Search Documents

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By I. Fatt

The chromalographic effect refers to the separation of constituents in a moving fluid phase which occurs when the phase is passed over a stationary phase, either solid or liquid, or large areal extent. In performing chemical analyses, the large surface contact areal is provided in the case of gas-solid chromatography by-passing the gas over a porous solid and for gas-liquid chronla tog rap hy by-passing the gas over a porous solid which has been coated with a nonvolatile liquid. The porous medium is usually placed in a cylindrical tube, although it may be a relatively flat sheet as in paper chroma-tography. According to one theory,' the separation results from the difference in time spent by various components in the stationary phahe. A gaseous component which is conlpletely insoluble in the stationary phase, or is not adsorbed on the solid, proceeds unimpeded through the column. The versatility and power of the various types of chromatogruphy for the analysis of complex mixtures are evident from their widespread use in performing chemical analyses and from the large number of symposia, books, and papers devoted to the subject in recent years. Associated developments are the application of chromatography to the determination of heats of solution, heats of adsorption, solubilities orK-values, etc. Gas-liquicl chromatography analyses may be characterized by the manner in which the samples are introduced and displaced from the column'. The three techniques used are known as (1) frontal analysis, (3) displacement analysis, and (3) elution analysis. The frontal analysis is performed by displacing an inert gas from the column by a continuous stream of the sample. As indicated in Fig. l(A), all but the first fraction leaving the column represent mixtures rather than pure components. The displacement analysis is conducted by filling the column with a sample, then displacing it with a more strongly adsorbed or absorbed vapor. The resulting chro-matogram is illustrated by Fig. 1(B). Finally, in the elution analysis a small sample of the mixture to be analyzed is introduced as a "plug" into a Rowing stream of carrier gas to give an elution-type chromato-gram. Fig. l(C). The three techniques may be used to provide models to which Row patterns in other physical situations may be compared. PURPOSE OF THE INVESTIGATION The purpose of this investigation was to determine whether natural reservoir rocks, when coated with crude oil, provided sufficient surface areas to give rise to a chromato-graphic separation of light hydrocarbon constituents. The tests were conducted with the light hydrocar-bons in the gaseous state. SANDS TESTED Two sands of widely different permeabilities have been studied: (1) Ventura core (16 md), and (2) Torpedo sandstone core (578 md).Table 1 gives a description of the cores that were tested. With the exception of one frontal-type flow arrangement which was performed on Core 3, the tests were of theelution-type in which a methane-propane mixture was eluted through the core by means of helium. The Ventura core, when impregnated with a weathered crude from the same field, became so impermeable to gas flow that it was necessary to conduct the tests on the granulated cores (Cores 2 and 3).

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relationships proposed by Rittinger,2 Kick,3 and Bond.' That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes' developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill. Basic Principles: In a batch mill the length of time during which the material is ground is a direct measure of the energy expended on the material, except possibly for exceedingly fine grinding. However, in a continuous operation, the fraction of the total expended energy which is useful for grinding will vary according to feed rate and amount of material in the mill. If the amount of material within a continuously operating vibratory mill is low enough so that only part of the expended energy is used for grinding, the extent of size reduction at constant power input must depend upon the length of time the material is retained within the mill, namely, upon retention time. The following analysis pertains to a continuous mill operating under these conditions. The empirical differential equation that applies to the comminution of brittle materials is:" dE = -Cdx/x" [1] where dE is an infinitesimal energy expenditure, C a constant, dx an infinitesimal size change, x the particle size, and n a constant. For continuous grinding in an open circuit at constant power input, P, Eq. 1 must be written as (dtr)P = -C dx/x" [la] where dt, is an infinitesimal time during which a particle of size x is in the mill, and C' is a constant. A ground product never consists of particles of single size but always comprises a distribution of sizes. In comminution, the expenditure of energy causes a lateral shift in the size distribution.', ' " The general objective of any engineering study of comminution is to correlate the magnitude of this size distribution shift with the energy expended, the ultimate aim being to cause the greatest shift with the least amount of expended energy. Although a number of criteria can be used to measure this shift, Schuhmann's size modulus has been found convenient.' Mathematically, the Schuhmann size distribution can be expressed as follows:" y = l00(x/k) [2] or in differential form: dy = [F- xa-' dx ] K, where y is percentage of material finer than size x, a is a constant that determines weight distribution among particles of various sizes, and k the size modulus that denotes the theoretically maximum-sized particle in any size distribution. By considering the energy required to reduce an element of weight of material, dy, from size x, to size x, the element of time during which the material must remain in the mill at at power will be (dt..).= J'-Cax!(dy) [3] Summing up all the elements of weight from zero to 100 for a product that conforms to the Schuhmann size distribution yields C C f Cdx,\( 100«x°-'dx\

Jan 1, 1960

By P. E. Baker

An improved method of logging formation density has been developed in which the formation is bombarded with a collimuted beam of gamma rays. By means of a scintillation detector and pulse height discriminator, the gamma-ray energy band is accepted and recorded which corresponds to deepest penetration into the formation. Laboratory tests on a field tool revealed no borehole diameter effect for smooth holes and no effect of formation chemistry, except insofar as chemistry affects density. In extensive field tests, the density log has exhibited satisfactory agree-ment with core measurements and has correlated accurately with other logs. INTRODUCTION This paper describes an improved method of logging formation density by means of back-scattered gamma rays to penetrate the formation together with energy discrimination to select only that energy (or frequency) range corresponding to deepest penetration into the forma- tion. This method of density logging was developed at the La Habra laboratory of California Research Corp.* Field instruments have been built and tested by McCullough Tool Co. and commercial service has begun in some areas. All of the data discussed here were obtained for the original field tool. The density log can be a valuable adjunct to existing logs because of its use in determining porosity quantitatively. It is useful also in connection with seismic and gravity surveys where formation density information is of interest. PHYSICAL PRINCIPLES The intensity, I, of a beam of gamma rays after traversing a distance, x, in an absorbing medium is given by I = loe -ax where I, is the intensity of the beam entering the medium and a the attenuation constant or macroscopic cross section of the medium for gamma-ray absorption. The macroscopic cross section depends on the number and types of atoms per unit volume and the gamma-ray energy. In brief, it is the sum of the atomic cross sections of all atoms per cubic centimeter. The density of the material is the sum of the masses of all atoms per cubic centimeter. Thus, the density and the macroscopic cross section for gam-ma-ray absorption vary in propor- tion to the number of atoms per cubic centimeter. The density of the material increases, of course, if the atomic masses increase without a change in the number of atoms per cubic centimeter. When the density increases in this latter way, the macroscopic cross section increases also, but disproportionately. This results from the fact that part of the gamma-ray absorption arises from the photoelectric effect and the pair-production effect**, which are proportional to the sixth and to the second power, respectively, of the atomic number of the absorber. The remainder of the absorption results from the Compton effect, and is directly proportional to the atomic number. The gamma rays that undergo Compton scattering are not immediately absorbed. Since these rays are scattered in all directions, a fraction will emerge from the face of the medium at which they entered. If a gamma-ray shield is placed between the source and detector, most gamma rays reaching the detector will be those scattered out of the medium. The intensity will depend on absorption and scattering in the medium, and so indicates the density of the medium. For gamma rays for which Compton scattering prevails, the intensity

Jan 1, 1958

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan's blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations '-' of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin') apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder's Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By J. B. Dorsey, T. W. Brinkley

Performance of a high-pressure, vaporizing gas-drive project in a volatile oil reservoir is discussed. The project has been in operation for over 8 years. Present recovery from the over-all displaced portion of the reservoir is 40 percent, and an ultimate recovery of 60 percent is indicated. Calculations reflect an over-all displacement volume of 50 percent for the entire reservoir; therefore, ultimate oil recovery will be 30 percent of the entire reservoir oil originally in place. Laboratory vaporization tests conducted prior to project initiation also are presented and discussed, along with an analytical method of determining stock-tank oil production and gar injection requirements related to over-all volumetric displacement efficiency from these data. Introduction The Shoats Creek field is located in Beauregard Parish, La., in the extreme western part of the state (Fig. 1). Discovered in 1956, the field is productive in three Cockfield sand zones, ranging in depth from 8,000 to 9.000 ft. The upper two zones, 1st and 2nd Cockfield, are condensate-bearing gas reservoirs. The lowest zone, the 5th Cockfield, is a volatile-oil reservoir. Laboratory work conducted on crude oil from the 5th Cockfield zone shortly after field discovery demonstrated that, when contacted with dry gas, signidcant volumes of the oil could be vaporized at reservoir temperature and at an appropriately high reservoir pressure. Further study led to the conclusion that early initiation of a crude vaporization project in the 5th Cockfield zone would be superior economically to other methods of reservoir depletion. Consequently, the zone was unitized and gas injection operations started late in 1958. This paper discusses laboratory work performed in conjunction with the project, and project performance to the present. History of Development The 5th Cockfield zone in Shoats Creek is composed of a thin, very shaly, low-permeability sandstone. Oil accumulation is controlled by a structural trap bounded by faults along the north and west and by a water contact on the southern boundary (Fig. 2). The zone covers a productive area of 1,550 acres at an average depth of 9,000 ft. The net sand section is thin, having a maximum thickness of 10 ft and an average thickness of 5.5 ft (Fig. 3). Average reservoir rock properties, as determined from core analysis are presented in Table 1. Shaliness of the zone is illustrated by the typical electric log of the 5th Cockfield section in Fig. 4. Because of the thinness and poor quality of the sand, the 5th Cockfield was developed on a wide spacing. Eleven completions were made in the zone between 1956 and 1961 for an average density of 140 productive acres per completion, with the majority of wells being dually completed in the 2nd and 5th Cockfield. Average initial potential for producers in the 5th Cockfield was 130 BOPD. Oil from the 5th Cockfield has a stock-tank gravity of 50.5" API; with a bubble-point pressure of 3,515 psia, the oil was highly undersaturated at the original reservoir pressure of 4,675 psia. Pertinent properties of the oil as determined in the laboratory are presented in Table 2. Because of the volatile nature of the crude, laboratory studies of its susceptibility to vaporization, as well as a vapor-liquid phase study, were conducted in addition to a standard PVT analysis. The vaporization study was conducted in a visual cell; a stepwise illustration of this work and laboratory measurements are presented in Fig. 5. Field

Jan 1, 1969

By Robert M. Asimow, Bisuddhi Riddhagni

THE use of back-reflection Laue photographs for crystal orientation is standard in many research projects. The time required for the orientation of any given crystal depends largely on luck and the skill of the investigator. In any case, where large numbers of crystals are used, this time can be quite considerable when the standard methods involving a Greninger chart and Wulff net are employed. For this reason the technique described below was developed. This new procedure applicable for cubic crystals (without preparation of new charts) largely eliminates the skill and luck factors and makes possible the determination of orientation in minutes. The procedure works in the following way: the Laue photograph is examined and arbitrarily an important hyperbola is picked out. An important hyperbola is defined as one which contains some spots through which several hyperbolas pass. Such a hyperbola inevitably corresponds to a low-index zone axis. The angles between the reflection planes causing all the spots on this hyperbola can be read directly from a Greninger chart in the usual manner. If the hyperbola contains more than five spots, these interplanar angles will positively identify the zone axis and the indices of each of the reflecting planes. However, initially since neither the zone axis nor the Miller indices of a diffraction spot are known, there are a very large number of possibilities that must be considered. Using tables of interplanar angles to check out every possibility would be quite tedious, so that this approach is not generally used. Instead, various poles are plotted on a stereographic projection. In the cubic system, however, it is possible to plot out once and for all the angles between all planes of a particular zone axis up to some upper limit of Miller indices. This has been done for all low-index zone axes in Fig. 1. Given these charts, it is quite a simple matter to identify the spots of the unknown hyperbola. All that is necessary is to plot the angles read off the Greninger chart to the same scale as Fig. l(b) on a strip of paper. Then this strip can be slid along each zone axis of Fig. l(a) until a good fit is obtained. Once this is accomplished, the Miller indices of each spot are given and thus the orientation problem is solved. To check, it is possible to pick a second hyperbola and see whether a compatible solution is obtained. This is most conveniently done by picking for the second hyperbola one that contains a spot common with the first. If the specimen axis is chosen parallel to the incident X-ray beam, then usually the [ loo] hyperbola will appear on the film as one of the more important hyperbolas and consequently will be either chosen initially or as a check. Using the [100] hyperbola, after the (001) or (011) spots have been identified, the latitude and longitude of the specimen axis can be read directly from the Greninger chart so that it is unnecessary to use a Wulff net for the entire orientation procedure. This makes the operation not only quicker but more accurate. Of course, if neither the first nor second hyperbolas correspond to [loo] then a third hyperbola can be chosen.

Jan 1, 1967

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By L. W. Sink, B. H. Kear, S. M. Copley, M. F. Hornbecker

IT is well known that under appropriate conditions of chill casting, many metals and alloys develop a columnar grain structure having a high degree of preferred orientation.' In cubic materials, this principle has been employed to produce shaped castings with a unidirectional cube oriented columnar grain structure as well as shaped single crystals with a cube axis parallel to the growth ais.' "he purpose of this note is to describe how this same principle can be enlployed to produce wires, rods, or more complex crystal Shapes with a variety of conlpositions in cube or random orientations by a single casting operation. The procedure for directional solidification of in Fig. 2. Examination under crossed polarizers indicated that the striations were a second phase (presumably the B19 phase) which frequently forms initially at primary grain boundaries and then grows toward the interior as thin ribbons. X-ray studies on filings of this alloy reannealed at 1300°C for 15 min indicated a strong pattern of the fcc phase together with a substantial pattern of the B19 phase. The un-annealed filings, however, showed only the pattern of a cold-worked, fcc structure. In these two-phase alloys it appears, therefore, that the B19 phase is transformed into a disordered fcc structure by cold-working. The mechanical properties of these alloys would be of some interest since a fcc structure might be expected to possess greater ductility than the or-thorhombic B19 structure from which it forms. The author wishes to thank Mr. Harvey Yakowitz and Mr. Richard Manuszewski for obtaining the photomicrograph in Fig. 2. This research was partially supported by Research Grant DE-02455 from the National Institute of Dental Research. columnar grained ingots involves pouring a melt into a preheated mold having a water-cooled copper chill at its base? and controlling the temperature gradient in the mold so as to maintain columnar grain growth from end to end of the ingot.4 This is illustrated schematically in Fig. l(a). It should be noted that the longitudinal temperature gradient promoting unidirectional columnar grain growth is maintained by heat loss primarily through the solidifying ingot to the chill, so that both the temperature gradient and the growth rate diminish with increasing distance from the chill. As the distance from the chill increases? the columnar structure coarsens, and the perfection in preferred orientation tends to increase progressively. Using this same procedure of gradient solidification, Fig. l(b) shows a simple scheme for producing a batch of crystals having the same cube orientation rather than an assemblage of columnar grains. Wires and rods are produced by cementing ceramic tubes to the wall of the mold. The steep temperature gradient produced in the central chamber is controlled by the mold heater to produce favorable conditions for crystal growth. Clearly the success of the operation lies in the selection of individual growing columnar grains by some kind of orifice at the base of each channel in the mold. Using simple constrictions, experience with nickel-base alloys has shown that 4 -in.-diam holes at a distance of -1 in. from the chill yield crystals within 7 deg of (100); closer control of orientation is possible by placing the crystal selector farther away from the chill.

Jan 1, 1970

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By G. S. Upadhyaya, A. D. McQuillan

HERE would appear to be a simple relationship between the group number in the periodic table of the early transition metals and the maximum amount of hydrogen which they can absorb.' Thus group IIIA metals (Sc, Y, and La) yield a trihydride in which the metal atoms are on a fcc lattice and the hydrogen atoms occupy both tetrahedral and octahedral interstices. Group IVA metals (Ti, Zr, Hf) form dihy-drides in which the metal atoms are on either a fct or cubic lattice, but in which only the tetrahedral interstices are occupied by hydrogen atoms. In group VA (V, Nb, Ta) the hydrogen-saturated metal attains a composition slightly below that of a monohydride under normal conditions. Finally the metals of group VIA (Cr, Mo, W) do not dissolve appreciable quantities of hydrogen. The manner in which hydrogen solubility disappears on alloying a group VA metal with one from group VIA has previously been investigated.2 It is necessary, in order to obtain a general picture of the reactions of alloys of the early transition metals with hydrogen, to examine a system containing metals from groups IVA and VA in which there must be a change from a fcc to a bee hydride phase. The system chosen for investigation was the pseudobinary system between titanium hydride and niobium hydride. Metallic alloys were prepared by melting iodide-prepared titanium with zone-refined niobium in an argon-atmosphere are-furnace. To ensure homogeneity each alloy was cold-swaged and then heated at 1250°C in a high-vacuum furnace until metallo-graphic examination confirmed its complete homogeneity. Small weighed specimens of the alloys were charged with hydrogen using gaseous hydrogen generated by heating titanium hydride. The apparatus has been described elsewhere.3 Throughout the charging process the hydrogen pressure was kept at about 1 atm while the specimen, initially at 800 °C, was slowly cooled to 150°C over a period of days. The total amount of hydrogen absorbed by each specimen and the room-temperature crystal structure of the hydride powders were determined. The X-ray investigation indicates that the fee hydride phase arises from alloys extending in composition from titanium to 67 at. pct Nb. After a two-phase field lying between 67 and 74 at. pct Nb in which the fee and bee hydrides coexist, all alloys richer in niobium yield a distorted bee hydride. Data derived from parameter measurements are presented in Fig. 1. The atomic volume per metal atom has been plotted against the composition of the initial metallic alloy in order to facilitate comparison of the effects of hydrogen addition in the two phases of different crystal structure. The amount of hydrogen absorbed by each alloy at saturation in terms of the hydrogen to metal ratio and alloy composition is given in Fig. 2. Over the whole range of the fee hydride phase the hydrogen content remains constant, while in the distorted body-centred hydride phase, the hydrogen content increases with increasing titanium content reaching a hydrogen/metal ratio of 1.4 at the boundary of the two-phase region. It seems likely, therefore, that the maximum hydrogen content of the fee hydrides is limited to a hydrogen/metal ratio of 2 because hydrogen atoms

Jan 1, 1962

By P. E. Baker

The commercial neutron-gamma log measures the intensity of gamma-rays produced by the interaction of neutrons with nuclei in the formation and in the bore hole. This measurement gives information concerning the distribution of neutrons around the neutron source, and in particular gives information on porosity or fluid content. Another type of information is contained in the frequency or energy spectrum of the neutron capture gamma-rays. The capture gamma-rays of each element, in fact of each isotope, have only those energies characteristic of that isotope.'" The neutron capture gamma-ray spectrum, if obtainable, would permit the identification of the elements producing the spectrum. Such information would have considerable value in oilfield exploration work if it could be applied practically in well logging. Experiments have been carried out at the La Habra Laboratory of California Research Cop. to determine the feasibility of a method of well logging in which neutron capture gamma-ray spectra are measured down hole. In these experiments, spectra were obtained for artificial formations under simulated borehole conditions, using actual borehole geometry. This paper will describe the experimental apparatus and methods and will present the spectrum curves for several formations. THEORY Basic Formulas The neutron capture cross section of an element is a measure of its tendency to capture neutrons. The macroscopic cross section, or cross section per cubic centimeter, of a material composed of several elements is the sum of the cross sections of the nuclei making up 1 cc of the material. This is expressed in the equation SB = Sn1s2, ..........(1) where SB is the macroscopic cross section, s, is the cross section of a nucleus of type i, and ni is the number of nuclei of type i/cu cm. If N is the number of neutrons absorbed per second by the composite material, then the number captured by element j is Ni = N nisi/SB = N nisi/Si ni si ......(2) When the nucleus captures a neutron, a new nucleus is formed, which is usually in an excited state and falls to its ground or unexcited state by emitting one or more gamma-ray quanta.* The emission spectrum has been measured for many elements (see Table 1). The intensity of gamma-rays produced by an element is proportional to the number of neutrons captured per unit time by the element, which in turn depends on the capture cross section of that element and the capture cross sections of the other elements present which are competing with the first element for thermal neutrons. In a small sample of material the number of neutrons, N, captured per second is N = ?SB, ..........(3) where $ is the thermal neutron flux and SB is the macro-scopic cross section defined above. The number of neutrons captured by element j is N1 = ?ni si = N ni si/SB . ......(4) The number of gamma-ray quanta of energy, E, pro-duced per unit time by element, j, is I(E)=Nni si/SB P(E) .......(5) where P(E) is the emission probability of element, j, for this gamma-ray energy. Borehole Effects The capture gamma-ray spectra of many elements have been measured accurately in academic and government laboratories. These measurements are made on small samples, and from these measurements the emission spectra of the elements are obtained.

Jan 1, 1958

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By J. Weertman

The paper of Gifkins and Snowden considers the interesting but difficult problem of determining the stress dependence of secondary (steady-state) creep at low stresses. These authors have concluded that at stresses below 250 psi (2 x 107 dynes per sq cm) the secondary creep rate of lead is proportional to the stress (viscous creep) and is not proportional to the stress raised to about a fifth power. The experimental data considered by them were obtained on tests conducted at room temperature and at 50°C. The lowest stress employed was 50 psi (3.5 X 106 dynes per sq cm). The authors pointed out the main difficulty in determining the stress dependence of creep at low stresses. The creep tests must be run for very long lengths of time. However they made no estimates of when an experimental creep rate determination must be rejected because it does not represent a true steady-state or minimum creep rate. In order to be certain that a creep curve is within the steady-state region, the total creep strain should be of the order of 0.1 to 0.2. For a creep test of a year&apos;s duration this requirement implies that a secondary creep rate smaller than about 10-3 per hr cannot be measured reliably. The corresponding creep rate for a 10-year test is 10-6 per hr. The creep rates of the tests that were considered by the authors to prove the existence of viscous creep were of the order of or less than 10-6 per hr. One can conclude reasonably that this data does not prove unambiguously that large strain steady-state creep rate of lead is proportional to the stress in the stress range of 50 to 250 psi (3.5 x 106 to 2 X 107 dynes per sq cm). Another technique can be used to obtain the stress dependence at low stress levels. The creep rate is a very sensitive function of temperature. The creep rate can be increased by very large amounts merely by increasing the temperature. We carried out steady-state creep tests on lead single crystals25 at temperatures up to 320°C. We were able to obtain creep rate data down to stresses as low as 35 psi (2.5 x 10&apos; dynes per sq cm). Our smallest creep rate was 8 x 10-5 per hr. Thus we obtained large strain, steady-state creep rates to even lower stresses than were considered by Gifkins and Snowden. No evidence was seen for viscous creep. The creep rate was proportional to the stress raised to about a 4.5 power down to the lowest stresses. Since there is no reason to believe that changing the temperature should change the stress dependence of steady-state creep, we feel that large strain viscous creep does not occur in the stress range quoted by the authors for lead single crystals or large-grain polycrystalline samples of lead. This conclusion does not imply that viscous creep may nat occur in a lower stress range or in the same stress range for fine grain material or at creep strains very much smaller than 0.1. Support by the U.S. Office of Naval Research is acknowledged. Authors&apos; Reply R. C. Gifkins and K. U. Snowden We thank Dr. Weertman for his discussion and although, as we hope to show, we do not agree with his reservations, we do concur in stressing the importance of ensuring that creep rates are reliably obtained. Dr. Weertman appears to be content to accept n = 1 for low stresses with fine-grained material but not for single crystals. We believe our results show that the former result cannot be accepted without also accepting the latter. We will also show that the probable errors in our minimum creep rates are insufficient to alter our conclusions, that the criterion proposed by Dr. Weertman is arbitrarily restrictive and his alternative experimental approach possibly invalid. 1) A principal result of our Fig. 1(a) is that n = 1 for polycrystalline specimens at room temperature and 50°C for stresses below -250 psi. There was evidence that crystal slip and grain boundary sliding contributed approximately equaily to the overall strain in this low-stress regime. This implies that either a) grain boundary sliding controls slip within the grains or b) both grain boundary sliding and crystal slip independently occur according to mechanisms which give n = 1. Alternative a does not seem acceptable, so we were forced to consider b. This led us to reexamine work on bicrystals by Strutt and Gifkins and plot curves Fig. l(b). Previously Strutt et al. (loc. cit.), had merged these points with others using the Zener-Holloman parameter and thus, we now believe, had been led to overlook the behavior where n = 1. Curves C and D in Fig. l(b) did appear to confirm the hypotheses that n = 1 for crystal slip at these low stresses and the sliding curve F was similarly of the expected form. It was comparatively easy to find a quantitative theory to account for n = 1 for sliding and the similarity of curves C and D to curve F (all obtained from the same set of specimens) led us to feel that the single-crystal curves were valid. 2) We believe the secondary creep rates for both the polycrystalline and single-crystal specimens to be in error by factors c2. In Fig. 6 creep curves for polycrystalline specimens of lead(1) and lead(II) are reproduced as curves a and b, respectively, and curve c is for a single crystal at 100 psi. It is clear that, although the attainment of secondary creep rate takes 2 years for a and 150 days for b, thereafter the curve is linear for periods of 7 and -1 year, respectively. The single crystal has a linear portion commencing after 20 and extending to 90 days. Creep extension was measured directly using a traveling microscope reading to 0.01 mm on gage lengths marked on the specimens; the gage lengths

Jan 1, 1968

By R. F. Mehl, C. E. Birchenall

R. E. Hoffman and D. Turnbull—The authors have presented evidence which they have interpreted as indicating that the rate of self diffusion is not intrinsically more rapid at grain boundaries than within the grain. Grain-size effects which apparently exist are attributed rather to impurities concentrated at the grain boundaries. In view of our own experiments and the existing evidence, we believe that the support for this hypothesis is not convincing. We have in progress an investigation in which the rate of self diffusion of silver is being measured over an extended temperature range in both single-crystal and polycrystalline specimens. The results of the single-crystal experiments and some preliminary data on fine-grained polycrystalline specimens have already been reported:&apos; and it is anticipated that a complete report will be published in the near future. The self-diffusion coefficient of large-grained polycrystalline silver (1 grain per sq mm) has previously been measured by Johnson" between 730" and 940°C. The diffusion coefficients which we have measured in single crystals (210 plane normal to diffusion direction) agree within experimental error with values calculated from an extrapolation of Johnson&apos;s curve down to temperatures as low as 500 °C. However, it has been demonstrated that the overall self-diffusion rate in fine-grained polycrystalline specimens (initial grain size of 0.003 cm) becomes measurably larger than the overall rate in a single crystal at a temperature of 600°C, and the discrepancy between the two rates becomes greater as the temperature is further decreased. In fact, it has been possible to obtain satisfactory penetration curves for polycrystalline specimens using the sectioning technique at temperatures as low as 400°C. At this temperature, the penetration is 50 to 100 times greater in the polycrystalline specimens than in a single crystal. Fisher" has developed an analysis whereby the ratio of the rate of the unit diffusion process at the grain boundary to the corresponding rate within the grain can be calculated from the penetration curves and an assumption as to the width of a grain boundary. This analysis applied to our data indicates that the unit process at the grain boundary is faster by a factor of 10&apos; at 475°C when the grain boundary width is taken to be 5. The silver used in most of these experiments was obtained from the Handy and Harmon Co. and listed as 99.97 pct pure. Preliminary experiments on 99.999 pct silver from the Jarrel-Asch Co. indicate a grain-size effect of the same order of magnitude as in the less pure silver. Nominally, these purities are as good, at least, as that of the carbonyl iron used by the authors, but of course if an impurity effect does exist its magnitude might be very dependent upon the nature of both major and minor constituents. The authors have cited the work of other investigators who have found no grain-size effects. Neither Steigman, Shockley and Nix" nor Maier and Nelson8 were able to correlate self-diffusion coefficients of copper with grain size. However, all their measurements were performed at or above 750°C; and on the basis of our work with silver, no grain-size effect would be expected at temperatures above about 0.7 of the absolute melting temperature unless the grain size were exceedingly small. Likewise, in the investigation of the self diffusion of lead by Seith and Keil,14 the lowest temperature at which the diffusion coefficient was measured in polycrystalline specimens was 207°C, which is still sufficiently high so that the lack of a grain-size effect is not surprising. Finally, in those experiments on iron from which they concluded that there was no grain size effect, Drs. Birchenall and Mehl seem to have no information as to the actual grain sizes immediately prior to and following the diffusion anneal. Without this information, we believe that their own experiments offer little support for their hypothesis. F. S. Buffington, I. D. Bakalar, and M. Cohen—The results given in this paper agree in order of magnitude with those tentatively reported by us.27 However, significant differences exist in the two sets of data, and it may be well to make an explicit comparison. The diffusion studies at M.I.T. were conducted on somewhat higher purity iron (99.98 pct Fe) than the grades used by the authors, but this is undoubtedly not the answer. Fig. 4 shows the diffusion results of both laboratories for the gamma phase, omitting the authors&apos; data on the commercial steels, while fig. 5 presents a similar comparison for the alpha phase. The divergence is much more marked in the latter case than in the former. In connection with the M.I.T. determinations, all of the runs in the gamma range and those above 800 °C in the alpha range were conducted with specimens having a relatively thick (0.002 cm) electrodeposit of radioactive iron. This practice minimizes any possible error due to extraneous diffusion that may occur during the heating to and cooling from the operating temperature. An exact solution of Fick&apos;s law for these boundary conditions was used in calculating the diffusion coefficients. At a later time, three runs were made below 800°C, using very thin electrodeposits similar to those of the authors, and the points fell considerably below the values expected from the extrapolation of the results based on the specimens with the thick deposits (compare dash-dot line in fig. 5). However, in the runs with the thin deposits, deviations of 100 pct were found between the individual specimens, whereas the maximum deviation with the thick deposits was less than 25 pct. Accordingly, it is not known at the moment whether the M.I.T. points below 800 °C should be given as much weight as those above 800°C. If this were done, the frequency factor would be of the order of 400 cm2 per sec, which is quite high. In other metals, the frequency factor for self diffusion lies between about 0.1 and 10 cm2 per sec. As the points below

Jan 1, 1951

By Luke L. Y. Chang, Bert Phillips

ThE tendency toward further oxidation of the intermediate oxides and the high volatilization rates of the higher oxides have prevented direct attainment of equilibrium data for the system tungsten-oxygen. As a result, St. Pierre et al.1 have proposed a phase diagram (to 800°C) based on thermody-namic data to 1200°C for the known tungsten oxides (WO2z, W18O49, W20O58, and WO3) and a report on a tungsten suboxide W3O.2 Recent modification of a technique previously described3 5 now permits adequate preservation of compositions of mixtures of metallic tungsten and metal oxides (e.g., of tungsten, cobalt, calcium, samarium, titanium) in order that condensed phase relations may be established to 1700 This method has been applied to study the high-temperature stability of tungsten oxides. In the method used, the desired compositions were sealed in nonreactive containers such that only a small gas volume remained. Each sample then established its own equilibrium atmosphere at temperature. This method has advantages in the study of systems of the W-0 type where knowledge of the condensed phases is desirable but for which composition and pressure of the gas phase are not readily attainable because of oxide volatility. Mixtures of 99.99 pct tungsten metal powder and purified tungsten anhydride (WO3) or in some cases W18O49* were equilibrated in pellet form in sealed

Jan 1, 1964