For present purposes let us (1) briefly summarize the quantitative description of diffusion and dispersion (both longitudinal and transverse) within a differential element; (2) present a simplification of the "width of mixed zone"; and (3) describe the effect of geometry on width of mixed zone. If one fluid is displaced from a porous medium by another miscible fluid (in the absence of fingers)

Jan 1, 1966

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson&apos;s ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young&apos;s modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott&apos;s work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger&apos;s single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By J. J. Taber

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton&apos;s equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?&apos; lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.&apos; It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By D. Turnbull, R. E. Cech

FISHER, Hollomon, and Turnbull have developed a theory for the nucleation of martensite. They first tested the theory on Fe-C alloys and low alloy steels. The major factor influencing nucleation of martensite was considered to be statistical composition fluctuations occurring in small regions at high temperature and frozen-in on quenching. These local regions of varying size and composition serve as nucleation centers. They become supercritical, one by one, as temperature is progressively lowered, resulting in temperature-dependent or athermal transformation. Fisher next applied nucleation theory to substi-tutional solid solution alloys. Detailed predictions were made for Fe-Ni alloys because of the availability of free energy data on this system. It was shown that composition fluctuations that were significant energy-wise did not occur, and nucleation frequencies could be calculated from average properties of the system. Nucleation was predicted to occur as time-dependent and having the functional relationship to give a C curve of nucleation frequency vs temperature. The analysis further predicted that the nucleation frequency was extremely sensitive to composition. Experimentally, it would be found that the transformation in some compositions is so slow that measurable amounts will not form in a reasonable length of time. With other compositions, only slightly different, the nucleation frequency becomes so great that the material becomes transformed while still distant in temperature from the maximum nucleation frequency. On quenching an alloy of such composition, the observed transformation kinetics would be similar to those found in Fe-C alloys. Cech and Hollomon repeated experiments of Kurdjumov n which the kinetics of transformation were similar to those predicted by Fisher for Fe-Ni alloys. The alloy studied in this investigation contained 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn. Fisher,&apos; using an idealized model for the extent of transformation as a function of the number of martensite crystals per grain of parent phase, derived nucleation frequencies from the transformation curves of Cech and Hollomon. Complicating influences such as coupling effects between grains in the polycrystalline specimens were neglected. Nevertheless, excellent agreement was found between the theoretically and experimentally derived nucleation frequencies. These experiments, however, could not provide a critical test of the theory. Experimental nucleation frequencies could vary widely from those calculated, depending upon the extent of deviation from ideal partitioning and the extent of coupling effects. Further, since the compositions of material theoretically analyzed and experimentally determined were different, the free energy changes involved in the experimental work could only be estimated. Also, the effect of heterogeneities on the transformation kinetics was not considered. For these reasons, it was decided that experiments designed to test the validity of the Fisher analysis must be conducted on binary Fe-Ni alloys, which were the ones considered theoretically by Fisher. The martensite transformation in Fe-Ni alloys has been the subject of considerable study. Machlin and Cohen have shown that transformation proceeds in a manner quite unlike that in any other ferrous alloy system. They found that single crystals would transform to a large extent in a single burst. In large grain polycrystalline specimens, frequently more than one grain and sometimes the whole specimen would transform at the same instant in this manner. Results on filings indicated that different particles would undergo the burst transformation at widely different temperatures. These results support the conclusion that the transformation behavior could not be described by a single nucleation frequency as would be the case if the nucleation were homogeneous. It appeared that further work was necessary to define the factors responsible for burst-type transformation, so that the conditions could be altered to favor homogeneous nucleation of martensite if such could be accomplished. This report summarizes the results of some experiments conducted with powdered Fe-Ni alloys for this purpose and the re-

Jan 1, 1957

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken&apos;s method1&apos; for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By A. E. Jenkins, L. A. Baker, N. A. Warner

The electromagnetic levitation technique has been successfully applied to rate studies of the de-carburization of liquid Fe-C alloys from 5.5 to zero pct C at 1660°C using gas mixtures containing 1 to 100 pct CO2 with CO or helium as diluents. The rate was shown to be independent of carbon concen -tration in the melt and only slightly affected by total pressure. The results were shown to be consistent with control either wholly or predominantly by gaseous diffusion. As well as avoiding side reactions with the crucible, levitation allowed precise calculation of reaction rates since the geometry of the system was accurately known. It also enabled interpretation using the established mass-transfer correlations for a gas flowing past a single sphere, The existence of gaseous-diffusion control and the extremely high rates of reaction reported for gas flowing past small spheres are of great practical significance in relation to current investigations into the use of spray-refining techniques in continzcous steelmaking. PREVIOUS work on the kinetics of carbon removal from liquid iron has generally involved the use of oxygen as the gaseous oxidant. Investigations have been made on commercial steelmaking furnaces and in addition laboratory-scale experiments have been attempted with a slag phase present. The general lack of agreement and the obvious difficulty in interpreting the results is at least partly due to the complexity of the systems used. This work has been reviewed by carter1 and more recently by Bods-worth2 and ward.3 The gas-liquid metal reactions have also been studied with slag-free melts by the conventional technique of blowing oxygen onto the melt contained in a crucible. The reaction between the oxidant and carbon could be followed by sampling either the melt or the gas phase. Side reactions with the crucible material have precluded direct interpretation of the results. Fujii, 5-7 using O-A mixtures, attempted to correct for the crucible reaction and reported that the reaction between carban and oxygen occurred at the melt surface and was controlled by gaseous diffusion for carbon contents greater than a critical value and by carbon-diffusion control in the metal for carbon contents less than the critical. The critical value was given as approximately 0.15 pct C. However, whereas this was the case for oxygen contents in the gas stream up to 10 pct, between 10 and 20 pct the rate was found to be approximately independent of oxygen content, and Fujii attempted to explain this observation by postulating the presence of an oxide "film".7 Turkdogan et a1.&apos; have studied iron fuming during decarburizing and suggested gaseous-diffusion control of the reaction above a critical carbon concentration, given as approximately 2 pct C. Filippov9-12 reports in a similar manner to Fujii but makes no mention of the crucible reaction with the carbon in the melt, even though this would be expected with the temperature, crucible material (MgO), and carbon contents used. Both CO2 and O2 were used as oxidant gases. In the present work the decarburization of liquid Fe-C alloys was studied using an adaptation of the electromagnetic levitation technique, and thus the complexities introduced by crucible side reactions were eliminated. In this technique a single sphere of the Fe-C alloy is freely suspended and heated by electromagnetic induction in a flowing stream containing the oxidant gas. The full range of carbon levels up to saturation was studied, the temperature of the melts in this instance being held constant at 1660°C. The oxidant was CO2 which was used either pure or in association with a diluent gas, the total gas pressure being maintained either at 1 atm or at a reduced pressure. Thus the reaction under study was:

Jan 1, 1964

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.&apos;-&apos; The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.&apos; The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.&apos; National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit&apos;s construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton&apos;s equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?&apos; lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.&apos; It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.&apos; The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By T. D. Mueller, H. Dykstra

This paper describes a method for obtaining compositions of gas and oil phases in equilibrium with each other at a given reservoir temperature and pressure as lean or enriched gas is injected into a reservoir oil not in equilibrium with the gas. The method is based on calculation of equilibrium constants, K, from the equation log Kp = A + B F, where p is pressure and F is component characterization factor. A and B are constants that vary with a composition parameter. The paper explains how A and B could be determined with a minimum amount of data. The method consists of calculating equilibrium constants as a function of liquid composition and using the K&apos;s to calculate changes in compositiort of injection gas as it successively contacts original resetvoir oil at the gas-oil front and the change in composition of reservoir oil as it is successively contacted by the injection gas in the vicinity of an injection well. An iterative process is required. Two examples of the method are given which show how oil and gas compositions and properties are calculated with the aid of a computer. INTRODUCTION The calculation of recovery from lean-gas or enriched-gas injection into a saturated or under-saturated reservoir oil requires a knowledge of how phase properties change in a reservoir between injection well and producing well. To determine the phase compositions or properties experimentally would be difficult and time consuming, especially if one wanted to look at the effect of various injection gas compositions. For some fields an engineer would want to make preliminary calculations on the economics of gas injection before he makes the decision to spend a corrsiderable sum of money for laboratory work to obtain the necessary fluid properties. A method for calculatine compositions and properties based on a minimum of laboratory data is described. The minimum amount of data required is injection gas and reservoir oil composition and injection gas solubility as a function of pressure for an undersaturated oil, or the compositions of mixtures of reservoir fluid with two or more enriched gases, which mixtures have a bubble-point pressure that is the same as the expected average displacement pressure. On the other hand, if the economics appear to be attractive, more laboratory data can be obtained in the form of equilibrium constants for three or more mixtures of the reservoir fluid and injection gases. The method is based on the calculation of K&apos;s from the equation, log Kp = A + B F, where K is equilibrium constant, p is pressure and F is component characterization factor. This method of plotting K data by means of the above equation is described by Hoffman, Crump and Hocott.1 A and B are constants that vary with a composition parameter. It is shown how experimental data are used to determine how A and B vary with composition. BASIS OF METHOD EQUILIBRIUM CONSTANTS Equilibrium constant (K) data are required for this method. The K of each component is obtained from an equation that gives the product of K and pressure as a function of component characterization factor. The characterization factor F = b(l/Tb — l/T), where b is a constant characteristic of a given component, Tb is the boiling point in OR at atmospheric pressure of the given component, and T is the temperature of the system in OR. This method of plotting K data is described by Hoffman, Crump and Hocott.l The straight-line equation of the log Kp - F plot is log hp = log Kop +BFi, where Kop is at F =0, i designates the component, and B is the slope of the line. The factor F can be

Jan 1, 1966

By H. S. Choi, I. Iwasaki

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer&apos; stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,2 Mitchell et aL.,3 and particularly Hamilton et al.&apos; have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski&apos;s French Patent No. 847,-215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores. The present article describes comparative results obtained at room temperature and at elevated temperatures by otherwise conventional flotation of iron ores, by single-mineral flotation in the Hallimond tube, and by contact-angle measurements. It is not the purpose of this article to evaluate the commercial feasibility of high-temperature flotation of iron ores, although preliminary calculations show that the cost should not be excessive and that the gains to be realized may well outweigh the extra cost of heating the pulp. LABORATORY FLOTATION TESTS Experimental: All flotation tests reported in this article that use a laboratory Fagergren cell were made on ore A (either containing the primary slimes or deslimed at 20µ as specified) following the preparatory procedures described elsewhere- or this particular ore. Ore A contained hematite, goethite (limonite), quartz, chert, and minor quantities of magnetite. Confirmatory tests made on other ores show that the same general principles apply to ores of similar mineralogy and structure. Conditioning was performed by adding the collector, as a soap, to the vigorously stirred and heated pulp. Conditioning time was 5 min, the pulp contained 60 pct solids, and the equivalent of 0.5 Ib of fatty acid was added per ton of original (unde-slimed) ore. The pH of the pulps ranged from 6.8 to 7.1 (25°C measurement) during conditioning. The pH was adjusted in the flotation cell by addition of either NaOH or H2SO4, the values reported being those of the pulp cooled to 25°C. During conditioning and flotation the pulp temperatures were controlled within l° to 2° by immersion of Variac-controlled Calrod elements in the conditioning beaker and in the cell, and by the use of water, heated to the appropriate temperature, for transferring pulp, adjusting pulp volume, and washing. Selectivity indexes have been calculated on the same basis as those reported in the article by Cooke, Iwasaki, and Choi." Results: Table I gives the results obtained by floating deslimed ore A with pure oleic acid at 25" and 50°C, and Fig. 1 shows the selectivity indexes plotted against pH of flotation. Inspection of Table I

Jan 1, 1961

By E. J. Harris

Mathematical solutions to complex mine ventilation problems are possible, but often the airway network is so complex that the mathematical solution becomes tedious and impractical. A fluid network analyzer, designed and built for analyzing mine ventilation problems has been in service at the Bureau of Mines&apos; Pittsburgh station for approximately nine years. Using this analogue as a model, the mine ventilation network is simulated electrically by a combination of series and parallel circruits laid out to conform with actual mine airways. A tungsten filament lamp, referred to as a Fluistor, is used to simulate mine airway resistance. With the analogue ventilation model established, voltages of the proper amplitude to represent ventilating pressures are impressed across the circuit at points where mine fans and airshafts are located. Comparison of mathematical solutions of complex systems against analogue results showed a maximum variance of 3% for pressures and 2% for quantities. An electrical fluid network analyzer, designed and built especially for analyzing mine ventilation distribution problems, has been in service at the Bureau of Mines, Pittsburgh, for approximately nine years. It is a nonlinear, low voltage, fluid network analyzer of the type developed by the late Malcolm S. McIlroy, Professor of Electrical Engineering, Cornell University, who cooperated with G. E. McElroy, of the Bureau of Mines, in adapting the instrument to mine ventilation systems. Several modifications have been made since the original installation, but a considerable part of this paper is drawn from G. E. McElroy&apos;s original description of the analogue.&apos; The analysis of water or gas distribution systems2,3 led to the development of this type of network analyzer. Several similar units are now employed by utility companies for this purpose; however, the Bureau of Mines unit is the only one designed specifically for mine airflow problems. Other airflow analogues employing a similar principle have been used at the Central Research Station of the Netherlands State Mines,4 in England,5 and in South Africa.6 Information on these devices indicated they were somewhat inflexible because commercial lamps with a sufficient range of resistance are difficult to obtain. Computers for mine ventilation analysis have been developed in Germany which instead of lamps use a variable resistance to adjust for turbulent flow laws. These units are expensive, but excellent results have been reported in their application. THE ANALYZER Theory of Application: As airflow generally follows the law of turbulent fluid flow, resistance to flow is nonlinear; consequently, the problem has been to find a nonlinear resistance element of suitable range that can be used for electrically simulated airflow. Tungsten filament lamps operated on alternating or direct current approximate the square-law resistance characteristics of mine airflow over a large range below maximum or rated voltage; that is, the voltage drop varies approximately as the square of the current. Consequently, the heart of the network analyzer is a nonlinear resistor known as a Fluistor, which is simply a custom-made low voltage, tungsten filament lamp that is available in a progressive series of relative resistance values ranging from 0.05 to 500 in nominal 5% steps. However, variations in manufacturing large groups result in differences of 1 to 3%, but series arrangements required for high-loss branches can be matched within about 1%. Utilizing a combination of Fluistors and load circuits, the mine ventilation system is duplicated electrically. Intake load circuits are connected from power intake to primary points of the circuit network; segments of unregulated flow along intakes and returns are represented by Fluistors, regulated splits and leakage paths are represented by load circuits and Fluistors of proper capacity; and mine exhausts are connected to ground from the last point of the network to complete the circuit. For the special purpose of representing booster fans or natural draft conditions, boosters or separate source circuits are provided that can be inserted between any two points of a network to increase voltage to the required value. Physical Layout: The analyzer consists of three 42

Jan 1, 1963

By O. K. Miniato, L. Massé, K. Nobe, J. S. Aronofsky, W. F. 213-000-000-016 Seyer

MUCH work has been done dealing with the effect of mechanical stress on electrode potential in an electrochemical system. The contradictory nature of the experimental results indicates the complexity of the problem although thermodynamic considerations show that a simple relationshir, should exist. In those systems where a gas was the electromotive active substance satisfactory agreement between theory and practice has been found. Des Coudres&apos; found this to be so even when the active substance of the electrode, in this case mercury, was in the liquid state. In contrast, attempts to correlate theory and experiment for the solid state have met with a very limited success. The early workers in this field, Andrews,2 Walker and Dill3 used iron, certainly one of the most reactive of metals. Others have made use of less active metals such as copper and nickel. Recently Fryxell and Nachtrieb4 investigated the electrochemical behavior of gold and silver under both tensile and compressive stresses and concluded that it was doubtful whether true stress potentials could ever be measured. Much of the lack of success to measure the thermodynamic stress potential can be ascribed to the presence or formation of a complex film on the metal surface in contact with the electrolyte. Further, the theoretical stress potential is very small and therefore difficult to measure directly. Thus the calculated emf between a 24 B & S gage cold-drawn copper wire stressed with a weight of 1 kg and an unstressed portion of the same wire is only 2.60 X 10"7 volts. This is very small compared to that which can be produced by chemical reactions at the metal electrolyte interface which in turn can be so large as to mask completely the stress potential. Hence in this type of measurement all chemical side effects must be eliminated or reduced as much as possible. It was for this reason that the system copper-sodium chloride solution was selected for study. INSTRUMENTATION In the many preliminary experiments conducted, two major difficulties were encountered. The first was to measure the small electro-potentials to be expected and the second to obtain a suitable electrode surface. The conventional potentiometric method was found to be unsatisfactory for measuring the small emf expected. However, by using an L & N No. 2290 galvanometer having a resistance of 915 ohms consistent measurements were possible. The reference electrode was always the unstressed one made from the same sample of wire. The steady current flow was approximately 10-8 amp. Lewis and Randell5 have stated that for currents of the order of 10-8, if there is no sensible polarization, the measured emf may be taken as a reversible one. To check the galvanomenter readings an alternative method was devised to measure the potential difference between the wires. This involved a Liston-Falb d-c breaker amplifier model 10, an L & N k-2 potentiometer and a moving-coil galvanometer having a sensitivity greater than 0.1 µv (microvolt) per mm. To increase further the output voltage of the amplifier a d-c amplifier, model B. L.-932 was introduced into the circuit. This amplifier was in turn connected to a Brush recorder which had been calibrated previously by the test signals from the Liston-Falb instrument. These test voltages employed took into account the impedance of the input current. Unfortunately, this method had too low a sensitivity for measurement below 10 µv. Above this value the voltage agreed reasonably well with those obtained directly by the simple galvanometer method. The main advantage of the amplifier setup was that one did not have to wait until no deflection occurred on the galvanometer in the circuit when first exposing the wires to the solu-

Jan 1, 1959